CYP SDV-C2-RX UHD+ HDMI AV Over IP Receiver Instruction Manual

CYP SDV-C2-RX UHD+ HDMI AV Over IP Receiver

Product Information

• Product Name: SDV-C2-RX UHD+ HDMI AV over IP Receiver
• Manufacturer: CYP (UK) Ltd
• Version: 1.1
• Trademark Acknowledgments: All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

Safety Precautions
Please read all instructions before attempting to unpack, install, or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment:

Contents:

1. Introduction
2. Applications
3. Package Contents
4. System Requirements
5. Features
6. Operation Controls and Functions
   • Front Panel
   • Rear Panel
   • IR Cable Pinouts
   • RS-232 Pinout and Defaults
   • OSD Menu
   • Basic AV Extension
   • Advanced AV Extension

Product Usage Instructions

1. Step 1: Ensure that you have the necessary HDMI receiving equipment such as an HDTV, monitor, or audio amplifier.
2. Step 2: If you plan to use analogue audio, make sure you have the required audio receiving equipment such as headphones, an audio amplifier, or powered speakers.
3. Step 3: Use Premium High Speed HDMI cables for the HDMI connections. Additionally, you will need industry standard Cat.6A or Cat.7 Ethernet cable for the AV over IP extension.
4. Step 4: If you are setting up a distributed video system with multiple transmitters and receivers, you will need a 10 Gigabit Ethernet network switch with jumbo frame and IGMP snooping support.
5. Step 5: If you want to configure distributed matrix, video wall, or multi-view systems, you may require an IP Master Controller or PC control software (optional).

Please refer to the relevant sections in the user manual for detailed instructions on the operation controls and functions of the SDV-C2-RX UHD+ HDMI AV over IP Receiver.

DISCLAIMERS

• The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
• CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document.
• CYP (UK) Ltd reserves the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE

• No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from CYP (UK) Ltd.
• © Copyright 2020 by CYP (UK) Ltd.
• All Rights Reserved.
• Version 1.1

TRADEMARK ACKNOWLEDGMENTS

• All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
• Please completely disconnect the power when the unit is not in use to avoid wasting electricity.

VERSION HISTORY

INTRODUCTION

• This AV over IP Receiver is designed for high-quality, IP routable, AV extension with minimum latency. By using a sophisticated ultra-light compression scheme (lossless for most content) it’s a great solution for extending 4K audio/video streams and data. Advanced HDMI content such as HDR (High Dynamic Range), 10-bit colour and multi-channel HD Bitstream audio can be transmitted in pass-through mode.
• The use of high quality 10 Gigabit Ethernet ports and Cat.6A or better cable allows for point-to-point transmission of the video signal up to 100m. Multiple control and data signals may also be transmitted along with the audio and video, including IR, RS-232, USB 2.0, and Ethernet.
• When combined with the optional IP Master Controller or control software, the functionality of the receiver expands exponentially. Multiple transmitters and receivers may be combined with one or more 10 Gigabit Ethernet switches and the units can be used together to form a distributed video matrix, a multiviewer system, or a video wall system adding to their flexibility in large event installations.
• The integrated USB hub of each receiver can function as a simple point to point KVM extension or freely routed between any two endpoints. This type of USB KVM routing flexibility enables a wide range of multi-user, control room, or on-demand installation scenarios.
• The built-in EDID and HDCP management functionality enables the unit to fit into every situation. Basic configuration of the unit can be achieved via front panel buttons with an OSD (On-Screen Display). Advanced control requires the optional IP Master Controller, or control software, and a LAN connection.

