CKESimpleKey NSPSA-7000 Nissan and Infiniti Replacement Keys User Guide

CKESimpleKey NSPSA-7000 Nissan and Infiniti Replacement Keys

Product Information

The product is called Simple Key and it is a key replacement system for Nissan and Infiniti vehicles. It is powered by CKESimpleKey.com and the packaging part number is NSPSA-7000. The Simple Key is designed to pair with existing smart keys and can be used as a replacement key for the vehicles mentioned in the compatibility list.

The Simple Key comes with an emergency key blade that can be used to unlock the doors in case the battery of the smart key fails. The emergency key blade can be cut at any local hardware store. The product also comes with a tamper- evident security label to ensure its authenticity and security.

It is important to note that pairing a new key will erase all previous keys from the vehicle’s memory, so all existing smart keys must be present during the pairing process. The vehicle’s battery should be in good condition and fully charged before pairing the new key. It is recommended to turn off any electrical components like headlights, radio, and A/C fan to minimize battery draw during the process. The Simple Key does not add any remote features that the vehicle did not have before. Only the original remote features will work, regardless of the buttons included on the Simple Key.

Product Usage Instructions

1. Ensure that you have at least one working smart key for your vehicle.
2. Before starting the pairing process, remove the batteries from all working keys.
3. Locate your vehicle’s key pairing slot, which can be found in the user guide or manual specific to your vehicle model and year.
4. Insert one of the working keys into the key pairing slot at the left side of the dash.
5. Press the vehicle’s Start button once. The dash lights will turn off.
6. Remove the key from the slot.
7. To pair the next key, press and hold the EZ Installer button for 2 seconds and release.
8. Insert the next key into the pairing slot.
9. Press the EZ Installer button to continue.
10. Repeat steps 5-9 for each additional key you want to pair.

Note: It is important to follow the instructions quickly and without delay, as waiting too long between steps may cause the vehicle’s computer to time out, requiring you to start over.

For more information and the most up-to-date vehicle compatibility list, visit CKESimpleKey.com.

IMPORTANT NOTES

• All existing, working smart keys must be present during the pairing process. Once you pair a new key, all previous keys will beerased from the memory. The others will not be functional until you pair them again.
• The emergency key blade should be cut at your convenience. This key blade is inside your new Simple Key and can be used to unlock the doors should the battery in your smart key fail. It can be cut at any local hardware store.
• Vehicle battery should be in good condition and fully charged prior to pairing the new key. Turn off headlights, radio, A/C fan, etc. to minimize battery draw during the process.
• Do not use the EZ Installer™ while the vehicle is in motion. Unplug it from the OBD port before driving the vehicle.
• Only original remote features will work, regardless of buttons includedon the Simple Key. This key does not add remote features that your vehicle did not have before.
• For your security, a tamper-evident security label is installed over the EZ Installer connector. If this label is missing, damaged, or the word “VOID” appears on the EZ Installer, please exchange this Simple Key for a new one at the retailer where it was purchased.
• Before pairing, familiarize yourself with the Simple Key’s compatibility with the make, model, and year of your vehicle below.

COMPATIBILITY LOOKUP

MAKE/MODEL/ YEAR/ PRIMARY DIAL POSITION/ ALTERNATE DIAL POSITION

NISSAN

INFINITI

Visit: CKESimpleKey.com for the most up-to- date vehicle compatibility list.

KEY PAIRING

NOTE: You MUST have at least one smart key that already works with your vehicle in order to use the EZ Installer. If you have no working keys, return the Simple Key to the retailer where it was purchased.

NOTE: The EZ Installer has on-screen instructions to guide you through pairing steps. The numbered steps below provide more detail. Read all instructions prior to starting.

Follow the instructions in the blue portion of the screen first. After you have completed the step, follow the instructions in yellow to move to the next step. For example:

• When you see the message “Press to continue,” press and release the button on the end of the EZ Installer after completing the step written in blue.
• When you see the message “Hold to confirm,” press the button on the end of the EZ Installer for 2 seconds and release after completing the step written in blue.

Instructions have timing requirements. If you wait too long between steps, your vehicle’s computer may time out, requiring you to start over. Once you begin the pairing procedure, move at a quick and even pace.

