MC17J8100CS_AA 1.7 cu. ft. Capacity Smart Over the Range Microwave

Product Information

The Over The Range Microwave Oven is a kitchen appliance that is
designed to be installed above a range or cooktop. It provides a
convenient way to cook, heat, and defrost food items. The microwave
oven weighs 69 pounds and has a maximum total weight capacity of
109 pounds, including additional oven loads.

Important Safety Instructions

– This product requires a three-prong grounded outlet. Ensure
that the power outlet box is properly grounded by performing a
ground continuity check before installation.

– Before starting the installation, remove the house fuse or
open the circuit breaker to avoid the risk of severe or fatal shock
injury.

– The mounting surface must be strong enough to support the
weight of the cabinet load, the microwave oven (69 pounds), and any
additional oven loads (up to 50 pounds).

– This product cannot be installed in cabinet arrangements such
as an island or a peninsula. It must be mounted to both a top
cabinet and a wall.

Electrical Requirements

Ensure that the electrical requirements are met before
installing the microwave oven. Follow the guidelines provided in
the electrical requirements section of the user manual.

Hood Exhaust

The microwave oven offers different ventilation types for hood
exhaust:

• Outside top exhaust (vertical duct)
• Recirculating (non-vented ductless)
• Outside back exhaust (horizontal duct)

Damage – Shipment/Installation

Inspect the product for any damage caused during shipment or
installation. If any damage is found, refer to the user manual for
instructions on how to handle the situation.

Parts Included

The package includes all the necessary parts for installation.
Refer to the user manual for a complete list of parts and their
descriptions.

Tools You Will Need

Gather the following tools before starting the installation:

• List of required tools

Mounting Space

Ensure that you have sufficient space for mounting the microwave
oven. Refer to the user manual for detailed information on the
required mounting space.

Product Usage Instructions

Step-by-step Installation Guide

1. Placement of the Mounting Plate: Follow the
   instructions in the user manual to remove the microwave oven from
   the carton and locate the mounting plate. Find the wall studs and
   determine the wall plate location under your cabinet. Align the
   wall plate properly.

2. Ventilation Types: Choose a ventilation type
   (outside top exhaust, recirculating, or outside back exhaust) based
   on your requirements. Follow the installation procedures provided
   in the user manual for the chosen ventilation type.

3. Installation: Prepare the rear wall for
   outside back exhaust, attach the mounting plate to the wall, use
   the top cabinet template to prepare the top cabinet, and mount the
   microwave oven. Connect the ductwork for outside top exhaust.

4. Before Using Your Microwave: Review the
   instructions in the user manual before using your microwave
   oven.

For detailed step-by-step instructions and illustrations, refer
to the user manual provided with the product.

Installation Instructions
Over The Range Microwave Oven

BEFORE YOU BEGIN (Read these instructions completely and carefully.)
IMPORTANT Save these instructions for local inspector’s use.

IMPORTANT Observe all governing codes and ordinances.

· Note to Installer

– Be sure to leave these instructions with the Consumer.

· Note to Consumer – Keep these instructions for future reference.

· Skill level

– Installation of this appliance requires basic mechanical and electrical skills.

· Proper installation is the responsibility of the installer.

· Product failure due to improper installation is not covered under the Warranty.

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 1

2020-04-13 12:02:05

Contents
General information
Important safety instructions . . . . . . . 3 Electrical requirements . . . . . . . . . . 3 Hood exhaust . . . . . . . . . . . . . . . . 4 Damage – Shipment/Installation. . . . . . 6 Parts included . . . . . . . . . . . . . . . 6 Tools you will need . . . . . . . . . . . . . 7 Mounting space. . . . . . . . . . . . . . . 7

