CHiQ WTL80W 8kg Top Load Washing Machine User Manual

USER MANUAL
MODEL WTL80W WTL79B
AUTOMATIC WASHING MACHINE

PLEASE READ CAREFULLY THIS USER’S MANUAL BEFORE USING YOUR WASHER AND SAVE THIS FOR FUTURE REFERENCE.

PACKING LIST

Automatic washing
machine| User’s manual| Water inlet hose set
(Coldwater)| Water inlet hose set (Hot water)| Bottom plate
---|---|---|---|---
1 set| 1 copy| 1 pcs| 1 pcs| 1 pcs
| | | |
screw| Drain hose| Hose clamp|
1 pcs| 1 pcs| 1 pcs
| |

SPECIFICATIONS

SAFETY INSTRUCTIONS

Please note that the following precautions for safety intend to prevent unpredictable danger and damage by helping the proper use in safety.
When using hot water in washing, please make sure that the water should not exceed 50°C.
Plastic parts may be deformed or damaged, and an electric shock or a fire may take place.

WARNING There might be serious injury or fatal accident when you violate those instructions.
If the power supply cord or plug is damaged or loosened, do not use. ” An electric shock or a fire may take place.
Do not pull the cord off or touch it with moist hands. ” An electric shock or a fire may take place.
Do not bend the power supply cord by force or press it with heavy things. ” An electric shock or a fire may take place.
Do not install the washer nearby an electric implement or don’t put a candlelight or cigarette light on the washer. ‘ Afire may take place.
Do not disassemble, repair or remodel it recklessly. When you need to repair it, please call the service agent. * An electric shock or a fire may take place.
During operation, do not put your hands or metal materials under the washer. ” You may be hurt by the spinning board beneath the washer.
Stay away from the washer when the bottom of the washer sinks into the water. “‘ There might be an electric shock. Please wait until the water drains out completely.
Do not put laundry stained with gasoline, or benzene. or alcohol in the washer, and keep the materials away from the washer. ” An explosion or a fire may take place.
During spinning, don’t put your hand in the spinning tub. ” It may hurt your hand. If it does not stop within 15 seconds after you open the lid, call the service agent immediately.
CAUTIONS There might be slight injury or damage when you violate those instructions.
Do not install it in an area with moisture or outdoors where it has rain or snow. – An electric shock or a fire may take place.
Please unplug the power supply cord when you do not use it. ‘ An electric shock or a fire may take place.
If there is dust or water on the power supply plug and its connected part, please remove it completely. An electric shock or a fire may take place.
Do not make your kids look into the inside of the washer. ‘ If your kid falls into the washer, his life could be in danger.
Ventilate immediately without touching the power plug if the gas is leaking. ” An exploding or a fire may take place if gas catches flame.
If the washer makes a strange noise, smell or smoke, unplug it promptly and call a service agent. “‘ An electric shock ana a fire may take place.
When cleaning, do not spray water to the parts of the washer directly. ” It may make its life span shorten. . Also, an electric shock or a fire may take place.
Do not use several appliances together with an outlet. A fire may take place due to unusual heat.
Do not press the button with an awl or pin. An electric shock or a fire may take place.
Use the new water inlet hose-sets and old hose-sets should not be reused.
If damage is found on the power cord in use, it should be replaced by the manufacturer, service agent or authorized person. An electric shock may take place.
The power receptacle must be grounded properly. An electric shock or a fire may take place.
DESCRIPTION OF PARTS
The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.

INSTALLATION

The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.
> ENVIRONMENT
Leave some space
Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface
If the washer is placed on an uneven or weak surface, noise or vibration
occurs. (Max. tilt angle on the supporting surface: 2°)
Adjust the legs for even placement
Never install the washer near the water
Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation causing an electrical shock hazard.
Avoid direct sunlight or heater
As plastic and electrical components are affected by direct heat, never place the washer near furnaces, boilers, etc. Do not place the washer under direct sunlight. > ASSEMBLING THE BOTTOM PLATE

1. Place the washing machine on the soft laying cloth, the front side of the machine is towards the upper.
2. Insert the bottom plate into the slots on the base under, and then tighten it with a screw.