1. Test your vehicle’s pairing slot by removing the batteries from all working keys and inserting one of those keys into the key pairing slot at the left side of the dash.
   • The location of your vehicle’s key pairing slot can be found in your owner’s manual. The pairing slot may also be called: intelligent key port, prox slot, proximity slot, key slot, or programming slot.
2. Press the brake and try to start the car as normal.
   • If your vehicle starts, continue to step 3.
   • If your vehicle does not start, the pairing slot is not working, and you will not be able to add any keys until it is repaired by a dealership. Do not proceed until the pairing slot is repaired.
3. Find your vehicle’s make, model, and year in the Compatibility Lookup. Turn the dial on the EZ Installer to the position listed for your vehicle’s make, model, and year.
   • NOTE: If more than one dial position exists for your vehicle, try the PRIMARY dial position first. If you are unable to successfully pair the key, unplug the EZ Installer, remove the key, open and close the driver’s door, move the dial to the ALTERNATE position listed for your vehicle, and try again.
4. Enter the vehicle and close all doors.
5. Start with the vehicle in PARK and the engine OFF.
6. Remove the security label from the EZ Installer and insert the EZ Installer firmly into the on-board diagnostic (OBD) port, located under the dash.
   • The location of your vehicle’s OBD port can be found in your owner’s manual.
7. To continue, press and hold the EZ Installer button for 2 seconds, then release.
8. Make sure all keys (new and existing) are present. Ensure all original keysstill have their batteries removed. To continue, press and hold the EZ Installer button for 2 seconds, then release.
9. Close all doors. Turn the hazard lights on. Press the EZ Installer button to continue.
10. Insert one of your original keys into the key pairing slot at the left side of the dash.
    • The location of your vehicle’s key pairing slot can be found in your owner’s manual.
11. Do not press the brake pedal. Press the vehicle’s Start button twice to turn the ignition on. Wait for the next screen.
12. Press the Start button again to turn the ignition off. Press the EZ Installer button to continue.
13. Do not press the brake pedal through the rest of the process. Press the EZ Installer button to continue.
14. Press the EZ Installer button to continue.
15. Wait up to 30 seconds for the next screen to appear.
16. Press the vehicle’s Start button once. The dash lights will turn on. Press the EZ Installer button to continue.
17. Wait up to 30 seconds for the next screen to appear.
18. Press the vehicle’s Start button once. The dash lights will turn off.
19. The vehicle is now in pairing mode. Press button on EZ Installer to continue.
20. Press the vehicle’s Start button once. The security light will flash 5 times.
    • The location of your vehicle’s security light can be found in your owner’s manual.
21. Press the vehicle’s Start button once. The dash lights will turn off. Remove the key from the slot.
22. To pair the next key, press and hold the EZ Installer button for 2 seconds and release. Insert the next key into the pairing slot. Press the EZ Installer button to continue. Repeat steps 20-21. a. To pair additional keys, press and hold the EZ Installer button for 2 seconds and release. Repeat steps 20-21.
23. Once you have paired all available keys, press the EZ Installer button once to continue.
24. To exit key pairing mode, insert one of the paired keys into the slot again. Press the EZ Installer button to continue.
25. Press the vehicle’s Start button to turn the ignition on. Press again to turn the ignition off. Press the EZ Installer button to continue.
26. Unplug the EZ Installer. If the EZ Installer is left in the OBD port for more than 5 minutes, an alarm will sound, reminding you to remove it.
27. Remove the key from the slot and turn off the hazard lights.
28. Reinsert all key batteries.
29. Press brake and start the vehicle.
30. Test all keys.

FREQUENTLY ASKED QUESTIONS

Q: Can I use the same EZ Installer on other vehicles?

A: No, the EZ Installer can only pair Simple Keys to one vehicle. You have the ability to pair additional Simple Keys to the same vehicle. Visit CKESimpleKey.com or your local retailer to purchase additional keys. If the EZ Installer sounds a single beep for 5 seconds, then beeps continuously, this signifies that the device has already been used on another vehicle.

Q: The EZ Installer sounds a single beep for 5 seconds and shows “VIN Error” on screen, then beeps continuously?

A: This signifies that the device has already been used on another vehicle. The EZ Installer can only pair Simple Keys to one vehicle. Return the Simple Key to the retailer from which you purchased it and exchange it for a new unit.

Q: The new key won’t pair to my car?

A: If the EZ Installer doesn’t pair the key to the car, the dial position is likely incorrect. If this is the case, the EZ Installer will continuously sound after you press the pairing button. Check the compatibility section on to confirm the correct dial position for your make, model and year. If an alternate dial position(s) is listed for your vehicle, unplug the EZ Installer, turn the knob to the alternate position, and try pairing again. If the key still won’t pair, please contact customer service at 888-598-8910.

Q: The EZ Installer was unplugged during the pairing process.

A: The EZ Installer must remain plugged into the OBD port until pairingis complete. If the EZ Installer becomes unplugged during the pairing process, turn the ignition to the OFF position, remove the key, and begin the pairing process again, starting with step 3.

Q: The vehicle won’t start with the new key or old keys after attempting to pair.

A: Please call Car Keys Express customer service at 888-598-8910.

FCC STATEMENT

FCC AND ISED REGULATORY STATEMENT

MODEL: 300-0481
FCC ID: X32-APKN1G01
IC: 8797A-APKN1G01

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this device not expressly approved by iKeyless LLC could void the user’s authority to operate the equipment.

HELP

• For help or assistance, please contact technical support at: 888-598-8910.

OTHER KEYS

Visit CarKeysExpress.com to find a variety of award-winning products, like Universal Car Keys, Universal Car Remotes, and OEM keys and remotes. New Chrysler, Dodge, Jeep, Ram, Nissan, and Infiniti Simple Keys are coming soon.

Patent: US10755506B2

Designed and assembled: in the USA 12101 Sycamore Station Place Ste. 140 Louisville, KY 40299

© 2023 Car Keys Express
www.CKESimpleKey.com

References

• Car Keys Express - Discount Key Replacement
• Simple Key
• Simple Key

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>