Step-by-step installation guide
1. Placement of the mounting plate . . . . 8
A. Removing the microwave oven from the carton/Removing the mounting plate . . 8
B. Finding the wall studs. . . . . . . . . . . 8
C. Determining wall plate location under your cabinet . . . . . . . . . . . . . . . . . . 9
D. Aligning the wall plate. . . . . . . . . . 10
2. Ventilation types (choose a, b or c) . . . 11
A. Outside top exhaust (vertical duct) . . . 12 A1. Installation procedure for exhaust adaptor and proper damper operation check . . . . . . . . . . . . . . . . 12 A2. Adjust the exhaust adaptor . . . . 12
B. Recirculating (non-vented ductless) . . 12 B1. Adapting the microwave blower for recirculation . . . . . . . . . . . . 12 B2. Installing the charcoal filter . . . . 13
C. Outside back exhaust (horizontal duct) 14 C1. Adapting the microwave blower for outside back exhaust . . . . . . . 14
3. Installation . . . . . . . . . . . . . . . . 15
A. Preparing the rear wall for outside back exhaust . . . . . . . . . . . . . . . . . 15
B. Attach the mounting plate to the wall . 15
C. Use the top cabinet template to prepare the top cabinet . . . . . . . . . . . . . 16
D. Mount the microwave oven . . . . . . . 16
E. Connecting ductwork for outside top exhaust . . . . . . . . . . . . . . . . . 17
4. Before you use your microwave . . . . 18

2
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 2

2020-04-13 12:02:05

General information

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury.
CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load and the added weight of this 69 pound product, plus additional oven loads of up to 50 pounds or a total weight of 109 pounds.
CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.
NOTE: For easier installation and personal sIanfseurtey,priotpiesr recommended that two people ingbsreoftouarneldluteshxeiisstsproduct.
IMPORTANT ­ PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.

InInsusruerperoppreorper ggrorounudnedxiestxsists bbeefofroereuseu.se

The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.

You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded.

If you have a standard two-prong wall receptacle, it is very important to have it replaced with a properly grounded threeprong wall receptacle, installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

ELECTRICAL
REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 14.6 amps and 1.75 kilowatts.This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate branch circuit single grounded outlet of at least 15 A and max of 20 A. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.

3
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 3

2020-04-13 12:02:06

General information

HOOD EXHAUST
NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 11.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart contains an example of one possible ductwork installation.

DUCT PIECES

EQUIVALENT LENGTH

x

NUMBER USED

=

EQUIVALENT LENGTH

Roof Cap

24 ft.

x

(1)

=

24 ft.

12 Ft. Straight Duct (6 Round)

12 ft.

x

(1)

=

12 ft.

Rectangular-toRound Transition Adaptor*

5 ft.

x

(1)

=

5 ft.

Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.

Total Length =

41 ft.

• IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart contains an example of one possible ductwork installation.

DUCT PIECES

EQUIVALENT LENGTH

x

NUMBER USED

=

EQUIVALENT LENGTH

Wall Cap

40 ft.

x

(1)

=

40 ft.

3 Ft. Straight Duct (3 ¼ x 10 Rectangular)

3 ft.

x

(1)

=

3 ft.

90 ° Elbow

10 ft.

x

(2)

=

20 ft.

Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.

Total Length =

63 ft.

NOTE: For back exhaust, care should be taken to align the exhaust with the space between studs, or the wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate the exhaust duct.

4
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 4

2020-04-13 12:02:06

General information

Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully.
NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate with a standard 3 ¼ x 10 rectangular duct.
If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6 diameter duct.

Maximum duct length:
For satisfactory air movement, the total duct length of 3 ¼ x 10 rectangular or 6 diameter round duct should not exceed 140 equivalent feet.
Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow
and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the equivalent length in feet of some typical ducts.

DUCT PIECES
Rectangular-to-Round Transition Adaptor*

EQUIVALENT LENGTH
5 ft.

x

NUMBER USED

=

EQUIVALENT LENGTH

x

( )

=

ft.

Wall Cap

40 ft.

x

( )

=

ft.

90 ° Elbow 45 ° Elbow 90 ° Elbow

10 ft.

x

( )

=

ft.

5 ft.

x

( )

=

ft.

25 ft.

x

( )

=

ft.

45 ° Elbow

5 ft.

x

( )

=

ft.