LEVELING THE WASHER

• If the washer is not leveled with the ground, it makes the machine tremble more or be out of order.
  So, make sure that the washer is leveled properly.
  @ SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB
• Open the lid of the machine, pour water into the tub up to the level just below the pulsator, and adjust the adjustable feet so that the pulsator is positioned at the center of the water as shown in the figure.
  ADJUST THE INSTALLATION POSITION
  If the floor is uneven, adjust the adjustable feet of the washing machine to a level position.
  Lift the adjustable feet up slightly and turn the feet to a level position.
• The distance between the washing machine and the wall: at least 10cm.
• Max. tilt angle on the supporting surface: 2°.

> ATTENTION 
+ When installing the machine, it needs to remove two of the packing parts, including base packing and tub support as shown in the figure. Otherwise, the washing machine will not run normally.

• During the installing the washer or in the first using the washer, there may be some water flowing out of the drain hose, which is the residual water at the step of inspection by the factory.
• After washing, be sure to pull off the power plug, close the water faucet, avoid an electric shock or a fire to take place, and avoid water leakage to take place. POWER SUPPLY

Before plugging the power cord plug into the wall receptacle, check the voltage rating is in the range of the rating, marked on the label at the back side of the washer.

> GROUNDING

• If your water faucet or water pipe is not made of metal, connect the ground wire to a copper plate or a metal rod and bury it in the earth.
  

• If both your water faucet and water pipe are made of metal, connect the ground wire to the base of the water faucet.

• It is of no use connecting the ground wire to the water pipe made of plastic.

• In the case of using a 3-core cord, there is no need for grounding.

NEVER CONNECT THE GROUND WIRE TO SUCH A THING

• Never connect it to a gas pipe because of a lightning rod because of very dangerous at thunderbolts.

• Never connect it to a telephone wire or danger of an explosion.

Be careful not to confuse the hot water inlet (pink color) and cold water inlet (blue color), if your washer is provided with dual water inlets. Also if you have only one water tap, connect the inlet hose with the cold water inlet (blue color).
> CONFIRMING THE WATER FAUCET
Water faucet type, as shown in the right figure:
TypeA: This type is suitable. It is a special faucet for washer use.
Type B: This type is suitable. It is required that the front end of the faucet shall be longer than 10mm. The exit end surface of the faucet must be flat and smooth. Otherwise, it may leak water. Please file the end surface to avoid leakage.
Type C: This type of faucet is not suitable, there may be a leakage in the place shown in the figure. If the water faucet is not suitable, it is needed to replace a suitable water faucet before connecting the water supply hose. > CONNECTION THE WATER SUPPLY HOSE

Connect the other end of the water supply hose to the inlet water valve at the back of the washer. Screw the hose clockwise all the way in.

plan B

1. Remove the adaptor from the water supply hose

2. First, use a “+” type screwdriver to loosen the four screws on the adaptor. Next, take the adaptor and turn part (b) following the arrow for a gap of about 5mm between them.

3. Connect the adaptor to the water tap by tightening the screws firmly. Then, turn part (b) following the arrow and put part(a) and part(b) together.

4. Connect the water supply hose to the adaptor. Pull down part (c) of the water supply hose. When part (c) is released, the hose is automatically connected to the adaptor making a *click’ sound.

NOTICE:

• After completing the connection, if water leakage from the hose, then repeat the same step.
• Use the most suitable type of faucet for water supply.
• If the end of the faucet is square or too big, please loosen the four screws and take out the bushing in the adaptor before inserting the end of the faucet into the adaptor.

LEAK TEST
Turn on the water completely to check for any leakage. If there are any leakage, turn off the water supply, try again as the above procedures.
For the special tap, call a qualified plumber for the installation.
DRAIN HOSE SETTING
The User’s Manual is for common use.
Make use of the User’s Manual depending on your washing machine model.

• Connect the drain hose to the drain outlet at the side of the washer, and fasten it tightly with the hose clamp supplied.

