GODIAG GB101 Automotive Battery Load Tester Diagnostic Analyzer Monitor User Manual
- June 13, 2024
- GODIAG
Table of Contents
GODIAG GB101 Automotive Battery Load Tester Diagnostic Analyzer Monitor
GODIAG GB101 automotive battery load tester is used to monitor the auto battery, cranking system and charging system. After install it to the battery, the mobile can connect it via Bluetooth 4.0. When some problems happen in battery, cranking or charging system, it can send notification alert to the user. Besides, the user also can test and review the test record via app.
Product Parameters
| Average Current | 15mA |
|---|---|
| Input Voltage | 6-20V |
| Opera:t i ng Temperature | -40 °C -90°C |
| Dimensions | 5.641.6cm |
| Voltage Accuracy(9″’16V) | + 0.03V |
| Short-circuit Protection | Built-in |
| --- | --- |
| Reverse Connection Protection | Built-in |
| Bluetooth | 4.0 |
| Bluetooth Name | Battery Asst |
| App Keyword | Battery Asst |
Product Parameters
Product shell and wire made by fireproof materials are durable for high temperature.
Built-in short circuit prevention safety switch, it will automatically cut off power when current is too large. Also reverse connection protection built-in, will not damage vehicle and product in case of reverse polarity.
How to Install the Product
Install battery monitor to the battery of the vehicle
- Install red connector to positive pole and black to negative pole, then firm them.
- Fix the product body with velcro. Try to find a paste position that Bluetooth signal will not be blocked. Clean the surface before pasting.
App Installation
|
|
- Scan the QR code of the product.
- Search “Battery Asst” on App Store or Google Play to download app.
App Using Scene
If no block, the mobile can receive the signal in 10 meters between the mobile and product. If exceed 10 meters or block exists, it will affect the signal strength.
App Operation
-
Click app icon, run app, it is necessary to turn on the Bluetooth of mobile.
-
Please allow app to access location even when not using the app. If users do NOT do that, the product will not automatically notify the user when monitoring the problem.
-
Please allow to receive notifications. Notifications including the car battery, cranking system and charging system and problem alert. If users do NOT do that, they can not receive relative notification. While if allowed, when the mobile phone enters the range of Bluetooth, it will receive the information notification no matter if the app is running or not.
App Interface Instruction-First Interface
- It shows the device name.
- When in connecting status, the icon is in white, when in not connected status, the icon is in black. It is default that it will connect to the latest device automatically, also can connect or disconnect manually.
- System Setup icon, click to enter System Setup.
- Show battery state of charge.
- Show battery real-time voltage, and graphical display the state of charge.
- Battery status: 1. Voltage normal, 2. Battery Charging , 3. Abnormal voltage.
- Show battery real voltage graph, click “( )” , users can review the voltage graph of other dates.
- Battery voltage test icon, it is defaulted as first interface, selected status is white, the others are black.
- Cranking system test icon, when the engine start each time, it will test cranking system automatically, selected status is white, the others are black.
- Charging system test icon, it can test charging system manually, selected status is white, the others are black.
- Trip record icon, records each starting time, stopping time and driving time of the vehicle, selected status is white, the others are black.
App Interface Introduction-Voltage History Graph
- Date select: click “ ” , you can review the voltage graph at selected date.
- Historical voltage graph, click the graph, it will appear slider, the orange figure on the graph indicates the voltage value during this time period.
App Interface Introduction- System Setup
- 1. Battery daily notification: green is on, gray is off. System default is no more than one notification in 9 hours, the notification frequency can be setup.
- Start exception notification: green is on, gray is off. System default is no more than one notification in 6 hours, the notification frequency can be setup.
- Battery alarm: When battery power fal Is to reach the set value, user will receive app notification about charge level.
App Interface Introduction-Cranking Test
- Engine start ti me.
- Cranking test: when engine starts, the device will test the cranking system automatically and store the test result. Usually, if the cranking voltage is higher than 9.6V, it means normal. But if the cranking voltage is less than 9.6V, it means abnormal. If the cranking voltage is too low, maybe aging of battery, low power, or starter fault etc.
- Display the cranking voltage values.
- The cranking voltage graph.
App Interface Introduction-Charging Test
-
Click to start the test, automatically test idle condition voltage.
-
For high RPM voltage test, it is necessary to increase RPM as below and hold for 3-5 seconds, then test is finished.
4cyl – 2500/min
6cyl – 2000/min
Beyl – 1600/min -
Description of charging voltage Test:
Charging Voltage: normal Charging system shows the alternator output normal, no problem detected.
Charging Voltage: low
Charging voltage is low. Check engine transmission belt is slip or disconnect, check whether the line connection between alternator and battery is normal or not. If transmission belt and line connection is good, please follow the car manufacturer’s recommendations to exclude the alternator failure.
No Voltage Output: no engine voltage output is detected. Check whether the alternator cable and the alternator belt are working properly.
- 4. Charging test finished time .
- 5. Click button to recheck.
App Interface Introduction-Trip Record
- Click search button to review driving records.
- Starting time, running time and stopping time of each driving
Tips
- Product should not be used overpass the specified voltage ranged(6-20V), excessive input voltage may damage the device.
- App requires smartphones with: Android 4.3 and higher, iPhone 4S and higher.
- When mobile enters Bluetooth range, it will receive notification.
- If first time choose “not allowed to access location”, you will not receive notification alert. If want to use this function in future, you can open the location in phone Settings by selecting “always allow location access”.
- If the daily test alert function is not open, when the mobile is close to device, it also can’t get notification of the daily test result. You can set to allow notification both in app and phone’s Settings.
- If the exception test alert function is not open, when the mobile isclose to device, it also can’t get notification of monitoring exception.You can set to allow notification both in app and phone’s Settings.
- Firmware update will clear all data in the device, please open app waiting for sync finished before update firmware.
- All historical data will be stored in the phone side, app upgrade will not lose the historical data.But if app is uninstalled, the phone terminal data will be clear.
- The device will automatically monitor vehicle battery, cranking and charging systems, device can store data up to 35 days. Please use the app or make phone enters device Bluetooth range at least one time within each 35 days. Then device historical data will be synchronized to phone.
- If app can not search Battery Monitor, please ensure mobile’s Bluetooth is on and close to the device without blocks.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.d This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following.
Measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Battery Asst
Documents / Resources
|
GODIAG GB101 Automotive Battery Load Tester Diagnostic Analyzer
Monitor
[pdf] User Manual
GB101 Automotive Battery Load Tester Diagnostic Analyzer Monitor, GB101,
Automotive Battery Load Tester Diagnostic Analyzer Monitor, Battery Load
Tester Diagnostic Analyzer Monitor, Tester Diagnostic Analyzer Monitor,
Diagnostic Analyzer Monitor, Analyzer Monitor, Monitor
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>