APPLICATIONS

• Video, Audio, LAN, IR, and USB 2.0 over Cat.6A extension Point-to-Point Secure Video Conferencing
• Hotel or convention center display
• Multi-monitor broadcast
• Distributed video matrix system
• Distributed video wall system
• Remote KVM system control

PACKAGE CONTENTS

• 1× UHD+ HDMI AV over IP Receiver
• 1× 12V/3A DC Power Adapter
• 1× Power Cord
• 1× Operation Manual

SYSTEM REQUIREMENTS

• HDMI receiving equipment such as an HDTV, monitor, or audio amplifier
• Analogue audio receiving equipment such as headphones, an audio amplifier, or powered speakers
• The use of Premium High Speed HDMI cables, and industry standard Cat.6A, or Cat.7 Ethernet cable is required.
• A 10 Gigabit Ethernet network switch with jumbo frame and IGMP snooping support is required for distributed video systems (Optional, required for multi-transmitter/receiver systems)
• IP Master Controller or PC control software to configure distributed matrix, video wall, or multi-view systems (Optional)

FEATURES

• HDMI 2.0 and DVI 1.0 compatible
• HDCP 2.2 and HDCP 1.x compliant
• 1 Cat.6A input
• 1 HDMI output
• 1 analogue stereo input & 1 analogue stereo output
• 2 USB 2.0 (Type-A) ports and 1 USB 2.0 (Mini-B) port
• IP routable with minimum latency (requires optional IP Master Controller or control software)
• Ultra-light compression, lossless for most content
• Extension up to 100m in Point-to-Point mode (with Cat.6A cable) Supports independent breakaway A/V matrix switching with minimum latency, video wall generation, and multi-
• view compositing (requires optional IP Master Controller/control software)
• Supports pass-through of 10/12-bit HDR sources (Point-to-Point and Bypass modes only)
• Supports pass-through of audio formats including LPCM (up to 8 channels), Bitstream and HD Bitstream from HDMI or DP sources Analogue stereo audio extension, insertion and
• extraction (insertion and extraction requires optional IP Master Controller/control software) Unit can be powered directly by PoE when connected to a 10 Gigabit Ethernet (10GbE)
• switch that provides PoE (802.3at)
• Basic configuration via front panel buttons with an OSD
• Supports the use of an external control center (IP Master Controller) or control software to provide expanded functionality (Contact your authorised dealer for more information)

OPERATION CONTROLS AND FUNCTIONS

Front Panel

1. P OWER LED : This LED will illuminate to indicate the unit is on and receiving power.
2. USB 2.0 (Type-A) Ports: Connect directly to standard USB devices such as a mouse, keyboard or flash drive to extend their USB functionality to the currently active/routed USB Device Mode transmitter.
3. STATUS LED BLOCK:
   • GbE LED: This LED will illuminate and blink to indicate a live and active connection on the local gigabit Ethernet port.
   • VIDEO LED: This LED indicates video streaming activity over the Cat.6A port. It will illuminate green when a video signal is being transmitted. When no video is active the LED will remain off, even if the streaming connection is valid.
   • LINK LED: This LED will illuminate and blink to indicate data transmission activity across the Cat.6A streaming connection.
   • USB LED : This LED will illuminate when the unit’s USB ports have successfully paired with the USB ports on another unit. This LED will remain off if the unit’s USB ports are not currently paired and in stand-by mode.
4. MENU Button : Press to enter the OSD menu, or to back out from menu items.
5. (MINUS) Button : Press to move down or adjust selections within OSD menus.
6. + (PLUS) Button : Press to move up or adjust selections within OSD menus.
7. ENTER/INFO Button: When inside an OSD menu, press to confirm a selection or to go deeper into a menu item. When not in a menu, press to activate the Information OSD.

Rear Panel

1. HDMI OUT Port: Connect to an HDMI TV, monitor, or amplifier for digital video and audio output.

2. CAT6A/7 Port : Connect directly to a compatible transmitter for Point- to-Point extension, or to a 10 Gigabit Ethernet switch for distributed matrixing (requires IP Master Controller or control software), with a single Cat.6A/7 cable for extension of all data signals.
   Note: If the connected network switch supports the IEEE 802.3at-2009 PoE (Power over Ethernet) standard, this unit can optionally be powered directly via this Ethernet port.

