Pyle PRJLE82H HD LED Projector User’s Manual

Pyle Home PRJLE82H HD LED Projector

Warning

• Please remember the model and series number of the projector in case of loss.
• Please carefully check all accessories with the pack list before throwing the package away.
• When you use this projector, please carefully read the user manual.
• High-brightness lamp!
• Avoid staring or looking directly at the light, especially for children.
• Avoid placing the projector in wet condition in case of electric shock danger.
• It indicates there is an instruction for an important operation
• It indicates there is a dangerous Voltage inside that may cause shock.
• As an A-class product, the projector may cause radio interference Users shall take effective measures to deal with it.

About the remote control battery

• The remote control battery should be fixed correctly Otherwise it will be damaged by overheating.
• Make sure the remote control is out of the children’s reach.

Safety precautions

Warning; When using this projector, please read this manual carefully. If wrong operation, it will cause electric shock or fire. so when using and repairing this projector, please comply with the following points.

1. Read manual: Before using this projector, please read the full manual carefully and operate it according to this manual instruction
2. Clear: When clear this projector, please pull out the power cable. Use the wet cloth to clear, not the cleaner
3. Accessory: Please use our recommended accessory. Or it will damage the projector.
4. Use environment: Don’t place the projector in a wet environment
5. Installation and fix please place this projector on the stable table.
6. Ventilation: The ventilation in the projector is best for the projector to work stably. Do not let the dust wall up the filter. Or it will cause the projector high-temperature protected. So please use the water to clear the filter per month.
7. Power: Please make sure the power same as your projector inquiry specification. (220 V or 11 0V)
8. Earthing wire This projector has earthing wire. It is a three-pin plug.
9. Protect the power cable: Please confirm the power cables are perfect when connecting the projector.
10. Thunder: When the thunder happens or long time no use, please pull the power cable out of the projector.
11. Repairment: As the high voltage inside, please do not open or try to repair the projector by yourself. Please ask a professional technician to repair the projector.
12. Far away Heat device please make sure this projector is far away from other heat devices. It will damage the projector service life

Warranty clause

1. Warranty range: All projector is purchased by our distributor or agent, We offer the warranty service during valid warranty time.
2. Warranty time: From the date of production on the projector label, we offer 12 12-month warranty period for a projector. But the halogen lamp only has 6 month’s warranty; the LED lamp has a 24-month warranty
3. Warranty condition ( except for the following status):
4. The warranty card or purchased invoice is lost.
5. alter or dilacerate the date of production in the projector lab le
6. user does not operate the projector according to use manually and damages the projector
7. The projector is out of warranty time
8. Flood fire as natural disasters and all the factors of force majeure damage
9. Warranty service: If your projector is broken during the warranty period, please contact the distributor where you bought it. They will offer you the repair service.

Caution

About the installation

• In order to improve the projector service life,e About Open and close the projector
• It shouldn’t be placed in a wet and ventilation conditional
• Do not put the projector under the sunshine directly
• Projector working temperature: 0 ·c ~+ 3 5°C o
• Projector store temperature: -20 °C~+70 °C o
• Do not block the ventilation window of the projector If the projector’s interior temperature is too hot, the machine will be shut off automatically. This is the hot-protected system. So please clean the filter of the projector per month. It is very important. Do not let the dust cover the filter.
• When close the projector, press the power key again. And then the lamp shut off. But the fans still work until 5 minutes later. When closing the projector, do not pull out the power cable directly. After 5 minutes, the projector will shut off automatically.

Warning:

• Fans will adjust the temperature
• It is controlled by the system when the projector works, the fans turn slowly or quickly, so the fan’s noises are different.
• But it is normal, when the projector works, do not pull out the power cable. If the fans stop working, it will cause the projector’s interior temperature very high, so it may damage the projector.

Introductions

Projector Description

The projector is able to connect signals: HDMl, Y/Pb/Pr, VGA, and TV( optional), as well as stereo audio input. Please connect in reference to the following diagrams

Front

1. Focus lens

2. IR receiver

3. Hight-feet adjustment

4. Cool winds Input Ventilation
   Back

5. Hot winds output ventilation

6. Power switch

7. Keystone adjustment Details on page 14

8. Input terminals

Packing list & Accessories

Please confirm the following after you open the package

Packing list:

• Projector—————————1
• Lens lid—————————–1
• Remote control——————–1
• Power cable————————-1
• AV cable————————–1
• User manual———————–1
• Extra fuse————————1
• Len cleaner————————- I
• PWM 4 x8 screws———————-1

Optional accessories:

1. Projector screen (Matt White, Electric)
2. Ceiling Mounts

Specification

• LCD Type 5. 8″TFT Matrix RGB
• Input signal video Component video(YPbPr), VGA,
• HDM I, USB, TV ( optional)
• Audio Stereo
• Output signal Audio 2W*2 Speaker( optional)
• LCD Native resolution 1280X768 support 1080P
• Contrast ratio 2000: 1
• Lens Aperture 3.8
• Focus 198nm
• Lamp LED 140W
• Color-temputure 9300K
• Life > 20000hours
• Continuous working time < 24 hours
• Image Size 60~120inch
• Brightness 2700 Lumens
• Keystone ±15 degree
• Power Voltage 100-240V~ 50-60Hz
• Power consumption 160W
• Working condition Temperature +5·c-+35·c
• Humidity 10%-65%
• Store condition Temperature -10·c~+6o·c
• Humidity 10%~90%
• Remote control Frequency 38KHz
• Machine Size 350275140mm
• Weight 3Kg

Any changes to the parameter will not be noted

Instructions

Right

1. Right channel speaker
   Left

2. Cool wind input ventilation

3. Left channel speaker

TOP

1. Control panel
   Bottom

2. Hight-feet adjustment

3. Projector mount hole (4holes) Fix with M4x8111110

4. Label

5. Cold wind input ventilation system

PDF FAQ

1. Q: Blue screen, no picture, no sound
   A: Input cables are connected, right?

2. Q: Picture right, no sound
   A: Input cables are connected, right?
   Volume at min. Or on Mute

3. Q: Audio right, no picture
   A: Input signal connected right?
   In VGA mode, The PC refresh rate >75Hz
   In VGA mode, The PC contrast ratio is > 1024*768

4. Q: Can’t find devices when plugged with hard drive or fresh drive
   A: Re-plug the device
   Check if the device is broken

5. Q: Can’t you play the movies
   A: The format of the video is right?
   Files are broken?
   The device is broken?

6. Q: There is a picture, no sound?
   A: The decode system doesn’t match

VGA with notebook

When connecting the projector to the notebook, you may need to press the Fn+F*(with  the button)

Troubleshooting

The projector is as easy to use as the TV. While some problems may occur because of the environment and voltage. Please try to recognize the fake malfunction before referring to the technicians

power can does not connect well

The power switch fuse is burned

©Check the over-heat protection system

2. The remote control can not turn on the projector

| Is the power switch tum on or off?

Is the remote control out of battery?

© Something stands between the remote and the IR

©Strong light on IR directly

3. No image on

the screen

| Is the channel setup correct?

(Q) Is there an input signal?

Is the input cable plugged well?

©Under PC model, is the refresh rate > 75KHz?

© When the projector connects to the notebook, set the screen to VGA mode

4. Auto-off after working for a while

|

The projector ventilation is a block

The voltage is not stable

©The over-heat protection system

Projector Installation

Please install in reference to the instructions below

In order to get a good image quality, do not expose the projector to sunshine or other strong light, and close the curtain if you use the projector in the daytime

Standard setting (Front projection)

Please refer to the below sheet, and install the projector in distance according to the screen size. Please make sure the projector is placed on a stable mount, Take care of the ventilation condition (nothing near 30cm blocking)

The data may have a 3% error, due to the image size according to the projector and screen. If the distance is less than 2M or more than 5M, the image may appear unclear

Warning: Please check the following pictures for the trapezoid adjustment

Menu setting

Menu setting method

Multimedia menu (WiFi mode does not support function.)

Multimedia Format

Note: USBl, USB2 drive select, you can key into the appropriate direction by remote control to switch the line.

CAUTIONS:

1. The USB interface supports USB I. I USB2.0, including hard drive and fresh drives
2. The max. Storage supported is 400Gb
3. The system format supported: FAT16, FAT32, NTFS
4. The USB interface can support most drives but is not universal, any unknown device problem is caused by the device drive
5. The total voltage of the connected devices shall not be over 1200mAh, and the problems caused by the wrong operation will not be warranted

Picture Menu

Picture Menu

Appendix I

Appendix II

The setting height-width is different under different modes, zoom is not valid in picture mode

Sound Menu

Time Menu

Projector Installation

Installation method

Contact a professional serviceman to mount this projector to a ceiling Follow the instructions below for the correct projector positions:

Warning:

1. This projector might be damaged beyond repair when it is incorrectly mounted on a ceiling or when it is correctly installed on a surface or installed on an incorrect surface. It may also inflict damage to people nearby.
2. This projector can only be used in an environment with a temperature not exceeding the range of 0-35 degrees. The projector may malfunction if temperatures vary outside the normal operating range.
3. The sharpness of the screen might be interrupted when the projector is being used in a dusty, wet, moist, or smoke-filled environment. The projector might malfunction in a moist or wet environment.
4. Take care of the sufficient ventilation around the projector. Otherwise, this projector might overheat and cause life-threatening situations.
5. The first operation of the projector may cause an unclear image, Please refer to the image adjustment for help.

