BRISTAN TAN 1HBF BLK Tangram 1 Hole Bath Filler User Guide

BRISTAN TAN 1HBF BLK Tangram 1 Hole Bath Filler

Specifications

Pack Contents

Operation

Tools Required for Installation/ Maintenance

Prior to Installation
All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated and receive regular maintenance in accordance with these instructions.
This product needs to be installed in accordance with, and meet the requirements of The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014. For full Installation Requirements & Notes (IRN) please visit www.wrasapprovals.eo.uk/approvals-directory
Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance.
Before installing this product the water supply must be thoroughly flushed in order to remove any swarf, solder etc. Full access must be made available for future maintenance/servicing purposes.
This product must not be modified in any way as this will invalidate the guarantee.

Spare Parts

To replace any spare parts for your tap, why not scan the QR Code or visit www.bristan.com and search for your product.

Important

• The images shown are for illustrative purposes only.
• The tap you have purchased may look different to those pictured in this booklet but will follow the same installation steps.
• Your contents page will be specific to your product.
• If you find your product or any of its components differ from those shown on the contents page, please contact our customer support.

Installation

1. Look underneath the tap body to observe fixing kit rod(s) and tail inlet pos1t1ons
   Depending on the model, the tap will utilise 1 or 2 fixing kit rods. Refer to contents page

2. Screw in the fixing kit rod(s) into the base of the tap with a screwdriver Screw in the flexible tails by hand only.
   DO NOT
   OVERTIGHTEN
   Your model may come with a plinth and will either be included pre-attached or loose in the box*

   • If required, thread the flexible tails and fixing kit rods through the plinth and rubber seal (if loose) and align with tap body
   • Look for any grub screw holes on the plinth as these will need to be aligned with the exposed grub screw on the bottom of the tap

3. Thread the flexible tails and fixing kit rods through the bath hole
   If the hole is not large enough for both tail ends to fit through, unscrew one of the flexible tails and screw back in from underneath the bath

4. From underneath the basin, slide the rubber gasket and metal c plate along the fixing rod(s) with the gasket sitting on top of the c plate

   • Align the gasket and c plate, then begin tightening the nut up the rod towards the bath until secure

5. Connect the hot and cold water supplies to the flexible tails and turn until tight Hot on the left, cold on the right
   Your tap is now ready for use.

6. Your tap is now ready for use.

Maintenance – Cartridge Valve Replacement

Maintenance – Clean Replace Outlet

Housed Outlet
Using an adjustable spanner, unscrew gently to remove the outlet

If your model comes with one, insert the key tool into the outlet and twist to release it

Using a coin, insert into the slot on the outlet and twist to release it

Check all loose parts for any damage, then soak using a suitable solution to de-scale

Reverse the steps to replace the outlet

Love Your Chrome

Bristan offers an effective chrome-friendly cleaning kit for use with your taps and showers. Scan the OR Code or search for ‘CLEAN KIT0l’ on www.bristan.com.

Troubleshooting|
---|---
I| |
Partially closed isolation valve.| Open isolation valve.
I| Airlock or partial blockage in the supply pipework.| Flush through pipework to ensure removal of debris and any airlocks.
No hot water or cycling hot and cold| Partial blockage in the outlet| Remove to Clean and soak in suitable solution.
Instantaneous water heater cycles on and off as flow rate or pressure is too low.| Increase water flow rate or pressure through system
No Flow

Temperatures not corresponding with taps

| Closed isolation valve.| Open isolation valve.|
Mains water supply turned off.
Turn on mains water supply.
Inlet pipes have been connected incorrectly| Swap the inlet tails around.

Notes
Please use this space for any notes you or your installer may have regarding the installation/plumbing of this product.

Contact Us I

BRISTAN
Bristan Group Ltd.

• UK : Bristan Group, B78 lSG.
• EU : Masco Europe S.a.r.l. 14 Rue Strachen
• 6933 Mensdorf Luxembourg

Customer Service : +44330 026 6273

• Web: www.bristan.com
• Email : enquire@bristan.com

A Masco Company

Servicing Your Tap
We recommend servicing your tap at least once every year to prolong its life.
To see a video showing how to remove the cartridge for servicing, scan the QR code with your smart phone or tablet.
Alternatively visit www.youtube.com/BristanTV

BristanTV

Our Guarantee
At Bristan, we want to make things as easy as possible for our customers. That’s why we offer solid guarantees on all our products, effective from the date of purchase, to give you peace of mind.
Your guarantee starts from the purchase of your product, but you can still benefit from registering it for easier identification in the unlikely event of a manufacturing fault, please visit www.bristan.com/register.
For any other queries, please call Customer Service on 0330 026 6273 where our expert team of advisors will be able to offer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service- centre/guarantees.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>