Roof Cap

24 ft.

x

( )

=

ft.

Straight Duct 6 Round or 3 ¼ x 10 Rectangular

1 ft.

x

( )

=

ft.

Total Ductwork =

ft.

• IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using tin snips, in order to allow free movement of the damper.

Equivalent lengths of duct pieces are based on actual tests and reflect the requirements for good venting performance with any vent hood.

5
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 5

2020-04-13 12:02:06

General information
DAMAGE – SHIPMENT/INSTALLATION
· If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.
· If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. · If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by
arrangement between the customer and installer.

PARTS INCLUDED

HARDWARE PACKET

PART

QUANTITY

Wood Screws (¼ x 2)

1

Toggle Bolts

(and wing nuts)

3

(3/16 x 3)

Self-aligning

Machine Screws

3

(¼ – 28 x 3 ¼)

You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts.

NOTE: Some extra parts are included.

ADDITIONAL PARTS

TOPCABINETTEMPLATE TOPCABINETTEMPLATE REARWALLTEMPLATE REARWALLTEMPLATE

PART Top Cabinet Template
Rear Wall Template

QUANTITY 1 1

Installation Instructions

1

Exhaust adaptor

1

GREASE FILTER
You can find the grease filter that is installed on the product or just packed with the product. Please check the shape of your grease filter and install the grease filter on your product correctly.

PART

QUANTITY

Separately Packed Grease Filters

2

6
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 6

2020-04-13 12:02:07

TOOLS YOU WILL NEED

General information

1 and #2 Phillips screwdriver

Pencil

Ruler or tape measure and straight edge

Carpenter square (optional)

Tin snips (for cutting damper, if required)

Scissors (to cut

Electric drill with 3/16, ½ and

template, if necessary)

drill bits

Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only)

Gloves Level

Saw (saber, hole or keyhole)

Stud finder or Hammer (optional)

Duct and masking tape

Safety goggles

MOUNTING SPACE

12 max.
16 ½ 30 5

30 min.

Bottom edge of the cabinet needs to be 30 or more from the cooking surface.

Backsplash

NOTES:
· The space between the cabinets must be 30 wide and free of obstructions.
· This microwave oven is for installation over ranges up to 36 wide.
· If you are going to vent your microwave oven to the outside, see the Hood Exhaust Section for exhaust duct preparation.
· If installing the microwave oven beneath smooth flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance.
· Maximum cabinet depth above and beside the unit is 12.
· The dimensions provided are the minimum required for mounting the microwave oven. Local codes and the practical use of the range will likely require you to provide more than the 13.5 shown between the range and the bottom of the microwave.

7
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 7

2020-04-13 12:02:07

Step-by-step installation guide

1. PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE
1. Remove the installation instructions, Exhaust adaptor, filters, glass tray, and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven.
2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
CCaarrtotonn

SSttyyrorofofoaamm

3. Pull the carton up and off the oven.

4. Remove and properly discard plastic bags.

SSccrreewwss

SSccrreewwss

MMoounnttininggPPlatlae te

B. FINDING THE WALL STUDS
WWaallllSStutdusds
CCeenntetrer
1. Find the studs using one of the following methods: A. Stud finder­a magnetic device which locates nails. OR B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location.
2. After locating the stud(s), find the stud’s center by probing the wall with a small nail to find the edges of the stud. Then, place a mark halfway between the edges. The center of any adjacent studs should be 16 or 24 from this mark.
3. Draw a line down the center of the studs. THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.

5. Remove the 2 screws from the mounting plate. This plate will be used as the rear wall template and for mounting.
6. Replace the two screws you removed and carefully screw them back into the case. DO NOT OVER-TIGHTEN. If you over-tighten the screws, you can strip the screws and damage the case.

8
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 8

2020-04-13 12:02:07

Step-by-step installation guide

C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate position ­ beneath flat bottom cabinet.

Plate position ­ beneath framed recessed cabinet bottom.

16 ½

CL At least 30

Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the cabinet and the centerline on the template lines up with the line you drew on the wall.