• The washer should be installed in its final position such that the drain hose is not kinked or trapped.

• The corrugated drain hose should be inserted into a suitable drain pipe of between 50cm and 85cm height above the floor using the curved drain hose support, the minimum inner wide or diameter of the drain pipe should be 4cm.

• If an under-sink connection is used the drain hose must be routed above the sink overflow vent to prevent siphoning.

• The drain hose should not be submerged in the water to prevent siphoning.

• Care must be taken to avoid kinking or trapping the drain hose.

• The drain hose must be fixed reliably to avoid leaks or spills .

CHECKING BEFORE WASHING AND CARING FOR GARMENTS

Must follow the checkpoints in order to avoid machine problems or damage on garments
 If the below problems are caused by the customer’s faults, a separate service fee will be charged.
Checkpoints Before Starting Washing
Check if the clothes are bleaching or not.
Add liquid detergent to a white towel and the garment where you can’t notice well. Then. rub together strongly. Check if the color transferred to the towel.
Be careful for scarves and imported clothes since they are easily discolored.
Check for stains or partial dirt.
**If stains are found, use the towel wet with detergents to rub on in a single direction.
Before washing, the sleeves, collar, dress hem and pockets are pre-treated by brushing with detergents.
The wrinkle-processed clothes made of wool are specially treated by fixing them with threads before washing them. The threads should be removed after the clothes are dried./
Not Washable Laundry
Clothes that are easily transformable even by soaking in water.
Even by soaking in water, neckties, brassieres, jackets, suits and coats can be easily transformed like shrinking and discoloring on the garment surfaces because they are mostly made of rayon, polynosic, cuff, and their blend fabrics.
The wrinkle-processed, embossed, or resin-processed products are easy to transform even by soaking in water.
Easily discoloring products made of cotton and wool, wrinkled silk, leather products, leather accessory, leather ornamented clothes and its accessory.
Do not wash those clothes without handling guidelines or material indication tag.
About Detergent
When detergents are not dissolving well, use warm water (about 40°C) to dissolve the detergent.
Caution
** Use an appropriate amount.
  Even if an excess amount of detergent is used, there is not much more difference in washing result. It may cause damage to the garments because rinsing is not enough.
The bleaching agent may cause damage to garments since it is strong alkali.
Do sufficient rinsing because the powder detergent is easily remained on the garments causing bad odors.
  If too much detergent is used or cold water is used, it doesn’t dissolve completely and remains on the garments, hose or inner tub, causing contamination on clothes.
In case of reserved washing, detergents must be put in the detergent box. If the powder detergents are spread on the laundry directly, it may cause discoloration.

CARING FOR CLOTHES BEFORE WASHING

Must follow the checkpoints in order to avoid machine problems or damage on garments.
If the below problems are caused by the customer’s faults, a separate service fee will be charged.
Take out personal belongings from pockets.
Caution. Check the pockets! Hairpins and coins may cause damage to clothes and washing machines.
They may make noise and problems to the machine. Must check the pocket.

CHECKING BEFORE WASHING AND CARE FOR GARMENTS
  pants zippers are open while washing, the inner tub may be damaged. The zipper should be closed and fixed with a string before washing.
  If blue jeans and working uniforms zippers or hooks are made of steel, they must be closed before washing.

Wash winter jumpers, working uniforms, bed cover sheets, and blue jeans separately.
Fold clothes well into the inner tub. Must remove the curtain hooks before washing.
Turn inside out the button decorated and embroidered clothes before washing.
  Be careful with those metal decorations because they may cause heavy damage while washing.
The long stringed clothes may tangle with other clothes. Must fix the strings before washing.