3. AUDIO PORTS:

   • OUT Por t: Connect to powered speakers or an amplifier for stereo analogue audio output.
   • IN Port: Connect to the stereo analogue output of a device such as a CD player or PC.
     Note: When units are connected directly in a Point-to-Point configuration, audio is routed directly from the IN Ports to the opposite end’s OUT Ports. Free routing can only be configured by use of the optional IP Master Controller or control software.

4. IR PORTS:

   • OUT Port : Connect to an IR Blaster to broadcast IR signals from a connected receiver to devices within direct line-of sight of the IR Blaster.
   • IN Port : Connect to an IR Extender to receive IR control signals and extend them to devices connected to a connected transmitter. Ensure that the remote being used is within direct line-of-sight of the IR Extender.
     Note: Currently, only 38KHz IR signal extension is supported.

5. RS-232 3-pin Terminal Block: Connect directly to a PC, laptop or serial controllable device with a 3-pin adapter cable to extend the RS-232 signal between units.

6. LAN Port: C onnect to an Ethernet supporting device or to your local network as appropriate to extend the network between units.

7. USB/SERVICE (Mini-B) Port: Connect directly to a standard USB host such as a PC or laptop to extend their USB functionality to all currently connected/routed USB devices.
   Note: This port is only active when “USB Control Mode” is set to “Device”. In a Point-to-Point extension configuration, only one of the two units should be set as a USB Device to avoid conflicts.

8. DC 12V Port : Plug the 12V DC power adapter into this port and connect it to an AC wall outlet for power.
   Note: Optional, not required if the unit is powered via PoE.

IR Cable Pinouts
RS-232 Pinout and Defaults

Serial Port Default Settings

Baud Rate| 57600
Data Bits| 8
Parity Bits| None
Stop Bits| 1
Flow Control| None

Note: The default Serial Port baud rate can only be changed by use of the optional IP Master Controller or control software.

OSD Menu
All functions of this unit can be controlled by using the OSD (On Screen Display) which is activated by pressing the MENU button on the front of the unit. Use the + (PLUS), − (MINUS), and ENTER buttons to navigate the OSD menu. Press the MENU button to back out from any menu item and then press it again to close the menu.

MAIN MENU

OSD
Device Setting
Information
USB Information
Factory Setting

The individual functions of the OSD will be introduced in the following section. Items marked in BOLD are the factory default settings.

OSD

2ND LEVEL| 3RD LEVEL
Display Information| ON
Off
Information Timeout| Off
10~40 Sec (10 Sec)
Menu Timeout| Off
10~40 Sec (10 Sec)
Menu H Position| 0~100 (90)
Menu V Position| 0~100 (10)

1. Display Information : Enable or disable the Information OSD.
2. Information Timeout: Set the display timeout for the Information OSD.
3. Menu Timeout: Set the display timeout for the OSD Menu.
4. Menu H Position: Set the horizontal position of the OSD Menu.
5. Menu V Position: Set the horizontal position of the OSD Menu.

DEVICE SETTING

2ND LEVEL| 3RD LEVEL
USB Control Mode| HOST
Device
USB Virtual Hub (USB Device Mode only)| OFF
On

1. USB Control Mode: Enable or disable the USB 2.0 (Mini-B) port for connection to USB host devices such as a PC or laptop. Selecting “Device” enables the USB 2.0 (Mini-B) port. Selecting “Host” disables the USB 2.0 (Mini-B) port.
   Note: In a Point-to-Point extension configuration, only one of the two units should be set to “Device” to avoid conflicts.

2. USB Virtual Hub: Enables or disables the “simultaneous connection” USB mode which allows the PC/Laptop connected to this unit to be paired with the USB devices on up to 7 “Host” mode units.
   Note: Only available when USB Control Mode is set to “Device”. USB routing can only be configured by use of the optional IP Master Controller or control software and is not valid in Point-to-Point configurations.

