EnjoyCool QE01A Portable Power Station User Manual

EnjoyCool QE01A Portable Power Station

Product Information

The Portable Power Station is available in four models:

• Model: QE01A(CN)
• Model: QE01B(CN)
• Model: QE02A(CN)
• Model: QE02B(CN)

The specifications for each model are as follows:

• QE01A(CN): 500Wh, 14.8V, 33.8Ah, Weight: 4.8Kg
• QE01B(CN): 448Wh, 16V, 28Ah, Weight: 5.6Kg
• QE02A(CN): 1065.6Wh, 22.2V, 48Ah, Weight: 9.1Kg
• QE02B(CN): 1008Wh, 22.4V, 45Ah, Weight: 10.2Kg

The power station features multiple ports for charging and powering devices:

• AC Ports: Two AC ports available
• DC Ports: Two DC ports available
• USB-A Ports: Three USB-A ports available
• USB-C Ports: Two USB-C ports available (5525)

The power station also has LED indicators for battery status and a built-in LED light.

Product Usage Instructions

Charging the Power Station:

1. Connect the power station to an AC power source using the provided adapter.
2. Ensure that the power station is turned off.
3. Wait for the power station to fully charge. It takes approximately 6 hours to charge from 3% to 90% and about 9 hours for a full charge.

Using the Power Station

The power station can be used to charge and power various devices. Follow these steps:

1. Identify the type of device you want to charge or power (AC, DC, USB).
2. Connect the corresponding cable or adapter to the appropriate port on the power station.
3. Connect the other end of the cable or adapter to your device.
4. Turn on the power station.

Charging Multiple Devices Simultaneously

You can charge multiple devices at the same time by connecting them to different ports on the power station.

Using the LED Light

1. To turn on the LED light, press the LED button on the power station.
2. Press the button again to switch between different lighting modes.
3. Press and hold the button to activate the SOS mode.

Safety Guidelines

Please refer to the user manual for safety guidelines and precautions when using the power station.

FCC Warning

If using a solar panel for charging, follow these steps:

1. Place the solar charging panel in direct sunlight. Do not expose the product to direct sunlight or moisture.
2. Connect the output round plug (5.5mm) of the solar panel to the DC charging port on the power station.
3. The charging process will start automatically.
4. After charging, remove the round plug of the solar panel from the DC charging port.

Safety Guidelines

• A photovoltaic panel as an input for charging the internal battery shall be provided with an inverter and/or a charge controller in accordance with UL 1741 or UL 62109-1;
• The external power supply shall be a power source in accordance with the Standard UL 60950-1 and CAN/CSA C22.2 No. 60950-1, or UL 1310 and No. 1, CAN/CSA C22.2 No. 223, or No.1, CAN/CSA C22.2 No. 223;
• A vehicle adapter that complies with the enclosure and input contacts requirements in the Standard for Vehicle Battery Adapters, UL 2089, and Power Supplies, CAN/CSA C22.2 No. 107.1. The connector plug shall incorporate a fuse or other protective device having a current rating not greater than 15 A.
• INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using this product, basic precautions should always be followed, including the following:

• a ) Read all the instructions before using the product.
• b ) To reduce the risk of injury, close supervision is necessary when the product is used near children.
• c ) Do not put fingers or hands into the product.
• d ) Use of an attachment not recommended or sold by power pack manufacturer may result in a risk of fire, electric shock, or injury to persons.
• e ) To reduce risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the power pack.
• f ) Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• g ) Do not operate the power pack with a damaged cord or plug, or a damaged output cable.
• h ) Do not disassemble the power pack, take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or electric shock.
• I) To reduce the risk of electric shock, unplug the power pack form the outlet before attempting any instructed servicing.
• j) WARNING – RISK OF EXPLOSIVE GASES.
• To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of any equipment you intend to use in vicinity of the battery. Review cautionary marking on these products and on engine.

PERSONAL PRECAUTIONS

1. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
2. Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery.
3. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with running cold water for at least 10 minutes and get medical attention immediately.
4. NEVER smoke or allow a spark or flame in vicinity of battery or engine.
5. Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-circuit battery or other electrical part that may cause explosion.

• l ) When charging the internal battery, work in a well ventilated area and do not restrict ventilation in any way.
• m ) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• n ) Do not expose a power pack to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion. The temperature of 130°C can be replaced by the temperature of 265°F.
• o ) Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

SAVE THESE INSTRUCTIONS

General Questions And Answers

Q: How long can the product be stored?

• A: It can be stored for 6 months when fully charged. It is recommended to charge it every three months.

Q: How long does it take for the product to be fully charged?

• A: Charge from 3% to 90% with the original adapter for about 6 hours, and it can be fully charged in about 9 hours.

Q: Can you charge the product with DC charging port and usb-c port at the same time?

