MANROSE FAN7421 Vento Hand Dryer Instruction Manual
- June 13, 2024
- MANROSE
Table of Contents
FAN7421 Vento Hand Dryer
Instruction Manual
INSTALLATION INSTRUCTIONS
Vento Hand Dryer
FAN7421 – White
FAN7422 – Black
TECHNICAL SPECIFICATIONS
Supply: 220 – 240V AC
Total Power: 1350 W
Air Speed: Adjustable 100 m/s max
Dry Time. 9-11 sec
Housing: Stainless Steel 304
Auto Shut Off: 60 sec
Sound Level: Adjustable 70 db(A) max
Safety: Class I
IP Rating: IP23
IK Rating: IK08
Dimensions (A x B x C): 256 x 173 x 152 mm
Net Weight: 3.5 kg
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
IMPORTANT
This product is suitable for use only with a supply voltage of 230-240V AC,
5014z.
All electrical work must be carried out in accordance with bcal and national
electrical codes as applicable.
We strongly end that this device is installed by a registered electrician.
Always switch power off prior to installation. A means of mains power
isolation must be installed in the circuit for the purpose of safe access for
any internal cleaning, recalibraticn. or maintenance.
This device is not intended for use by Persona (inducting children) with
reduced phySiCal, Sensory or mental capabilities, or lack of experience and
knowledge. unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Young children Should be supervised to ensure that they do not play with the
appliance.
Any changes or modifications made or attempted to this product, without the
prior written approval of the manufacturer, will void any and all stated
warranties.
BEFORE INSTALLATION
See mounting template for complete reference to mounting heights and power
knockout locations.
It is
recommended to avoid installation of dryer near high reflective objects
(mirror, stainless steel washbasins, etc.) in order to avoid errant function
of the presence sensor.
INSTALLATION
-
Be sure to break the electric supply before any operation.
-
Using the mounting template supplied, mark mounting hole locations for correct height above the floor and drill 4x mounting holes.
-
Remove transport screw at the rear of the dryer and unscrew front cover from the base of the unit using the hex key provided.
a. For
in-wall (concealed) power supply: provide supply wire to knockout location
according to local code and attach securely to chassis at knockout with
appropriate strain relief connector (not supplied).
b. For surface mounted conduit (exposed) power supply: provide appropriate conduit to entry location accordingly to local code and attach securely to chassis with correct strain relief connector (not supplied). -
Fix base to the wall.
-
Connect supply and ground wires to terminal block where indicated.
-
Before replacing cover, there is a customized option to run the dryer heater on (1350 W) or heater off (500VV).The switch is clearly marked.
-
Adjustable detection distance. Default setting is 120-150mm from nozzle.
-
Adjustable speed, sound and heat control.
-
Re-attach the cover to the base of the unit using the hex key provided. Reconnect power supply and test operation.
MAINTENANCE
Periodic cleaning of this unit is required to maintain optimum performance and
reduce unnecessary wear on parts.
Depending on usage, a regular maintenance programme with a frequency between
3-6 months is highly recommended.
Detach the cover from the dryer and remove any dust or lint. Remove and
discard the existing filter (the HEPA filter cannot be cleaned and reused).
Replace with a new HEPA filter and reassemble after cleaning.
Wipe the cover with a damp cloth and mild cleaning solution. Do not soak.
Never use abrasives to clean the cover.
WARRANTY
This product is guaranteed by Simx Ltd for 3 years from the date of purchase
against faulty materials or workmanship which affects its design ability to
switch and operate. During this period if the product has a defect of this
nature it will be repaired or replaced free of charge by Simx with the same
item, or a similar one of higher specifications, ON THE CONDITIONS THAT:
The buyer returns it to the seller from whom it was bought, freight paid.
The product has been bought by the user, i.e. a receipt/sales invoice is
produced as a proof of purchase.
The product has not been misused or handled carelessly, installed in anyway
contrary to the installation instruction, or installed in any unusually
exposed or harsh environmental conditions.
This guarantee excludes liability for any discolouration or delamination of
paint or plastic, or any user replacement parts. It does not confer any rights
other than those expressly set out above and does not cover any claims for
consequential loss or damage.
Our Goods come with guarantees that cannot be excluded under the Australian
and New Zealand Consumer Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the Goods repaired or replaced if the
Goods fail to be of acceptable quality and the failure does not amount to a
major failure.
Specifications are subject to change without notice.
Distributed by Simx (NZ) and Ventair (AUS)
PO Box 14 347, Panmure, Auckland, NZ.
Technical Support (09) 259 1662
e: sales@simx.co.nz
www.simx.co.nz
www.ventair.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>