The metal strings from brassieres may stick out and damage other clothes or the inner tub. Must use the commercial laundry net for washing brassieres. (Use a laundry net of fine mesh.)
Waterproof clothes ( Ski Wear, Diaper Covers, Footboards) are not allowed for washing.
The waterproof sheet, clothes, and nonwater permeable fabrics shouldn’t be washed, rinsed, or put in the inner tub. The laundry may pop out and cause severe vibration so that a person may get damaged and the machine, wall, and floor may break out in addition to the clothes.
(Examples are diaper cover, waterproof wear, raincoat, umbrella cover, ski wear, car sheets, and sleeping bags.)
Cautions During Spinning
Spinning of regular garments
–The water from garments is drained out through the inner tub holes.
© Spinning of waterproof clothes and fabrics
–Even if the inner tub spins, water can’t drain out from the waterproof clothes and fabrics.
Therefore, water gathers to one side and this causes a severe vibration. If the inner tub spins at a high speed, water still can’t drain out from the waterproof clothes and fabrics. As a result, garments move up and pop out with a big vibration.
Shake the dirt or soil from clothes.
  Soil and sand may rub delicate garments to cause damage and the washing result may be unsatisfactory.

For the protection of baby skin
Wash diapers and baby wears ( baby clothes, baby towels, etc ) separately. Dirt may get to baby’s clothes from adult’s clothes if washing them together.
Do pre-washing for white socks, sleeves, and collars before the main washing
  Use powder and liquid detergents.
Do not use soap. It may leave dirt to the inner tub.

CHECKING BEFORE WASHING AND CARING FOR GARMENTS
Turn inside out for those nappy clothes before washing.
If clothes have too much foreign matter, separate them for washing. Other clothes may pick up those dirty matters (diet, thread).
**** Wash black-colored clothes and cotton towels separately. If they are washing together, towels may pick up dirty matters. Check before washing.

Cashmilon and those garments having big volume and lightweight(eg. lace- decorated clothes, ligerie, nylon stocking, synthetic fabrics etc.) may rise and cause damage to the clothes and problems to the machine. Use the laundry net or wash them separately.
Must put those long stringed clothes, lace-decorated clothes, bed cover sheets, wool clothes into a laundry net before washing.
Put delicate clothes in the laundry net.

Use only those commercial laundry net for washing Curtains, floating garments or biue jeans shall be pressed not to float on the water
If they are floated on the water, press Start/Pause button to stop and press them to sink in the water. If the washing goes on with clothes floating on the water, it may cause damage to the clothes and washing machine as well as unsatisfactory washing results.

CONTROL PANEL

For more details, see the control panel of your washing machine

1. POWER BUTTON
   Press this button once operate.
   Press once again to turn the power off.

2. START/PAUSE BUTTON
   Itis used to pause and restart the operation.

3. WATER TEMPERATURE SELECT BUTTON
   As you press this button, the type of water is selected as fellow: COLD- HOT—-WARM—COLD, select the needed one of the water temperature conditions (cold, warm, hot}, corresponding water temperature light will shine.

4. ONE-TOUCH BUTTON
   «When POWER Button is not pressed, continue pressing this button over 3 seconds, the washer run the ONE TOUCH program, the ONE TOUCH light shines at the same time.
   + Firstly press the POWER button, then continue to press this button for over 3 seconds, the washer starts to run the ONE TOUCH program, the ONE TOUCH light twinkles at the same time.
   + Firstly press the POWER button, secondly press this button, select ONE TOUCH program, then press the START/ PAUSE button, the washer start to run ONE TOUCH program, the ONE TOUCH light shines at the same time.

5. PROGRAM BUTTON
   With every press of this button, the washing program changes.
   Daily-Quick-Gentie-Heavy Duty-Cotton-Bedding-Spin-Tub Clean

6. WATER LEVEL SELECT BUTTON

• According to the wash-load, with every press of this button, select the water level, the corresponding water level date shows in the digital tub:
  1-+2-3-+-4-§-6 7-8-1
  + Continue pressing this button for over 3 seconds, and you can set the washer delay start time, with every press this button, set delay start time.
  control panel
  For more details, see the control panel of your washing machine
  
  

  7. DIGITAL TUB
     « When the washer starts to run, the digital tube shows the remaining time (in minutes) of each wash cycle. —
     For example, The residual time is 18 minutes, the digital tub shows:
     + When the washer has some faults, the digital tub shows the FailureCodes.
     For example, Spinning do not work, and the digital tub shows:
     «When having set the washer delay start time, the digital tub shows the date of selecting delay start time.
     For example Delay start time is 4 hours. the digital tub shows:

  8. WATER TEMPERATURE AND FUNCTION INDICATOR LIGHT
     + Shows three water temperature conditions, after pressing WATER TEMP. button to select the water temperature condition, the corresponding light shines.
     « Shows washer on CHILD-LOCK condition. after selecting the CHILD-LOCK function, the CHILD-LOCK light shines.

