PROFLO PFWSC2867CP Two Handle Lavatory Faucet Instruction Manual
- June 13, 2024
- PROFLO
Table of Contents
PROFLO PFWSC2867CP Two Handle Lavatory Faucet
CAUTION-TIPS FOR REMOVAL OF OLD FAUCET:
Always turn off the water supply before removing the existing faucet or
replacing any part of the faucet. Open the faucet handle to relieve water
pressure and ensure that water is completely shut off.
CARE INSTRUCTIONS
To preserve the finish of your faucet, apply non-abrasive wax. Any cleaners should be rinsed off immediately. Do not use abrasive cleaners on the faucet.
TOOLS
You may need
INSTALLATION INSTRUCTION
- Shut off water supplies. Place spout through mounting hole in sink, secure spout with metal washer and nut.
- Slide hot and cold end valves through sink mounting holes. Make sure long tubes are installed away from spout. Note: Hot side end valve is labeled. Secure end valves with washers and nuts. Hand tighten nuts onto shank. Lock nuts into position by tightening screws.
- Attach the T-union (2) to the Spout (1) connection,the hot faucet handle (3) connection, and cold faucet handle (4) connection. Push until the connections. snap together. Pull down moderately to ensure the connection has been made.
- Make connections to water lines. Use 1/2″ I. P. S. faucet connections (2) or use supply line coupling nuts (3) with 3/8″ O.D.ball-nose riser (1). Use wrenches to tighten connections. Do not over tighten.
- Remove stopper (1) and flange (2). Screw brass nut (3) all the way down. Push plastic washer (4) and gasket (5) down. Unscrew pivot nut (6) from the pop-up body and remove the seal washers (7). Take off the spring clip (8) from horizontal rod (9). Remove tailpiece (10) from pop-up body.
- Apply silicone to underside of flange (2). Insert body (1) into drain hole from below sink. Screw flange (2) into body (1). With pivot (3) facing toward faucet, pull pop-up straight down into drain hole and secure gasket, plastic washer and brass nut. Apply sealant tape to threads at the top of tailpiece (4) and hand tighten.
- Note: Do not drop silicone onto gasket (5).
- Install horizontal rod (2) and stopper (3) as non-removable (4). Hand tighten pivot nut (1).
- Place one end of spring clip (1) onto the end of horizontal rod (2). Insert horizontal rod (2) through a hole on strap (3). Connect the other end of spring clip (1) to horizontal rod (2). Insert lift rod (4) into strap and tighten screw (5).
- Important: After installation is completed, remove the aerator. Turn on the water supply and allow both hot and cold water to run for at least one minute each. While the water is running, check for leaks. Replace aerator. This flushes away any debris that could cause damage to internal parts.
Maintenance
If the faucet leaks from the spout outlet -Shut off the water supply cartridge (1). Note: Install cartridge (1) correctly for proper handle rotation.
WARNING!
This product is engineered to meet the EPA WaterSense flow requirement. The
flow rate is governed by the aerator or flow controller. If replacement is
ever required, be sure to replace it with a WaterSense compliant aerator or
flow controller to retain the water-conserving flow rate of this product.
Specify Finish
- FERGUSON.COM/PROFLO
- Distributed Exclusively by Ferguson and Wolseley Canada © 2022 Ferguson Enterprises, Inc. 0423 252402
Documents / Resources
|
PROFLO PFWSC2867CP Two Handle Lavatory
Faucet
[pdf] Instruction Manual
PFWSC2867CP, PFWSC2867ZBN, PFWSC2867ORB, PFWSC2867CP Two Handle Lavatory
Faucet, Two Handle Lavatory Faucet, Lavatory Faucet, Faucet
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>