CHiQ CRSR125DB Retro Bar Fridge User Manual
- June 13, 2024
- CHiQ
Table of Contents
- CHiQ CRSR125DB Retro Bar Fridge
- Product Information
- Product Usage Instructions
- PART NAMES AND LOCATIONS
- IMPORTANT SAFETY INSTRUCTIONS
- Door reversal instruction
- HANDLE INSTALLATION
- INSTALLATION INSTRUCTIONS
- OPERATING INSTRUCTIONS
- GENERAL CARE AND MAINTENANCE
- TROUBLESHOOTING
- Customer Service
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CHiQ CRSR125DB Retro Bar Fridge
Product Information
The Retro Bar Fridge, model CRSR125DB, is a compact refrigerator designed for cooling beverages and snacks. It features a chill compartment door, thermostat for temperature control, glass shelf,crisper cover, crisper, adjustment foot, door pocket rack, and door bottom rack. The fridge uses R600a flammable refrigerant in its sealed system.
Product Usage Instructions
- Ensure proper ventilation by keeping the appliance’s ventilation openings clear of obstruction.
- Do not use any mechanical devices or means to accelerate the defrosting process other than those recommended by the manufacturer.
- Avoid damaging the refrigerant circuit.
- Only use electrical appliances inside the food storage compartments if they are of the type recommended by the manufacturer.
- Do not store explosive substances, such as aerosol cans with flammable propellants, in the appliance.
- When disposing of the appliance, take it to a recycling center for safe recycling. Do not dispose of it in a landfill as the insulation and refrigerant gas are flammable.
- For door reversal, refer to the provided instruction manual.
- To install the handle, follow the provided handle installation instructions and use the included bolts and Allen key.
- If applicable, follow the provided instructions for installing or disassembling the bottle opener using the included bolts.
- Before using the refrigerator, refer to the installation instructions provided.
PART NAMES AND LOCATIONS
No | Description |
---|---|
1 | Chill compartment Door |
2 | Thermostat |
3 | Glass Shelf |
4 | Crisper Cover |
5 | Crisper |
6 | Adjustment foot |
7 | Door Pocket Rack |
8 | Door Bottom Rack |
IN ACCESSORY BAG: USER MANUAL, WARRANTY CARD
As the manufacturer holds the authority to redesign or modify its products
without notice: Any modifications or upgrades of our products will result in
this refrigerator varying slightly from this manual but the functionality will
remain the same to that as set out within this manual.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Follow these basic precautions to reduce the risk of fire, electrical shock hazards or injury when operating the refrigerator:
- This product has been designed for use in a normal domestic environment. It is not intended for commercial use which will avoid warranty, such as supermarkets, food shop, pharmacies, commercial kitchens & etc.
- Persons with lack of experience and knowledge of reduced physical or mental capabilities, need to be given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- It is critical use this appliance safely. Read all instructions before operating the refrigerator and do not attempt to repair or modify this unit in any way as it can cause harm or void the warranty.
- Please ensure all persons using this appliance are also informed and comply with the details set out within this manual and the product Terms and Conditions.
- When unpacking the appliance for the first time, keep all cardboard and plastic packaging out of reach from children.
- Report any notable defects with the appliance to Chiq or retailer as soon as it is noted. Failure to do so can result in a non-warranty claim. Keep all packaging materials in a safe location until the unit has been installed properly.
- If the supplied power cord of this unit is damaged, it must be replaced by qualify service agent or similarly qualified persons in order to avoid any risk of injury. It is recommended the power cord is situated in a safe location when operating or transporting the appliance to prevent any damage that may cause electrical shock or fire hazards.
- DANGER or WARNING:
Service of this unit
The installation or any service of the appliance is recommended by a qualified technician or service company.
Ventilation Hazards
Never clean the refrigerator or refrigerator parts with flammable fluids, or store gasoline or any other flammable vapors and liquids in the vicinity of this or any other refrigerator as the gas and/or vapour can cause a fire hazard, explosion or inhalation.
Electrical Connection
Make certain, when installing or moving the unit that the power outlet has been connected to, has been fitted by a qualified electrician and the ground wire has been connected properly to meet the Australian Electrical Standards.
R600a WARNINGS
NOTE: This model uses R600a flammable refrigerant in its sealed system.