  9. PROGRAM INDICATOR LIGHT
     After selecting the wash program, the corresponding program light shines.

HOW TO WASH AUTOMATICALLY DEPENDS ON THE LAUNDRY

• > BEFORE STARTING WASHING, CHECK THE FOLLOWING:
  Connect the water supply hose to the water tap. Leave a tap open. Plug the power cord in. Make sure to set the drain hose well.

WASHING FOR THE FIRST TIME
Before washing clothes for the first time, you must run a complete cycle without clothes. To do this:

1. Press the POWER button.
2. Pour a little detergent into a detergent box or the inner tub.
3. Turn on the water supply faucet to the washing machine.
4. Press the PROGRAM button, and select TUB CLEAN program.
5. Press the START/PAUSE button.

PUT IN THE LAUNDRY

• The capacity of washing and spinning of the washer refers to the largest dry weight of the load that can be washed or spun in one time. One-time washing quantity shall be lower than the rated capacity.
• The thickness, size, and type of clothes will influence the actual capacity. It is suitable for one-time washing to put In a reasonable amount of laundry and the laundries can be turned round in the washing

HOW TO PUT THE DETERGENT IN

1. Open the detergent box by pulling in the direction of the arrow as shown in the figure and then put the powder detergent In the detergent box.
2. Put in a one-time amount of detergent evenly so the detergent may not brim over the box.
3. If there is not detergent box in the washing machine, please pour the detergent into the inner tub directly.

SPECIAL NOTES
Automatic Sensing Function

• At every program, the amount of laundry is automatically sensed and then the appropriate water level, washing time, rinsing cycle, and spinning time are automatically selected for automatic washing.
• After the power is on, a program is selected and the START/PAUSE button is pressed. Then, the pulsator starts spinning without water, this action senses how much laundry is in the tub. not a machine problem. After this sensing process, water supplies automatically. Some programs do not have this function.

Adding detergent

• it senses the amount of laundry and Indicates the water level. Then, it starts the water supply right away.
• During the water supply. it is possible to open the detergent box and add detergent. However, it is better to press the START/PAUSE button to stop the water supply and add detergent. Close the lid and press the START/PAUSE button again. This way is much more convenient. Put the laundry into the washer and add detergent, too.
• Be careful not to overload. Use right detergent for the laundry you are washing.
• If the lid is open while running, the washing machine will be stopped automatically for safety. (Except, the water supply continues while the lid is open.)
• Possible to control the water level at every program during the washing.

WASHING PROCEDURE
Before starting washing, check the following:
Connect the water supply hose to the water faucet. Leave the faucet open. Plug the power cord in. Make sure to set the drain hose well.
Put the laundry into the washing machine and add detergent, too.
Be careful not to overload. Use the right detergent for the laundry you are washing.
> ONE-TOUCH PROGRAM
Selects the best washing program automatically.

1. Press the POWER button.

2. Press the ONE TOUCH button.
   The ONE TOUCH program light shines.

3. Press the START/PAUSE button.
   The water level is selected automatically. Washing, rinsing, and spinning follow. if you want to pause, press the START/PAUSE button again.

4. Close the lid.

EIGHT PROGRAMS

1. Press the POWER button.

2. Press the PROGRAM button In turn.
   Select one of the eight programs(Daily, Quick, Gentle, HeavyDuty, Cotton, Bedding,Spin, Tub Clean),the corresponding program light shines.

3.  Press the START/PAUSE button.
   The water level is selected automatically. Washing, rinsing, and spinning follow. If you want to pause, press the START/PAUSE button again.

