KINGSTON FSC4688SVL Serena 1.2 GPM Widespread Instruction Manual
- June 13, 2024
- Kingston
Table of Contents
Parts:
NOTICE
Failure to follow all directions may cause leaks which may result in water
damage
www.kingstonbrass.com
TOLL-FREE CUSTOMER SERVICE: 1-877-2-KBRASS
TECHNICAL SUPPORT E-mail:
service@kingstonbrass.com
12775 Reservoir Street, Chino, CA 91710
CARE AND MAINTENANCE OF YOUR FAUCET
Your Kingston Brass faucet has been finished to the most strict standards; however, due to the high content of minerals in the water, your finish may appear dull and tarnished after time. These are some do’s and don’ts to maintain the luster on your faucet for many years to come.
DO
- Use a silicon based caulking when installing.
- Clean your faucet with only a mild soap and water solution.
- Dry your faucet after using It.
- Give it a coat of Carnauba Wax periodically.
DON’T
- Use plumbers putty when installing the faucet.
- Use any abrasive cleaning agents.
It may seem like a very simple and short list but it is that simple to
maintain your faucet, looking shiny and new.
If your faucet is already looking somewhat dull and tarnished, before
replacing it, try cleaning it with a 50/50 solution of vinegar and water, you
may need to soak some rags and wrap around those stubborn areas, leave
overnight and rinse completely in the morning, apply Carnauba wax once you
have removed the mineral deposits.
INSTALLATION INSTRUCTIONS
Widespread Lavatory Faucet with or without Pop-Up
Need Tools:
BEFORE BEGINNING INSTALLATION:
- Flush plumbing lines to clear any debris.
- Shut off both supply lines after flushing.
| 1. Remove the Tee Connector and spout mounting hardware from spout
---|---
| 2. Sparingly apply a small bead of silicon caulking around the center hole
on top of the sink (do not use Plumber’s Putty as it may damage finish and
void warranty).
| 3. From the top of the sink insert the spout base ring (if applicable) and
spout through the center hole. Slip the spout mounting hardware back onto the
spout, hand tighten lock nut. Insert the pop-up rod through the hole in the
back or top of the spout. (see pop-up installation below). Rotate the notched
metal washer, to insure smooth movement of the pop-up rod. Tighten the brass
lock nut, test pop-up rod for ease of operation.
| 4. Place the tee connector washer and thread tee connector on to spout
shank.
| 5. Hot and Cold Stem assemblies are easily Identifiable by a Red(Hot) or
Blue(Cold) band, insert stem assembly through side holes from below making
sure to have bottom nut and metal washer threaded on stem assembly.
| 6. While holding from under the sink install trim ring and thread
escutcheon on to stem assembly, adjust to a suitable height to allow
sufficient space for handle to operate smoothly. Tighten bottom nut, please
make sure to align direction of lever handles before tightening stem.
| 7. Attach flexible hoses to the outlet port of hot and cold valve assembly,
you may need to loop the hoses as shown on graphic and be caution not to
overtighten.
| 8. Apply Teflon tape on all male threading and install inlet supply lines
(not included) to bottom inlet port of hot and cold valve assembly.
| 9. Install Pop-up assembly as per instructions below. Install flange body
up through the drain opening, hold the drain flange body in position with
pivot rod opening facing the back of sink and hand tighten the mounting nut.
| 10. Place pivot rod into pivot rod opening. Slide pivot nut over pivot rod
and thread it on the drain body. Tighten firmly.
| 11. Guide the pivot rod through one of the holes on the lift rod strap and
secure it with the spring clip.Then adjust the height of the lift rod by
resetting the clevis screw. With lift rod in position on the faucet, insert
lift rod through lift rod strap and secure with the clevis screw.
| 12. Remove aerator and turn on both hot and cold valves, let water run for
at least one minute, this
will clear any debris left in the line, reinstall aerator.
Warning!!!
- Do not over-tighten nut during installation.
- Over-tighten may crack the valve and cause severe leak.
Mounting nut installation instructions
To install the mounting hardware:
|
---|---
- Unscrew Both adjustment screws as much as possible without removing them.
- Thread lock nut onto the valve assembly and slip on the metal washer.
- Once the valve assembly has been secured from the top, hand tighten brass lock nut all the way to the top.
- Gently secure the screws to lock the valve assembly in place use only a Phillips head screw driver. Do not over-tighten as this may damage steel washer, see illustration.
- Do not use any power tools as this may damage the valve assembly and cause leaking.
www.kingstonbrass.com
TOLL-FREE CUSTOMER SERVICE: 1-877-2-KBRASS
TECHNICAL SUPPORT E-mail:
service@kingstonbrass.com
12/775 Reservoir Street, Chino, CA 91710
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>