JBC Tools GSFR Guide Kit for Robot Instruction Manual
- June 13, 2024
- JBC Tools
Table of Contents
www.jbctools.com
INSTRUCTION MANUAL
GSFR
Guide Kit for Robot with/without
Solder Wire Perforation
GSFR Guide Kit for Robot
This manual corresponds to the following references:
GSFR[XX]V[LL]-B With Solder Wire Perforation – described on page 8 of this
manual.
GSFR[XX]D[LL]-B Without Solder Wire Perforation – described on page 9 of this
manual.
Tube Length
Wire Diameter
Packing List
Guide Kit for Robot with Solder Wire Perforation
The following items are included. See Exploded View (page 8) for references.
Manual …………………………………………………. 1 unit
Ref. 0030637
Guide Kit for Robot without Solder Wire Perforation
The following items are included. See Exploded View (page 9) for references.
Packing List
Features
The Guide Kit GSFR is designed to be used with the Solder Feeder SFR in automatic soldering processes.
Assembly: GSFR Wheels to SFR
For this operation, disconnect the device, and take off the cover by pressing
the tabs.
Use the Allen key and the spanner provided with SFR for the following steps.
First disassemble the guide tube (6), the Support and Traction wheels or the
Guide Wheel, Blade and Bade Clamp (4)+(5).
Then, disassemble the nozzles (2)+(3). Disassemble the Counter Wheel (1).
Assembly with Solder Wire Perforation
- Assemble the counter wheel (1).
- Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
- Assemble the inlet nozzle (3) and tighten the screw.
- Assemble the guide wheel (4) and tighten the screw. Attention: Always use the correct wheel set for each wire thickness.
- Assemble the blade first, then mount the blade clamp (5) onto the same axis and tighten the screw. Caution: handle the blade carefully to avoid injury.
Assembly without Solder Wire Perforation
- Assemble the counter wheel (1).
- Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
- Assemble the inlet nozzle (3) and tighten the screw.
- Assemble the support wheel (4) and tighten the screw. Attention: Always use the correct wheel set for each wire thickness.
- Assemble the traction wheel (5) onto the axis and tighten the screw.
Assembly: GSFR Tube to SFR and TRA
- Assemble SFR to TRA with the screws.
- Assemble GSFR Guide Tube to TRA and tighten the screw.
- Assemble the Outlet Nozzle onto the Dispensing Tube.
- Assemble GSFR Bushing into SFR hole and tighten the screw
- Finally attach the Reel Support to SFR with its screw.
Solder Wire Loading
GSFR must be assembled previously.
- Feed the Solder Wire into the Inlet Nozzle until it reaches the wheels.
- Make sure the wire passes through the Intermediate Nozzle and enters into the Guide Tube.
Important: Set the wire thickness parameter before starting to dispense the wire. To set W-THI command see the Communication Protocol for SFR unit at www.jbctools.com/jbcsoftware.html. Wire feeding is controlled by an external controller (Robot/PLC/Computer). To start wire loading process use W-SLD command. See the Communication Protocol for SFR unit at www.jbctools.com/jbcsoftware.html
Maintenance
- Before carrying out maintenance, always unplug the tool and the device.
- Use a damp cloth to clean the tool. Alcohol can only be used to clean the metal parts.
- Periodically check that the metal parts of the mechanism are clean.
- Keep Dispensing Nozzle Tip clean to avoid solder feeding obstruction.
- Periodically check all cables and tube connections.
- Replace any defective or damaged parts. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.
Safety
It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.
- Do not use the device for any other purpose.
- Be sure that the power supply is disconnected before changing any spare part.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful of fumes produced while soldering.
- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves while handling components to avoid personal injury.
- Utmost care must be taken with liquid tin waste which can cause burns.
Exploded View
Notes
Specifications
GSFR
Guide Kit for Robot with/without Solder Wire Perforation
Ref.: GSFR[XX]V[LL]-B With Solder Wire Perforation (Ref. described on page 8
of this manual)
Ref.: GSFR[XX]D[LL]-B Without Solder Wire Perforation (Ref. described on page
9 of this manual)
– Total Net Weight: 42 g / 0.093 lb
– Total Package Dimensions / Weight: 245 x 185 x 45 mm / 117 g
(L x W x H) 9.65 x 7.28 x 1.77 in / 0.258 lb
Complies with CE standards.
ESD safe.
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labor.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage
paid, to the dealer where it was purchased.
Get 1 extra year JBC warranty by registering here
:https://www.jbctools.com/productregistration/ within 30 days of purchase.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must be collected and returned to an authorized recycling
facility.
References
- JBC Soldering Stations, Irons and Rework equipment for electronics
- JBC Soldering and Rework equipment for electronics
- JBC Software
- Warranty Extension
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>