The following must be observed for your safety:
R600a Refrigerant Warning
- This appliance contains 0.023kg R600a refrigerant which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect.
- During transportation and installation, ensure that the tubing of the refrigerant circuit is not damaged.
- Leaking refrigerant can ignite and may damage the eyes.
- In the event any damage does occur, avoid exposure to open fires and any device that creates a spark. Disconnect the appliance from the main power.
- Thoroughly ventilate the room in which the appliance is located for several minutes.
- Notify Customer Service for necessary action and advice.
- The room for installing the appliance must be at least 1 cubic metre per 8 grams of refrigerant. The refrigerant quantity contained in this appliance is listed above in grams; it is also noted on the Rating Plate of the appliance.
- Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
It is hazardous for anyone other than an Authorised Service Person to carry
out servicing or repairs to this appliance. In Queensland, the authorized
person must hold a Gas Work Authorisation for hydrocarbon refrigerants, before
carrying out servicing or repairs which involve the removal of covers.
1. Keep ventilation openings, in the appliance enclosure or in the built-in
structure, clear of obstruction.
2. Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recommended by the manufacturer.
3. Do not damage the refrigerant circuit.
4. Do not use electrical appliances inside the food storage compartments of
the
appliance, unless they are of the type recommended by the manufacturer. 5. Do
not store explosive substances such as aerosol cans with a flammable
propellant in the appliance.
Disposal
The environment and personal safety must be considered when disposing of this
appliance. Please ensure the appliance is taken to a recycling center for safe
recycling. DO NOT dispose of the appliance in a landfill as the insulation and
refrigerant gas contained in these appliances are flammable.
Door reversal instruction
If the appliance is placed on its back or side for any length of time during this process, it must be allowed to remain upright for 6 hours before plugging it in to avoid damage to the internal components.
- Remove the plastic hole cover located on the top left side of the refrigerator as shown in Fig. 1. Remove the upper hinge cover and the upper hinge on the right side of the refrigerator, as shown in Fig. 2.
- Remove the door from the lower hinge pin by pulling it gently upwards. Remove the lower hinge bracket on the right side of the unit and remove the leveling foot on the left side. Reverse their positions as shown in Fig. 3.
- Install the lower hinge on the left side of the refrigerator. Install the adjustable foot on the right side of the refrigerator as shown in Fig. 4.
- Move the door bushing to the left and the plastic hole cover to the right as shown in Fig. 5.
- Remove the door stop from the lower right sideof the refrigerator door. Install the door stop on the lower left side of the refrigerator door as shown in Fig. 6.
- Install the upper hinge and hinge cover on the left side of the unit. Place the plastic hole covers in the holes on the right side of the top of the refrigerator to cover the screw holes as shown in Fig. 7.
Note: When installing the door, ensure that the top of the door is level with the top of the cabinet. If the door is not level, the rubber gasket will not make a good seal with the cabinet which can cause the appliance to malfunction.
HANDLE INSTALLATION
Door handle packing list
Parts Name| Qty
Handles| 1
Bolts A1| 2
Bolts A2| 2
Alan key| 1
Installation:
- Step1: Install two pair of Bolts A1 into the fridge and freezer door, Use a Phillips screw drive to tighten them properly.
- Step2. Put and hold the handle on the bolts and secure the bottom grub screws with the Alan key which is supported. Please note the grub screws have been installed in the handle
Bottle opener installation and disassembly
Bottle opener packing list
Parts Name| Qty
Bottle opener| 1
Bolts B1| 3
Installation:
- Step 1: Install three Bolts B1 into freezer, Use a Phillips screw drive to tighten them properly.
- Step2.: When removing the bottle opener, use a Phillips screwdriver to remove the bolts
INSTALLATION INSTRUCTIONS
Before Using the Refrigerator
-
Remove the exterior and interior packing.
-
Before connecting the refrigerator to a power source, let the unit stand upright for approximately 6 hours to mitigate the possibility of a malfunction in the cooling system from improper handling during transportation.
-
Clean the interior surface with warm water using a soft cloth.
Installing the Refrigerator -
This appliance is designed to be free-standing only, and should not be recessed or built-in.