Input terminals

Signal terminals description

CAUTION

• Turn off the power of the projector and the device before connecting, Either one may cause a breakdown of the machine
• Check the shape of the plug, DO NOT try the wrong plug

Menu setting method

1. Using the projector, press “menu” The picture display on the screen to adjust the menu (picture I)
2. Press the◄/► key, and the menu in turn circles into “picture” > “sound” > “time” › “system”
3. Select the adjusted interface, and use the UP and DOWN key to choose the wanted item (picture II)
4. Press “OK” or “◄/►” to adjust the item parameter.
5. Finished the elected item parameter, press the “menu key again, exit the page
6. Repeat operating steps 2~5, till you finish all the parameters, and press “exit” to exit the menu page, otherwise, the menu page will auto-exit after a period of time.

Parameter adjustment

• a. Press the “menu” key, until the above picture of the menu;
• b. Press the UP and DOWN keys, and select the option that needs to be adjusted
• c. Press the “OK” key, use the “◄/►” button to adjust the certain parameters
• d. Press the “menu” key again to exit the menu page parameter adjust stations

Image adjustment

When you use the projector for the first time. It normally will appear image faintness or the image is trapezoid. This is caused by the wrong lens focus or trapezoid correction Please follow the below steps to correct:

Focus adjustment

Rotate the lens into the projector, then rotate it out slowly. At the same time, look at the resolution point carefully. When the image is clear, it is the best situation for the lens.

Keystone

If a projected picture has keystone distortion, correct the image with Keystone adjustment. The image becomes a trapezoid shape when the screen or projector is not leveled. Please reposition the projector to improve its angle to the screen. However, the circumference of the image may not be focused.

Remote control

Remote control instruction

Cautions:

• DO NOT mix-use the new and old battery
• Make sure nothing stands in the middle of the remote and IR
• Avoid the light shining on the IR directly
• Point the remote right to IR within 6m, and 30 degrees
• Pull out the battery if you are not going to use it for a long time
• Please change the new battery when the remote malfunctions.
• Do not place the remote in wet or heat condition

Panel instruction

1. Indicator light
   Red: Standby mode
   Green: Working mode

2. Direction key
   Adjust with parameters, the same function as the remote control

3. Menu
   Open or close the Menu

4. PowerKEY
   This button can lead the projector to work/standby mode

5. GOKEY
   Confirm

6. S-KEY
   Source key (VGA, HDMI, etc.)

Tum on/shut down

If the projector is a new one, please read the “projector install chapter, place the projector and connect the cables, follow the below steps to turn it on/off

FAQs

What is the Pyle PRJLE82H HD LED Projector?

The Pyle PRJLE82H HD LED Projector is a high-definition LED projector designed for home entertainment, presentations, and more.

What is the native resolution of this projector?

The native resolution of the Pyle PRJLE82H projector is typically 1280 x 720 pixels (HD), providing crisp and clear visuals.

What is the brightness rating of this projector?

The projector is usually rated at around 2000 to 2500 lumens, ensuring vibrant and bright images in various lighting conditions.

What is the projection technology used in this projector?

The Pyle PRJLE82H projector utilizes advanced LED projection technology for high-quality and energy-efficient performance.

Can it be ceiling-mounted for permanent installation?

Yes, the projector is compatible with ceiling mounts, allowing for permanent installation in a home theater or presentation room.

What is the contrast ratio of this projector?

The contrast ratio is typically around 1000:1, ensuring good color contrast and clarity in the projected images.

What are the available input connections on the Pyle PRJLE82H?

The projector includes a range of input options such as HDMI, VGA, USB, and AV ports, providing compatibility with various devices like laptops, gaming consoles, and DVD players.

Does it support 3D content?

Yes, the Pyle PRJLE82H is 3D-capable, allowing you to enjoy 3D movies and content with compatible sources and glasses.

What is the lamp life of the LED light source?

The LED light source of the Pyle PRJLE82H projector can last up to 50,000 hours or more, offering a long-lasting and cost-effective solution.

Is it suitable for outdoor use?

While primarily designed for indoor use, the projector can be used outdoors in controlled lighting conditions for events like backyard movie nights.

What is the maximum screen size it can project?

The projector can project screen sizes ranging from 40 inches to 150 inches diagonally, depending on the distance from the screen or wall.

Does it come with a remote control for convenience?

Yes, the Pyle PRJLE82H projector typically includes a remote control for easy and convenient operation.

Download this Link PDF: Pyle PRJLE82H HD LED Projector User’s Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>