INFORMATION

2ND LEVEL| 3RD LEVEL
Resolution| [Current Output Resolu- tion]
Status| RECEIVER
FW Version| [Current Firmware Version]
IP| [Current IP Address]
MAC| [Unit’s MAC Address]
SN| [Unit’s Serial Number]

Information: Shows details of the unit’s current status including output resolution, streaming direction status, firmware version, IP address, MAC address, and serial number.

USB INFORMATION

2ND LEVEL| 3RD LEVEL
IP Mode| [Unit’s USB IP Mode]
IP| [Unit’s USB IP Address]
MAC| [Unit’s USB MAC Address]
Pair MAC 1~7| [USB Mac Addresses of Connected USB Devices]

USB Information: Shows status details of the unit’s USB mode and current USB connections.

FACTORY SETTING

2ND LEVEL| 3RD LEVEL
Are you sure?| NO
Yes

Factory Setting : Selecting YES will reset the unit’s settings back to their factory defaults.

Basic AV Extension

Point-to-Point (One Way)
The most basic extension configuration available is a point-to-point system with a single transmitter connected directly to a single receiver. In this configuration the HDMI/DP input on the transmitter side is transmitted to the connected receiver side without modification to the audio or video format. The analogue stereo audio input on the transmitter transfers audio directly to the analogue stereo audio output on the receiver. The LAN, RS-232 and IR ports form direct connections between transmitter and receiver as well. This configuration is ideal for basic video extension as well as remote KVM applications. Note: This configuration does not use or require an external control center such as the IP Master Controller to function. No audio insertion/extraction is performed in this configuration.

Advanced AV Extension

• IP Master Controller
  • The IP Master Controller is a hardware solution designed to provide a unified and easy method to access and control all of the transmitters and receivers in a system. It provides a user-friendly, and operating system agnostic, web-based interface allowing easy control over all of the most critical functions within a distribution system.
  • The IP Master Controller hardware is an optional component and is not included with individual transmitter, receiver, or transceiver units. Please contact your authorised dealer for more information.

Note: Interface images are for example only and may differ from the delivered product. Full operational documentation can be found within the IP Master Controller’s manual.

Configuration Examples
When combined with the IP Master Controller, and a 10 Gigabit Ethernet switch, this extension system gains a large number of additional configuration options including: multi-in/multi-out matrix switching with breakaway audio, video wall creation, and a multiview output mode. Audio extraction and embedding is fully controllable. Additionally, audio, USB, IR, and RS-232 routing can be fully controlled.

1. Matrix Configuration
2. Video Wall Configuration
3. Multiview (PiP/PoP/Quad/Etc.) Configuration
4. KVM Switch Configuration

CONNECTION DIAGRAM

SPECIFICATIONS

Technical Specifications

• HDMI Bandwidth 18Gbps
• CAT6A/7 Bandwidth 10Gbps
• Input Ports
  • 1×10GbE LAN (RJ-45)
  • 1×Stereo Audio (3.5mm)
• Output Ports
  • 1×HDMI (Type-A)
  • 1×Stereo Audio (3.5mm)
• Pass-through Ports
  • 1×IR Extender (3.5mm)
  • 1×IR Blaster (3.5mm)
  • 1×RS-232 (3-pin Terminal Block)
  • 2×USB (Type-A)
  • 1×LAN (RJ-45)
• Pass-through/Service Port 1×USB 2.0 (Mini-B)
• IR Frequency 38kHz
• Baud Rate 57600 (Default), up to 115200bps
• Power Supply PoE (802.3at) or 12V/3A DC (US/EU standards, CE/FCC/UL certified)
• ESD Protection (HBM)
  • ±8kV (Air Discharge)
  • ±4kV (Contact Discharge)
• Dimensions (W×H×D)
  • 215mm×25mm×108mm [Case Only]
  • 215mm×25mm×116.7mm [All Inclusive]
• Weight 916g
• Chassis Material Metal (Steel)
• Chassis Colour Black
• Operating Temperature 0˚C – 40˚C/32˚F – 104˚F
• Storage Temperature -20˚C – 60˚C/-4˚F – 140˚F
• Relative Humidity 20 – 90% RH (Non-condensing)
• Power Consumption 18.51W