-
Allow at least 5cm of space between the back and sides of the refrigerator to allow proper air ventilation. Insufficient space will result in cooling and working life issue and voiding warranty.
-
Place the refrigerator on a leveled/even floor surface that is strong enough to support the weight of the refrigerator when it is fully loaded to prevent vibrations.
-
Place the refrigerator on a concrete, tile floor or waterproof floor is recommended. The fridge will produce defrost water or condensation moisture, it might cause water damage in some extreme circumstances.
-
The front feet can be adjusted to level the appliance properly. Adjust the two front feet to keep the refrigerator leveled or elevated.
-
Situate the refrigerator away from direct sunlight and sources of direct heat (stove, heater, radiator, etc.). Direct sunlight may also affect the acrylic coating and heat sources may cause an increase power consumption.
-
This unit is not designed for outside installation.
-
Avoid situating the refrigerator in moist OR pest infestation areas.
-
Plug the refrigerator into a dedicated, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized service center.
-
After plugging the appliance into a wall outlet, turn the unit on and allow the unit to cool down for 4-6 hours before placing food in the refrigerator.
-
Do not place heavy items on the top of this appliance.
ENERGY SAVING TIPS
- Allow hot foods to cool to room temperature before placing in the refrigerator. Overloading the refrigerator forces the compressor to work harder. Foods that freeze too slowly may lose quality, or spoil.
- Be sure to wrap foods properly, and wipe containers dry before placing them in their refrigerator. This cuts down on frost build-up inside the refrigerator.
- Organize and label food to reduce door openings and extended searches. Remove as many items as needed at one time, and close the door as soon as possible.
OPERATING INSTRUCTIONS
Temperature Control
- “OFF” shows a forced STOP and “7” shows the coldest temperature. Turn the knob from “1” position to “7” position, the temperature setting decreases continuously.
- Set the knob to “4” position in normal use. But it can be adjusted to the setting that best suits your needs.
The marks on the knob are the temperature grades, not the exact number of degrees of temperature.
Defrosting
The appliance isn’t a frost frost-free model and it needs to manually defrost
regularly. When the refrigerator works for a period of time, the top chill
compartment will be covered with a layer of thick ice. It may increase the
power consumption and reduce the cooling efficiency. Please do a manual
defrost when ice is thicker than 10mm or the door can’t be closed properly due
to too much ice. When defrosting, cut off the power, open the door and remove
food to a shady cooling place, wait for 2 or 3 hours, let the temperature rise
naturally till ice gets soft or melts. Then wipe away ice and water.
Notes: Please only use a plastic scraper to remove ice if required. Never
use sharp metal tools as it might damage the gas pipe which will avoid
warranty
There is a drip tray under the chill compartment, it will collect water from the chill compartment. Please empty the tray regularly to avoid overflow.
Notes
- Please note different sections of the refrigerator compartment may be warmer or cooler than others – typically the top back wall will be the coolest, the door rack will be the warmest. To avoid frost bite, please don’t put raw vegetables too close to the chill compartment.
- Large quantities of food stored in the appliance or directly in front of the air vent will hinder the cooling efficiency of the appliance as this can affect the airflow.
- Change the thermostat settings and allow 6 hours for the temperature to stabilize between adjustments.
- Do not keep opening and closing the door which will increase the temperature in the unit.
CHANGING THE LIGHT
- The LED lamp is used by the refrigerator for lighting, which features low energy consumption and long service life. In case of any abnormality, please contact the aftersales personnel for visiting service.The LED lamps can only be replaced by the aftersales personnel
GENERAL CARE AND MAINTENANCE
Cleaning the Refrigerator
- Upon installation of your new appliance, it is recommended that it be cleaned thoroughly and properly maintained thereafter.
- Turn off the refrigerator and then unplug the unit from the wall outlet.
- Remove all food content before washing the inside with a damp cloth soaked in lukewarm water and dishwasher liquid. Don’t use any chemical detergent which might damage the fridge.
- Be sure to keep the door gasket (seal) clean to keep the unit running efficiently as improper cleaning can cause the seal to dislodge and tear.
- Dry the interior and exterior with a soft cloth.
Vacation Time
- Turn off the refrigerator first and then unplug the unit from the powerpoint.
- Remove all food.
- Clean the refrigerator.