PPllaatetepposoistioitnio­nb­enbeeatnheraetchesrseecdebsostetodmbcoatbtoinmet with fcroanbtinoveetrwhaitnhg.front overhang
DDrraaww aa hlionreizoonnttahleline to mark how far the inside odbdfeaetscphcktehewnforadoflsnlthtebeqoeuvfloreaowrlnhttotahntehge coavbeirnheatn. g.

CL 303 0to” tCooCookotkotopp

C

L

30 to Cooktop

Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the cabinet frame and the centerline on the template lines up with the line you drew on the wall.

Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
Draw a vertical line on the wall at the center of the 30 wide space. Draw a second, horizontal line on the wall below the cabinet to mark how far the inside of the front overhang descends below the cabinet. Tape the Rear Wall Template onto the wall so that the top of the template touches the bottom of the horizontal line and the centerline on the template lines up with the vertical line.

9
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 9

2020-04-13 12:02:08

Step-by-step installation guide
D. ALIGNING THE WALL PLATE

HHooleleAA

CCeenntteerrllininee nnoottcchheess

DDrraw a VHeorrtizcoalnLtainleline on tooohfnfe”TWRwoepaaallCllrfaarWoblomiannlelgCtTetehnmetepbrloattteo”.m

HoHroizrioznontatal lLLiinnee AArrea E

CL
HHoolle B Hoorriizzoonntatal Ll iLniene DDrraawwaaHHoroizroiznotanltlainlelionnewoanll wfroamll fbrootmtom of “Rear bWoatltloTmemopflat”eR”.ear Wall Template”.

CAUTION: Wear gloves to avoid cutting fingers on sharp edges.
1. Draw a Horizontal line on the wall at the bottom of the “Rear Wall Template”.
2. Drill holes for toggle bolts in 3 locations (Hole A, Hole B, Hole C) as shown in the illustration above. If the location of a hole lines up with a stud, drill a 3/16 hole for a wood screw. You cannot use a toggle bolt to attach the wall plate to a stud.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.

3. Holes A, B and C are inside area E. If none of these holes line up with a stud, find a stud in area E that lines up with a hole circle in Area E, and then drill a 3/16 hole into it for a wood screw. You must have at least one wood screw mounted firmly into a stud to support the weight of the microwave. Set the mounting plate aside.

10
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 10

2020-04-13 12:02:08

Step-by-step installation guide 2. VENTILATION TYPES (CHOOSE A, B OR C)

This microwave oven is compatible with the following three types of ventilation:
A. Outside Top Exhaust (Vertical Duct) B. Recirculating (Non-Vented Ductless) C. Outside Back Exhaust (Horizontal Duct)

NOTE: This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). An exhaust adaptor is shipped assembled and attached to the filler-upper. Select the type of ventilation required for your installation and proceed to that section.

A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)
AAddaappttoorrininPPlalcaece fEfToooxrrhpOOaEuuustxtstshidiadeueTsot p

B. RECIRCULATING (NONVENTED DUCTLESS)

See page 12

See page 13 A Charcoal Filter Accessory Kit is required for the nonvented exhaust. (See your Owner’s Manual for the kit number.)
C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

See page 14

11
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 11

2020-04-13 12:02:08

Step-by-step installation guide

A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)
A1. INSTALLATION PROCEDURE FOR THE EXHAUST ADAPTOR AND PROPER DAMPER OPERATION CHECK
Damper

NOTE: You must attach the house duct to the exhaust adaptor after installation is complete.
HHoouusseeDDuucct t

Blower Plate

Exhaust Adaptor

Retaining Hooks

Back of Microwave Oven

1. Slide the exhaust adaptor as shown in the diagram above.
2. Make sure the tape securing the damper is removed and damper pivots easily before you mount the microwave.
CAUTION: You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.

A2. ADJUST THE EXHAUST ADAPTOR

After you have installed the microwave, you will need to open the top cabinet and adjust the exhaust adaptor so that you can connect it to the house duct.