4. Close the lid.

DELAY START function
Select the DELAY START function when you have to go out or do something else.

1. Press the POWER button.

2. Press the PROGRAM button.**program**
   Select the needed program.

3. Continue to press the WATER LEVEL button over 3 seconds.
   Go into the DELAY START selecting model, you may change the delay start time with press the WATER LEVEL button (from 0 hours to 24 hours), the delay start time shows in the digital tub.

4. Press the START/PAUSE button.

5. Close the lid

The washing cycle will start by the time you reserved.

WASHING PROCEDURE

CHILD-LOCK function: This is a device to protect children from being accidentally hurt while playing with the washer How to start the Child-Lock function:

1. Press the POWER button

2. Press the PROGRAM button To select an initial washing program.**PROGRAM**

3. Press the START/PAUSE button Start the washing program.

4. Close the lid
   If the Child-Lock function is needed during the laundry.

5. Press both the “Water Level” and “Program” buttons at the same time Get the Child-Lock function to start, the CHILD-LOCK function light shines.

(Note: You can not perform the function without the “Power” button on.)
To release the function of Child-Lock: – In case the “Child-Lock” is programmed, press both the “Water Level” and “Program” buttons at the same time to release the function of Child-Lock.

MANUAL FUNCTION

Each washing program can be changed manually. you can change two of the items (the water level and water temperature).
WATER LEVEL and WATER TEMPERATURE function

1. Press the POWER button.

2. Press the PROGRAM button. To select an initial washing program.**PROGRAME**

3. Select the water level or water temperature
   3.1. Press the WATER LEVEL button Select the needed water level, and the corresponding water level date ( from 1 to 8 >1) shown in the digital tub. 3.2. Press the WATER TEMP button
   Select the needed one of the water temperature conditions (cold, warm, hot), corresponding water temperature light shines.

4. Press the START/PAUSE button.

5. Close the lid The washing program will run based on the functions you have selected.

MAINTENANCE

The User’s Manual is for common use. Make use of the User’s Manual depending on your washing machine model.
Proper care of your washer can extend its life. This section explains how to care for your washer properly and safely.
> CLEANING YOUR WASHER

interior with the appropriate
cloth or sponge as they occur. Occasionally wipe the outside| amount of detergent. Run
of your washer to keep it looking like new.| washer through the
During cleaning your washer.| -TUB CLEAN° program.
•Do not flush it directly with water.| Repeat the process if necessary.
•Wipe it with neutral detergent.|
•Do not wipe it with thinners, petrol,
alcohol or other harsh solvents.|

> WINTER STORAGE OR MOVING CARE
Install and store your washer where it will not freeze. Because some of the water may stay in the hoses, the freeze may damage your washer. If storing or moving your washer during freezing weather, winterize it.

•Shut off the water faucet.
•Disconnect water inlet hoses.
•Run the washer on a DRAIN and SPIN program for 1 minute.
•Unplug the power supply cord.| •Flush water pipes and hoses.
•Recombination water inlet hoses.
•Turn on water faucet.
•Recombination power supply cord.

NON-USE OR VACATION
Operate your washer only when you are at home. If you will be on vacation or not using your washer for an extended period of time, you should:

• Unplug the power supply cord or turn off the electrical power to the washer.
• Turn off the water supply to the washer. This helps avoid accidental flooding (due to a water pressure surge) while you are away.

CLEAN THE LINT FILTER

Clean the lint filter often to keep your washer clean.

CLEANING THE WATER INLET FILTER

> CLEANING THE DRAIN FILTER

•  In the case “U” shape drain hose, this drain filter is equipped at the back side of the washer.
• This drain filter is to screen foreign stuff such as threads, coins, pins, buttons, etc.
• If the drain filter is not cleaned at the proper time (once a month). Drian’s problem could be caused.
• Do not clean the drain pump filter when there is water in the bucket; if there is an E3 alarm, it is necessary to put down the drain pipe to drain all the water first, and then clean the drain pump filter.

