QUIO QU-RDT2-HF Touch Keypad LCD Display Reader Installation Guide
- June 13, 2024
- QUIO
Table of Contents
QUIO QU-RDT2-HF Touch Keypad LCD Display Reader
Product Information
- Product Name: QU-RDT2-HF
- Description: Touch Keypad LCD Display Reader
- Model Number: V0103
Specifications
| Spec / Item | QU-RDT2-HF |
|---|---|
| Transmit Frequency | 125KHz / 13.56MHz |
| Read Range | 5~10cm / 2~6cm |
| Baud Rate | 19,200 bps (4,800~230,400 bps) |
| Card Compatibility | EM or ISO14443A/B/15693/Mifare |
| Card Read Time | 0.1Sec |
| Keypad | 12 keys |
| LED Indicator | 3 LED (RGB) |
| Communication ID | RS485 and Wiegand (26/32/34/42/66 Bits) |
| LCD Display | 128×64 Dots (16×4 Char) LCD with backlight |
| Anti-Tamper Facility | Built-in (IR) |
| Beep Tone | Built-in Buzzer |
| Input Voltage | 8V~28V DC / 0.5 ~ 2W |
| Dimension (W x H x D) | 89.4 x 124 x 12 mm |
Product Usage Instructions
Installation Note:
This product uses a touch panel. When installing and tightening the screws,
follow these steps:
- Power off the device for at least 5 seconds.
- During this period, do not touch the touch panel or put anything on it.
- After the power off period, reboot the device.
This procedure is necessary for panel calibration and recalculation of the touch control function to ensure correct and accurate operation.
QU-RDT2-HF Instructions:
Setup:
- Login: # + # + 0 + 1 (Beep) + PIN + # (Factory PIN: 1234)
- Logout: # + # + 0 + 0 (Beep)
ID Setup:
- Login first, then perform the following settings:
- Set ID: # + # + 0 + 2 (Beep) + ID (Factory ID: 1)
- Set Date and Time : # + # + 0 + 3 (Beep) + YYYYMMDDhhnnss (e.g., 20110129032523 for January 29, 2011, 03:25:23)
- Modify Login PIN: # + # + 0 + 4 (Beep) + New PIN
- Set Backlight Delay: # + # + 0 + 5 (Beep) + Time (0 for light steady, 1-250 seconds)
- Set Interface: # + # + 0 + 6 (Beep) + Interface (0 for Wiegand, 1 for RS485, 2 for Wiegand & RS485, Factory: 2)
- Set Language: # + # + 0 + 7 (Beep) + Language (0 for English, 1 for Chinese, Factory: 0 – English)
- Set Encode: # + # + 0 + 8 (Beep) + Encode (0 for UNICODE, 1 for BIG5, 2 for GB2312, Factory: 0 – UNICODE)
- Set Status : # + # + 0 + 9 (Beep) + Class (0 for Disable, 1 for Enable, Factory: 0 – Disable)
Change Work Status:
- Start Work: # + 1 (Beep)
- Finish Work: # + 2 (Beep)
Leave on Duty:
-
+ 3 (Beep)
Please enable Status Function first.
Back for Duty:
- Start Overtime: # + 4 (Beep)
- Finish Overtime : # + 5 (Beep)
-
+ 6 (Beep)
QU-RDT2-HF Specification
Spec / Item QU-RDT2-HF
- Transmit Frequency 125KHz / 13.56MHz
- Read Range 5~10cm / 2~6cm
- Baud Rate 19,200 bps (4,800~230,400 bps)
- Card Compatibility EM or ISO14443A/B/ 15693 / Mifare
- Card Read Time 0.1Sec
- Keypad 12 keys
- LED Indicator 3 LED (RGB)
- Communication RS485 and Wiegand (26/32/34/42/66 Bits)
- ID 0001 ~ 9,999
- LCD Display 128×64 Dots (16×4 Char) LCD with backlight
- Anti-Tamper Facility Built-in(IR)
- Beep Tone Built-in Buzzer
- Operating Temperature -10˚C~60˚C
- Input Voltage 8V~28V DC / 0.5 ~ 2W
- Dimension (W x H x D) 89.4 x 124 x 12 mm
Installation Note
- This product uses the touch panel. when you installed and tightened the screws, please POWER OFF over 5 seconds, and in this period,
- PLEASE DO NOT put anything on the touch panel(e.g. Finger..etc) then reboot.
- This procedure is for the panel calibration and recalculation the touch control function, to ensure it can work correct and accurate
QU-RDT2-HF Instructions
Clear ：’✱ ‘
Change Work Status：
Please enable Status Function first.
Quick-Ohm Küpper & Co. GmbH
Cronenfelderstraße 75 | 42349 Wuppertal
Tel: +49 (0) 202 404329 | Fax: +49 (0) 202 404350
E-Mail: kontakt@quio-rfid.de Web: www
.quio-rfid.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>