Damper

Back of Microwave Oven

For Side-toSide Adjustment, Slide the Exhaust Adaptor as Needed

B. RECIRCULATING (NON-VENTED DUCTLESS)
B1. ADAPTING THE MICROWAVE BLOWER FOR RECIRCULATION
1. Remove and save screw that holds blower plate to microwave.
2. Lift up the blower plate.
Blower Retaining Screws
Back of Microwave Oven
NOTE: The exhaust adaptor with the damper is not needed for recirculating models. You may want to save them for possible future use.

12
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 12

2020-04-13 12:02:09

Step-by-step installation guide

3. Remove the screw that holds the blower motor and carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.

7. Close the blower door. Slide blower shield onto the top of the blower door opening.

CAUTION: To avoid breaking or cracking the blower blade, do not touch the blade. Hold the outer case of the blower when you pull it out or put it back in place.

4. Roll the blower unit 90° so that the fan blade openings are facing toward the front of the microwave.

Before Roll

After Roll

5. Place the blower unit back into the opening.
CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. 6. Remove the metal vent fan cover on the back of
the microwave by sliding it up.

8. Secure the blower to the microwave using the blower retaining screws from Step 1.
Blower Retaining Screw
Blower Retaining Screws
Back of Microwave Oven
B2. INSTALLING THE CHARCOAL FILTER
1. Remove the screws on the top of the grill using a #1 Phillips screwdriver.
2. Open the door. 3. Remove the grill. · Push the grill left, and then pull the grill straight
off.
Charcoal filter
4. Install the charocal filter. When properly installed, the wire mesh of the filter should be visible from the front.
5. Reinstall the grill and the screws. 6. Close the door.

13
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 13

Insert mesh-side up 2020-04-13 12:02:10

Step-by-step installation guide

C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

C1. ADAPTING THE MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST
1. Remove and save the screws that hold the Blower Plate to the microwave.
Blower Retaining Screws
Back of Microwave Oven
2. Open the blower door by lifting it up at the back of the microwave. Remove and save the blower shield on the back of the microwave by sliding it up. Remove and save the metal vent fan cover on the back of the microwave by sliding it up.
3. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.
BEFORE: Fan Blade Openings Facing Forward
End B
End A
CAUTION: To avoid breaking or cracking the blower blade, do not touch the blade. Hold the outer case of the blower when you pull it out or put it back in place. 4. Remove Parts “A” with tin snips or pliers.
Parts “A”

5. Rotate the blower unit counterclockwise 180 °.

Before Rotation

After Rotation

Back of Microwave

Back of Microwave

6. Place the blower unit back into the opening.
AFTER: Fan Blade Openings Facing Back
End A

End B

CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should match exhaust openings on the rear of microwave oven.
7. Close the blower door. Slide blower shield onto the top of the blower door opening. Secure the blower to the microwave oven using the blower retaining screws from Step 1 except the upper blower motor retaining screw.
Blower Retaining Screw
Blower Shield
Blower Retaining Screw
Back of Microwave Oven
8. Slide the exhaust adaptor onto the back of the microwave oven, securing it into the lower locking tabs. Take care to ensure that the damper hinge is installed so that it is at the top and that the damper swings freely. Reinstall the upper blower motor screw through the adaptor and the blower door and into the back of the microwave oven.
Back of Microwave Oven

Guide Locking Tabs
Adaptor (not shown)

Guide
Blower Motor Door Retaining Screw

14
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 14

2020-04-13 12:02:10

Step-by-step installation guide
3. INSTALLATION
INSTALLATION OVERVIEW
A. Prepare Rear Wall (horizontal duct only) B. Attach Mounting Plate to Wall C. Prepare Top Cabinet D. Mount the Microwave Oven E. Connecting Ductwork (vertical duct only)

A. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for outside exhaust.

B. ATTACH THE MOUNTING PLATE TO THE WALL

CL
· Read the instructions for outside back exhaust on the REAR WALL TEMPLATE.
· Tape the REAR WALL TEMPLATE to the rear wall.
· Cut the opening, following the instructions on the REAR WALL TEMPLATE.
CAUTION: Do not cut an opening in the rear wall if you are installing the microwave with vertical duct or non-vented ductless ventilation.