ERROR CODES

Spinning does not work
Is the laundry spread out evenly in the washer?
Is the washer installed on a sturdy and flat surface?
If the washer does not spin, a buzzer will sound, and the digital tub will show “El”.

> Water is not supplied s the water tap opened?
Is the water supply cut off?
Is the water supply hose or hose connection filter clogged?
Is the water supply hose frozen?
Is the pressure of water supply too lower? s the water Inlet timeout?
( water is not supplied, a buzzer will sound, and the digital tub will show “Er.

> Water does not drain
Is the drain hose down? (No pump) Is the drain hose frozen?
Is the drain hose clogged? Is the height of the end of the drain hose over 15cm?(No pump) If water does not drain, a buzzer will sound, and the digital tub will show “E3”.

Washing machine won’t work
Is the lid open?
If the lid Is open, the washer won’t work, a buzzer will sound, and the digital tub will show “E4”.

> Washing machine won’t work or does not drain
Is the CHILD-LOCK function set and the lid open?
If the CHILD-LOCK function is set and the lid is open, the washer won’t work or does not drain, a buzzer will sound, and the digital tub will show “EL”. > Other problem If the digital tub shows “EA” or “EC”, Please press the POWER button, cut off the power, and pull off the power plug. call the service agency immediately.

TROUBLESHOOTING

Most problems are easily solved if you understand the cause. Check the following list for problems before calling for service. Before calling for service, check this> The power is cut off.
Check1> Is the electric voltage normal?
Check2> Is the power plug of the washer plugged In the receptacle? Insert the power plug into the receptacle.
> The washing machine does not drain?
Check This the drain hose down? (No pump) Put the drain hose down.
Check 2>is the drain hose folded? Unfold the drain hose.
Check 3>is the drain hose outlet clogged?
Remove the clogging matters cleanly.

The washing machine doesn’t work
Check 1>is the washer lid open? Close the lid.
Check 2>Has the START/PAUSE button been pressed? + Press the START/PAUSE button one more time and check if the washer starts.
Check 3>ls enough water filled to the water level? If the water pressure is low. it takes a long time to start washing.
Check 4>ls the faucet closed + Open the faucet to supply water.
The water leaks at the supply hose connector.
Check 1> If the faucet connecting part is loose, water may leak. + Repeat the assembly steps again (Refer to ‘Connecting the water supply hose).
Check 2> Check if the rubber packing of the water supply hose is in the right position. Screw tightly again.
Check 3> Is the water supply hose folded? ••• Unfold the hose.
Check 4> if the water supply Is too strong, water may leak.
*Close the faucet a little.*
Check 5> Is water leaking from the faucet itself?
• Reassemble the faucet again, or replace the faucet. > Water is not supplied.
Check 1> Did you press the START/PAUSE button after selecting the water supply?
• If the START/PAUSE button Is not pressed, water is not supplied. Press the START/PAUSE button.
Check 2> Is the faucet closed? Turn on the faucet.
Check 3> is the filler net at the water supply hose connector clogged with dirty matters? Clean the filter net by brushing with a toothbrush.
Check 4> Is the water supply cut off? if the water supply is suspended, turn off the faucet and power off.
> Spinning makes loud noises and vibrations.
Check 1> Check if the laundry is spread evenly in the washer. Spread out the laundry evenly and start again.
Check 2> Check if the washing machine levels on a sturdy flat floor. Set the washer at the level.
Check 3> Is the washing machine filled with unnecessary stuff?
▪ Remove those unnecessary things away from the washing machine. > These cases are not malfunctions
• The sound “wing” heard during the water supply is the operating sound made by the water inlet valve.
• The sound ‘she heard in the stopping step of the inner tub is the sound that comes from the liquid moving in the balance ring in the inner tub.
• the sound -hu-lo” heard during the drain cycle is the sound of the drain pump operating.
NOTE!** If the power supply cord is damaged, it must only be replaced by a repair shop appointed by the manufacturer, because special-purpose tools are required.

Customer Service
1 3 0 0 7 9 6 6 8 8
www.chiq.com.au
Changhong Electric (Australia) P/L all rights reserved.

References

• CHiQ

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>