MANROSE FAN7000 Hyper150 EC Axial Fan Instruction Manual
- June 13, 2024
- MANROSE
Table of Contents
MANROSE FAN7000 Hyper150 EC Axial Fan
Product Information
The Designer Series Hyper150 EC Bathroom Fan is a high-quality fan designed for speed control. It features a variable speed EC motor, which leads the way in terms of energy efficiency. The fan is specifically designed to meet New Zealand’s Healthy Homes Standard for bathrooms.
Technical Specifications
- Model: Hyper150 EC
- Type: Axial Fan
- Size: 150mm
- Supply Maximum Pressure: Not specified
- Max. Free-Air Performance: Not specified
- Specific Fan Power: Not specified
- Fan Construction: Axial Fan with Variable Speed Controller
- Impeller & Outer Housing: Not specified
- Maximum Operating Temp: Not specified
- Sound Level: Not specified
- IP Rating: Not specified
Product Usage Instructions
- Step 1: Ensure that the Hyper150 EC Bathroom Fan is installed according to the installation details provided in the Instruction Manual. Proper installation is crucial for compliance with the building code.
- Step 2: Determine the appropriate fan selection based on the size of your bathroom and the number of bends in the ducting system. Refer to the quick reference guide chart provided in the user manual to make the right choice.
- Step 3: Use the FAN2444 fan timer model for all Manrose Hyper150 EC axial inline fans and fan kits. This timer has adjustable delay start and run-on time settings. Do not use the old model FAN2444 or FAN0372 fan timers with EC fans.
- Step 4: For any further inquiries or assistance, contact Simx at the provided contact details.
Note: Always follow the instructions provided in the user manual for safe and proper usage of the Designer Series Hyper150 EC Bathroom Fan.
- Latest EC fan technology
- Continuously-variable speed controllable
- Environmentally friendly with 33% less energy used at just 18W
- Long life with lower operating temperature brushless technology
- Euro flush-box for variable speed control switch – included
Technical Specifications
Technical Specifications – at Full Speed
- Supply 110-240V AC 18W 50Hz
- Maximum Pressure 91 Pa
- Max. Free-Air Performance 105 l/s, 380m3 /hr
- Specific Fan Power 0.17 W/l/s
- Fan Construction Die cast aluminium
- Impeller & Outer Housing PBT plastic
- Maximum Operating Temp 45ºC
- Sound Level 38 db(A)
- IP Rating IP44
- OFF/ON switching for fitting to European flush box DCT4411 included
- 10m long control cable
- 3-pin plug with lead
Dimensions (mm)
Performance Curve – Full Speed
Fan Selection for Bathroom Applications
Hyper150 EC axial inline fan with variable speed controller is designed to
meet New Zealand Building Code G4/AS1 and suitable for bathrooms with less
complex duct runs at full speed. The following chart provides a quick
reference guide for Hyper150 EC axial inline fan with variable speed
controller as being the right choice based on good ducting system selection
and installation best practices being employed. Installation details in the
Instruction Manual must be followed. Compliance with the building code remains
the responsibility of the installer as it is dependant on how the duct and
accessories are installed.
Fan Timer Selection
The FAN2444 fan timer model shown must be used for all Manrose Hyper150 EC
axial inline fans and fan kits. Timer has fully adjustable 0 sec to 5 min
delay start and fully adjustable run-on time after switching off of 0 sec to
20 min. This fan timer model can also be used with AC fans. Old model FAN2444
(with resistor) and FAN0372 fan timers are only suitable for use with AC fans
and must not be used with EC fans.
- PO Box 14347, Panmure, Auckland 1741, New Zealand
- p +9 259 1660 Ie
- sales@simx.co.nz
- wwww.manrose.co.nz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>