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through the holes designated to go into drywall, and then reattach the toggle wings so that ¾ of the bolt protrudes beyond the wing.

15
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 15

2020-04-13 12:02:11

Step-by-step installation guide

To use toggle bolts:

MoMuonutnintingg PlaPtlaete

SSppaacciinnggfoforrTTooggglgelseMs oMreore TThhaann WWaallll TThhicickknneessss
TTooggggllee WWininggss TToogggglele BBooltlt

D. MOUNT THE MICROWAVE OVEN

WWaalll

BBoolltt End

3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
NOTE: Before tightening the toggle bolts and wood screw, make sure the bottom of the Mounting plate runs along the bottom Horizontal line of the “Rear wall Template” and the Mounting plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching your fingers between the back of the mounting plate and the wall.
4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. Tighten the screw.

C. USE THE TOP CABINET TEMPLATE TO PREPARE THE TOP CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use the handle during installation.
NOTE: If your cabinet is metal, use the nylon grommet in the power cord hole to prevent the cord from being cut.
NOTE: Filler blocks are required when mounting this unit under any cabinet with a recessed bottom or front overhang. (See page 9.)
IMPORTANT: The case damage that will occur from over tightening screws if you do not use filler blocks is not covered under warranty.
NOTE: When mounting the microwave oven, thread the power cord through hole in the bottom of the top cabinet. Keep it tight throughout Steps 1­3. Do not pinch the cord or lift the oven by pulling cord.
1. Lift the microwave, tilt it forward, and hook the slots at the back bottom edge onto the four lower tabs of the mounting plate.

· Read the instructions on the TOP CABINET TEMPLATE.
· Tape it underneath the top cabinet.
· Drill the holes, following the instructions on the TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

2. Rotate the front of the oven up against the cabinet bottom.

16
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 16

2020-04-13 12:02:11

Step-by-step installation guide

3. Insert a self-aligning screw through the top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep the power cord tight. Be careful not to pinch the cord, especially when mounting flush to the bottom of cabinet.
CCaabbinineettFFrornotnt
CabbiinneettBBootttotmomShSehlfelf FFiilllleerrBBlloocckk

EEqquuiivvaalelennttto DtoepDtehpotfh of CCaabbiinneettRReeccesesss

MiMcricorwowaavveeOOvveennTToopp

SSeellff–AAlilgignnininggScSrcerwew

4. Attach the microwave oven to the top cabinet.
5. Insert the 2 self-aligning screws through the cabinet bottom shelf and filler block into the outer top cabinet of the unit. Continue to support the unit until both screws are inserted and engaged at least two full turns, then fully tighten both screws until the unit is secure.

E. CONNECTING DUCTWORK FOR OUTSIDE TOP EXHAUST
HHoouusseeDDuucct t
1. Extend the house duct down to connect to the exhaust adaptor.
2. Seal the exhaust duct joints using duct tape.

6. Install the grease filters. See the Owner’s Manual packed with the microwave for instructions.

17
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 17

2020-04-13 12:02:11

Before You Use Your Microwave

4. BEFORE YOU USE YOUR MICROWAVE

1. Make sure the microwave oven has been installed according to instructions.

6. Read the Owner’s Manual.

2. Remove all packing material from the microwave oven.
3. Install the turntable and ring in cavity.
4. Replace the house fuse or turn the breaker back on.

7. Keep installation instructions for the local inspector’s use.

5. Plug the power cord into a dedicated 15 amp electrical outlet.
InInssuurereprporpoeprer ggrroouunnddexeixstissts bbeefoforereusues.e
18
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 18

2020-04-13 12:02:11

Note

19
Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 19

2020-04-13 12:02:11

Manual-Installation_MC17J8100CS_AA_DE68-__EN.indd 20

DE68-0000-00
2020-04-13 12:02:11

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>