QUIO-RFID QUIO QU-ER-80-4 Chip Card Reader User Guide
- June 11, 2024
- QUIO-RFID
Table of Contents
QUIO-RFID QUIO QU-ER-80-4 Chip Card Reader
Product Information
The product is a QR code reader that can be connected to a PC via mini USB data cable and internet cable. The default fixed IP of the QR code reader is 192.168.1.99. The product has various function parameter specifications such as network parameter configuration, output format selection, and external parameter settings. It also has features such as horn, scan fill-in light, and bar code/QR code setting.
Product Usage Instructions
- Double click to enter the QR code Reader parameter setting page.
- Use mini USB data cable to connect the QR code reader to the PC, and wait for the fill-in light to turn on and the buzzer to ring indicating that the QR code reader has started. Then, use the internet cable to connect the QR code Reader to PC.
- Manually set the same network segment with the QR code Reader on the client PC by following the operation as shown in the picture on the website. This will allow you to get the QR code reader parameter via the software.
- Configure the function parameter specifications by clicking on the setting button.
- Set the output format selection, card number prefix suffix format, and WG timing sequence definition as needed.
- Double click on“ ”，enter QR code Reader parameter setting page,
- Use mini USB data cable connect the QR code reader to PC, fill-in light on, buzzer rings, QR code reader start done, then use the internet cable connect the QR code Reader to PC.
- QR code Reader default fixed IP is 192.168.1.99, client PC manual setting the same network segment with the QR code Reader, follow the operation as below Picture, can get the QR code reader parameter via the software
Function parameter specification:
network parameter
Mainly include network parameter of the QR code Reader, configure relevant
parameter, click setting can done setting.
Internet mode: default fixed IP:192.168.1.99 mode, can select
auto obtain mode
【HTTP address】 HTTP output mode need use domain name address
【HTTP sever port】 HTTP output mode need use sever port；
【Docking services Voice 】 HTTP output mode， sever docking interface language
PHP、 JSP、C#、ASP option）
format parameter setting
【output format selection】 USB Virtual keyboard、 USB virtual serial port、 HTTP、
MQTT、 RS232、WG26、WG34、RS485、access control system output( not enabled)、TCP、UDP
functions
【card number output format】6H、8H、6H10D、8H10D、2H3D+4H5D option， this card
number format setting is invalid for QR Code
【HID format parameter】 data output if send carriage return、 If send line feed，
this parameter setting is invalid for USB virtual serials port, carriage
return only valid for USB virtual keyboard, linefeed only valid for RS232
【parameter】 can adjust correspond parameter as you need, this parameter
setting is invalid for USB virtual serial port, only valid for RS485, RS232
【QR code serial port output format】 DEC、HEX、DEC Reverse、 Hex Reverse、 ASCII
option，（this parameter only valid for RS485,RS232“RS485、RS232”，Hex、Hex Reverse
output format is Hex card number, total bit is odd, output is ASCII， Even
number, output is HEX card number）
external parameter
【rest setting】0 for not reset，12hours interval、24 hours interval；
【working mode】 common mode, single mode, interval mode，
Common mode： can reading QR code constantly；
single mode： the same QR code can not reading constantly；
interval mode： reading the same QR code need waiting 15 seconds
【horn】 not enabled；
【scan fill-in light】 turn on and off for camera fill-in light；
bar code, QR code setting
setting QR code prefix and suffix, add the correspond prefix and suffix to QR
code
【prefix and suffix input format】 ASCII、HEX option， setting the prefix and
suffix format output；
card number prefix suffix format
setting prefix and suffix, add the correspond prefix and suffix to card
number(this parameter only valid for RS485 、 RS232)
【 prefix and suffix input format】 ASCII、HEX option， setting the prefix and
suffix format output；
【serial port output format】 ASCII、 HEX option， setting the prefix and suffix
format output；
WG timing sequence defination
setting the wiegand output high-low pulse time period, setting the timing
sequence according to the actual controller
QR code parameter setting
【card number format】8H10D、Hex、2H3D+4H5D option， default is 8H10D（this
parameter only valid for WG26、WG34） other function parameter not enabled
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>