Video Specifications

Supported Resolutions (Hz)

| Input| Output
---|---|---
10GbE| HDMI
720×400p@70/85| P| P
640×480p@60/72/75/85| P| P
720×480i@60| P| P
720×480p@60| P| P
720×576i@50| P| P
720×576p@50| P| P
800×600p@56/60/72/75/85| P| P
848×480p@60| P| P
1024×768p@60/70/75/85| P| P
1152×864p@75| P| P
1280×720p@50/60| P| P
1280×768p@60/75/85| P| P
1280×800p@60/75/85| P| P
1280×960p@60/85| P| P
1280×1024p@60/75/85| P| P
1360×768p@60| P| P
1366×768p@60| P| P
1400×1050p@60| P| P
1440×900p@60/75| P| P
1600×900p@60RB| P| P
1600×1200p@60| P| P
1680×1050p@60| P| P
1920×1080i@50/60| P| P

Supported Resolutions (Hz)

| Input| Output
---|---|---
10GbE| HDMI
1920×1080p@24/25/30| P| P
1920×1080p@50/60| P| P
1920×1200p@60RB| P| P
2560×1440p@60RB| P| P
2560×1600p@60RB| P| P
2048×1080p@24/25/30| P| P
2048×1080p@50/60| P| P
3840×2160p@24/25/30| P| P
3840×2160p@50/60 (4:2:0)| P| P
3840×2160p@24, HDR10| P| P
3840×2160p@50/60 (4:2:0), HDR10| P| P
3840×2160p@50/60| P| P
4096×2160p@24/25/30| P| P
4096×2160p@50/60 (4:2:0)| P| P
4096×2160p@24, HDR10| P| P
4096×2160p@50/60 (4:2:0), HDR10| P| P
4096×2160p@50/60| P| P

Audio Specifications

Digital Audio

HDMI Output

LPCM
Max Channels| 8 Channels
Sampling Rate (kHz)| 32, 44.1, 48
Bitstream
Supported Formats| Standard & High-Definition
10GbE Input

LPCM
Max Channels| 8 Channels
Sampling Rate (kHz)| 32, 44.1, 48
Bitstream
Supported Formats| Standard & High-Definition

Analogue Audio

Analogue Input

Max Audio Level| 2Vrms
Impedance| 10kΩ
Type| Unbalanced
Analogue Output

Max Audio Level| 2Vrms
THD+N| < −80dB@0dBFS 1kHz (A-wt)
SNR| > 80dB@0dBFS
Frequency Response| < ±1dB@20Hz~20kHz
Crosstalk| < −80dB@10kHz
Analogue Output

Impedance| 470Ω
Type| Unbalanced

Cable Specifications

8- bit
High Speed HDMI Cable
HDMI Output| 15m| 10m| 5m| 3m
Ethernet Cable
Cat.6A/7| 100m

Bandwidth Category Examples:

• 1080p (FHD Video)
  • Up to 1080p@60Hz, 12-bit colour
  • Data rates lower than 5.3Gbps or below 225MHz TMDS clock
• 4K30 (4K UHD Video)
  •  4K@24/25/30Hz & 4K@50/60Hz (4:2:0), 8-bit colour
  •  Data rates higher than 5.3Gbps or above 225MHz TMDS clock but below 10.2Gbps
• 4K60 (4K UHD+ Video)
  • 4K@50/60Hz (4:4:4, 8-bit)
  • 4K@50/60Hz (4:2:0, 10-bit HDR)
  • Data rates higher than 10.2Gbps

ACRONYMS

Blanking)
XGA| Extended Graphics Array
Ω| Ohm

CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton, Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: sales@cypeurope.com
www.cypeurope.com
RDV1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>