• A : It can be charged at the same time, and the charging time will be shortened.

Q: Can the product be used while charging?

• A: It can be used while charging. When the output power is greater than the charging power, the battery power will be reduced.
• When it is reduced to a low power state, the output will be turned off.

Q: Does the product have temperature protection?

• A : When the internal temperature is higher than 55 ℃ during charging, it will be protected; when the internal temperature is higher than 60 ℃ during discharging, it will be protected.

Q: Will the product shut down automatically?

• A : It will not shut down automatically until it is fully discharged. Under normal circumstances, it will not shut down automatically after power on.

Q: Can the product be used to start the car?

• A: It cannot be directly used to start the car. However, another charging line can be selected to charge the starting battery of the car.
• When the power of the product is ≥ 20%, the car can be started after charging for 5-10 minutes.

Q: After being fully charged, the power percentage and Fu are not displayed synchronously or have errors. Is it normal?

• A: Normal image: “ Fu” will be displayed when fully charged, but the power percentage may be 99%.

FCC Warning

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
FCC ID: 2A49V-QE01A

Solar Panel Charging (optional)

1. Place the solar charging panel in direct sunlight. (Note: Do not expose the product to direct sunlight or moisture)
2. Connect the output round plug (5.5mm) of the solar panel to the DC charging port, and the charging starts.
3. After charging,please remove the round plug of the solar panel from the DC charging port.

Car Charging (optional)

1. Connect the round plug (5.5mm) of the car charger cable to the DC charging port of this product, and then insert the car charger plug into the vehicle’s 12V car charger port to start charging.
2. After charging, please remove the car charger first, and then pull the round charging plug out of the DC charging port.

Note: Do not insert the car charger plug into the car charger port of this product to charge itself.

Troubleshooting

1. There is no response when the product is turned on, and DC, USB, AC and LED lights have no output. Terms of settlement:
   • Remove all electrical equipment, then charge it for 5-10 minutes and restart.
   • Please ensure that the product is currently used within the normal temperature range.
2. The product can be powered on, but the corresponding output interface has no output (DC, USB, AC). Terms of settlement:
   • Check whether the product power of is too low. If so, please charge it in time.
   • Check whether the electric equipment is higher than the product output power and resulting in protection, remove the load and restart.
   • Confirm whether the product output meets the power requirements of electrical equipment.
   • Check whether there is a short circuit between the output port and the electric equipment. Remove the equipment and restart it
   • Check whether the equipment can be used normally by using other power sources, which may be caused by incompatibility of individual equipment.
3. Unexpected shutdown during use. Terms of settlement:
   • The startup of the internal protection system leads to the shutdown of the product, and the events that may lead to the startup of the protection system include overcharge, over discharge, high temperature, low temperature, overcurrent and short circuit. In order to quickly solve the problem, please remove all electrical equipment, keep the product temperature static within the normal temperature range, and charge the product for 5-10 minutes. At the same time, check whether the electrical equipment is faulty, then restart.
4. The product cannot be charged. Terms of settlement:
   • Please confirm whether the charging electrical parameters are within the charging range of this product.
   • Check whether the current equipment has started the temperature protection because the temperature is too high or too low.

Maintenance And Service

• It is recommended to use or store the product at 20 ℃ to 30 ℃, away from water source, heat source and other metal objects.
• For safety reasons, do not store the product in an environment higher than 45 ℃ or lower than – 20 ℃.
• If you need long-term storage, please charge and discharge the product every 3 months (that is, discharge the product to 30% and then charge it to 60%).
• If the power of this product is less than 1% after use, please charge it to 60% before storage. If it is left idle for a long time under the condition of serious power shortage, it will cause irreversible damage to the cell and shorten the service life of the product.

Wireless Charging

1. Press and hold the USB switch to turn on the wireless charging function, the display screen will show wireless charging output symbol.
2. Put the device to be charged on the top center position for wireless charging. The charging position may need to be adjusted appropriately for different charging devices.
3. After use, long press the USB switch to turn off the wireless charging function.

LED Lighting

1. Short press the LED switch to turn on the LED lighting function.
2. Short press the LED switch to change the LED modes in sequence: Weak, Medium, Strong, SOS, flash, Off.

Power Off With One Button
Press and hold the LED switch to turn off with one button (close all enabled functions), and the display will be turned off.

Adapter Charging

1. Insert the round charging plug of provided adapter into the DC charging port, and then insert the power plug of the adapter into the mains socket to charge.
2. After charging, please pull the adapter power plug out of the mains socket, and then remove the round charging plug from the DC charging port.

Note: Please do not plug the adapter power cord into the product’s AC outlet to charge itself.

USB-C Charging

1. Connect the USB-C charging cable to the USB-C port of the product, and then plug the other end of the USB-C charging cable into the USB charging socket to start charging.
2. After charging, please unplug the USB-C charging cable from the USB- C port.
3. USB-C charging can be performed simultaneously with power adapter charging/solar panel charging /car charging.

