Roam-ON R10 MiFi 4G LTE WiFi Mobile Hotspot Router User Manual
- June 13, 2024
- Roam-ON
Table of Contents
R10 MANUAL
ROAM-ON R10 APPEARANCE
PRECAUTIONS
Please read the following precautions before using:
- Handle with care, device should be kept cleanly.
- Do not put in place with wet, water or other liquids.
- Do not put in place of extremely high or low temperatures.
- Do not put near flame or lit tobacco.
- Do not drop, throw, bend or demolish.
- Do not put or install on top of car airbags.
- Altitude: 5 2000 meters, the power adapter determines the applicable altitudes for using.
- Ambient Temperature: device can be normally used at the temperature of -10 °C ∼ 60 °C.
NETWORK STANDARDS
- Support multi-bands of LTE FDD, bands of 2,4,5,12,17,26 & LTE TDD, bands of 41
- Support HSPA + / UMTS (2100MHz / 1900MHz / 1700MHz (AWS) / 900MHz / 850MHz)
- Maximum downstream rate 150Mbps
- Maximum upstream rate 50Mbps
- Maximum rate 300Mbps
- Support 802.11 b/g/n/a/ac
- Support band 2.4G/5.0G
- Support simultaneous connections for 5 devices
BATTERY
Battery Capacity High-capacity lithium battery of 5000mAh
Charging Voltage DC 5V 2A
Full Charging 4 hours required
Battery Life Standby for 24 hours. In using for 12 hours. Please charge
first if not prolonged used.
Note-1 The ambient temperature should be 0 °C – 45 °C; 20% battery
capacity would be lost after normal using for one year.
Note-2 Do not over charge or discharge, users are highly recommended to:
recharge every 2 months if not in used.
FUNCTION DESCRIPTION
Power Button Long press the power button for 3 seconds to power on/off,
short press to wake up device or switch screen. *Reset Device: Long press
Power Button for 15 seconds to reset & restart when Roam-ON device can’t be
turned off properly.
Micro SIM Card Slot Insert SIM / USIM card here.
Input Charging Port Charge device through data cable.
Screen Display of Roam-ON R10 device information, network connection
status, etc.
SCREEN
Interactive screen will be displayed after network successfully connected:
- Signal strength
- Network type (UMTS / H / H+ / LTE)
- Battery icon (means it is in charging)
- Country in using
- Traffic used today
- Number of connections
Short press the power button to switch to the second screen:
INSTRUCTIONS
How to Connect to Roam-ON:
- Reserve Internet Service To ensure internet access, please reserve internet service on Roam-ON.com
- Connect Network After power on, Roam-ON takes 2-3 minutes to connect and access to the preferred local network. Connecting details will be displayed in the screen.
- Surf Internet With Roam-ON R10 device on, short press the power button, WiFi hotspot name(SSID) and password(PWD) will be displayed in the screen, connect your smart phone or pad to Roam-ON network by input password to start surfing Internet.
SIM CARD SETTING
Roam-ON R10 provides a second using mode by enabling SIM Card, setting as follows:
-
As shown in the figure below, insert SIM Card under the power off status of Roam-ON R10 device.
-
By wireless connecting your Internet Equip-ment to Roam-ON R10 mobile hotspot. Set APN details from http://192.168.1.1/apn_set.html
-
Roam-ON R10 hotspot name(SSID) and password(PWD)
-
Roam-ON R10 version, if SIM Card inserted, the screen will display “SIM in using”
R10 4G
Documents / Resources
|
Roam-ON R10 MiFi 4G LTE WiFi Mobile Hotspot
Router
[pdf] User Manual
R10, R10 MiFi 4G LTE WiFi Mobile Hotspot Router, MiFi 4G LTE WiFi Mobile
Hotspot Router, 4G LTE WiFi Mobile Hotspot Router, WiFi Mobile Hotspot Router,
Mobile Hotspot Router, Hotspot Router, Router
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>