- Leave the lid open slightly to avoid possible formation of condensation, mold, or odors.
- Use extreme caution in the case of children. The unit should not be accessible to children’s play.
- Short vacations: Leave the refrigerator operating during vacations of less than three weeks.
- Long vacations: If the appliance will not be used for several months, remove all food and unplug the power cord. Clean and dry the interior thoroughly. To prevent odour and mold growth, leave the door open slightly: blocking it open if necessary.
Repositioning and Relocating the Refrigerator
- Unplug the power cord from the wall outlet.
- Remove all the food and drinks.
- Securely tape down all loose items inside your refrigerator.
- Tape the doors to be closed securely.
- It is recommended that the refrigerator stays in the upright position during transportation. But if it is laid down for transport purpose, please lift it up immediately after the job is done. Please wait for at least 24 hours before putting the power.
TROUBLESHOOTING
Problem
| ****
Solution
---|---
The fridge has no power
| ****
The power cord isn’t plugged in properly.
Ø The circuit breaker tripped or a blown fuse.
Ø Try a different power point.
The light is not working.
| Ø There is no light in the freezer compartment, only the fridge compartment has light.
Ø Make sure the power is connected to the unit.
Compressor runs all the time
| ****
Ø The room temperature is hotter than normal.
Ø A large amount of food has been added to the refrigerator.
Ø The door is opened too often.
Ø The door is not closed completely.
Ø The temperature control is not set correctly.
Ø The door gasket does not seal properly.
Ø The refrigerator does not have the correct clearances.
Ø The refrigerator has recently been disconnected for a period of time. 6+ hours are required for the refrigerator to cool down completely pending on operating conditions.
The temperature inside the refrigerator is too warm.
| ****
Ø Temperature control is set incorrectly. Turn the control to a cooler setting and allow several hours for the temperature to stabilize.
Ø Door is kept open too long or is opened too frequently. Warm air enters the refrigerator every time the door is opened). Open the door less often.
Ø The door is not closed completely.
Ø The door gasket does not seal properly.
The temperature inside the refrigerator is too cold.
| ****
Ø Temperature control is set too cold. Turn the control to a warmer setting and allow several hours for the temperature to stabilize.
The temperature of the external refrigerator side walls are warm.
| ****
Ø The exterior refrigerator walls can be as much as 15-20 degrees warmer than room temperature.
This is normal while the compressor works to transfer heat from inside the refrigerator cabinet to the condenser behind the refrigerator side walls.
Popping or cracking sound when the compressor comes on.
| ****
Ø Metal parts undergo expansion and contraction, as in hot water pipes. This is normal. The sound will level off or disappear as the refrigerator continues to run.
|
---|---
Bubbling or gurgling sound, like water boiling.
| ****
Ø Refrigerant (used to cool refrigerator) is circulating throughout the system. This is a normal operation.
Leaking water on the bottom of the fridge compartment
| ****
Ø The drain hole might be blocked by food particles, please clean the hole and unblock it with a flexible metal wire.
Vibrations.
| ****
Ø Check the refrigerator is on a level/even surface.
Ø Refrigerator rocks on the floor when it is moved slightly. Be sure the floor can adequately support the refrigerator.
Ø Level the refrigerator by putting wood or metal shims under part of the refrigerator.
Ø The refrigerator is touching the wall. Re-level the refrigerator and move it from the wall. See “Installation Instructions”.
Moisture forms on inside refrigerator walls.
| ****
Ø Weather is hot and humid, which increases the internal rate of frost build- up. This is normal.
Ø Door is slightly open.
Ø Door is kept open too long or is opened too frequently. Open the door less often.
Ø The door is not sealed properly.
Moisture forms on the outside of the refrigerator.
| ****
The door is slightly open, causing cold air from inside the refrigerator to meet warm moist air from the outside.
The doors will not close properly.
| ****
Ø The refrigerator is not on a level surface.
Ø The gasket/s may be dirty or not properly maintained. Clean the seals and make sure they are dry before closing the door/s.
Ø The storage basket and/or shelves are out of position.
For any inquiries, please call CHiQ Customer Care on: 1300 796 688
Customer Service
- 1300 796 688
- www.chiq.com.au.
- Changhong Electric (Australia) P/c L all rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>