Note: Please do not use the product’s output to plug into the product’s USB-C to charge itself.

Charge and Discharge

• It is recommended to charge it immediately after purchase. Charge the battery immediately when the remaining power is below 20% to maintain optimum performance and extend service life.
• When charging, the product will be initialized first, and all symbols on the display will light up. After the self-check, it will enter the charging mode, and the display will show “CH” for a long time(charging), “FU” means fully charged.
• Do not charge the product with its output.
• When discharging, the current remaining time of discharge will be displayed, and the remaining time will be automatically adjusted according to the load. After the battery is discharged, the screen will automatically turn off.
• Do not fully discharge the internal battery as it may affect battery life.
• When the warning symbol of high and low temperature protection appears on the display, please stop using it and shut it down immediately.

AC Output

• Press and hold the AC power switch to turn on or off the AC power socket

1. Connect the AC powered device to the AC socket (make sure the powered device is turned off before inserting the plug into the AC socket).
2. Press and hold the AC power switch to turn on the AC power outlet, and the display will show AC output.
3. After use, long press the AC power switch, turn off the AC power socket, and unplug the device from the AC power socket.

When AC output of the product is not used, please turn off the AC power switch to save energy.
Notice:

• The AC voltage standards and socket specifications are different in different countries or regions. Please make sure that this product conforms to the specifications of the electrical equipment before use.
• Do not connect other AC power sources to the product’s AC outlet.
• Do not put the plug of adapter into the product’s AC outlet to charge itself.
• When the AC output is short-circuited or the power of the load appliance exceeds the AC output power, the protection function of the product will be activated.
• Please remove the short-circuit or remove the electrical equipment, and then restart the machine to restore the AC output function.

DC Output

Press the DC switch to turn on or off the DC output DC output port:

1. Insert the DC plug of the electrical device into the DC output port of this product, then press the DC switch to turn on the DC output, and the display screen will show DC output.
2. After use, press the DC switch to turn off the DC output, and pull the plug of electrical device out of the DC output port.

Car charging port:

1. Insert the car charger plug into the car charger port, press the DC switch to turn on the DC output, and the display screen will show DC output.
2. After use, press the DC switch to turn off the DC output, and pull the plug of electrical device out of the car charger port.

USB Output

Press the USB switch to turn on or off the USB output

1. Insert the USB cable plug into the USB-A port or USB-C port of the product, then press the USB switch to turn on the USB output, and the display screen will show USB output.
2. After use, press the USB switch to turn off the USB output, and pull the USB cable plug out of the USB-A or USB-C output port.

Specification

Product Diagram

The AC power socket, AC output voltage and frequency of this product will be changed due to different countries or regions, please refer to the actual product!

1. Display screen
2. DC charging port
3. AC power switch
4. AC power socket*2
5. DC switch
6. Car charger port
7. DC output port*2
8. USB switch
9. USB-C
10. USB-A 1
11. USB-A 2 & USB-A 3
12.  LED switch (one button to power off)
13. LED lighting
14. Wireless charging

Display Screen

1. Battery level/Charge status
2. Remaining power
3. Discharge remaining time/Charge/Discharge status
4. High and low temperature protection warning
5. AC output
6. DC output
7. USB output
8. Wireless charging output
9. AC output frequency (60Hz)

Note:

• a. Please turn off the display screen in time if the product is not in use;
• b. Press and hold the LED switch to turn off with one button.

Disclaimer

• Before using the product, please read the instruction manual of this product and make sure to use it correctly after fully understanding it. After reading, please keep the manual properly for future reference. If you do not operate this product correctly, you could cause serious injury to yourself or others, or result in damage to the product and property. Once you start to use this product, you are deemed to have understood, recognized and accepted all the terms and contents of this manual. Users undertake to be responsible for their own actions and all consequences arising therefrom. The manufacturer is not responsible for all losses caused by the user’s failure to use the product in accordance with the User Manual.
• In compliance with relevant laws and regulations, the manufacturer has the final right to interpret this manual and all related documents of this product.
• Subject to update, revision or discontinuation without notice.

Product Overview

• Thank you very much for using our portable power station product. In the design of this product, a multi-level safety mechanism is adopted, and the product safety and reliability are fully guaranteed. It has multi-port AC output and DC output functions, which can meet the power supply needs of mobile phones, notebook computers, cameras, TV sets, various chargers, game consoles, DVD players, small electrical tools and other equipments, and built-in LED lighting.

Packing List

Specification

Documents / Resources

| EnjoyCool QE01A Portable Power Station [pdf] User Manual
QE01A, QE01B, QE02A, QE02B, QE01A Portable Power Station, Portable Power Station, Power Station, Station
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>