TANDELTA OQDe Display Express User Guide
- June 12, 2024
- TANDELTA
Table of Contents
TANDELTA OQDe Display Express
Product Information
The product is called “Display Express” (OQDe). It is an accessory that is used in conjunction with the OQSx-G2 Sensor. The Display Express allows users to configure and monitor the OQSx-G2 Sensor. It comes with a Quick Start Guide to help users get started.
Installation Requirements
The OQSx-G2 Sensor and cables are sold separately. Users need to have the OQSx-G2 Sensor and necessary cables for installation and connection.
WHAT’S IN THE BOX?
Display Express (OQDe)
CONFIGURE
WARNING: You MUST configure the OQSx-G2 Sensor using CADS before configuring the OQDe.
-
Search for active WiFi networks on PC or Mobile device. Connect to “Tan Delta OQDe” WiFi Hotspot. Password = password
-
Navigate to Insight by manually going to web address http://192.168.4.1 or scan the QR Code below:
QR SCAN -
Configure OQDe parameters using Insight, including preferred units and warning and alarm levels. NOTE: Default oil condition warning and alarm levels are set for a diesel engine application.
INSTALL AND CONNECT
Cable DB Pin Out
ACTIVATION STEPS
- Check installation
- Power on
- Wait for 1 minute
- Check output
TROUBLESHOOTING
- Check configuration.
- Refer to Master User Guide available at: www.tandeltasystems.com/support
- Contact: support@tandeltasystems.com
INTERPRETING OIL CONDITION
What does it mean?
High readings usually indicate the sensor head is in air. Check the location and move if necessary, so head is submerged in oil. If location is OK, the high reading could be caused by fuel contamination or sweetening.
Oil condition is okay for the application selected and can continue to be used in operation. However, continued monitoring of the oil will detect any deviations from the expected oil life curve. If detected, investigate for potential issues which could lead to failures of equipment before they happen.
- Oil is nearing the end of its life. Schedule maintenance.
- Oil is no longer operationally viable. Change immediately.
If your application is not listed, please contact Tan Delta Support to discuss a solution.
SUPPORT – FAQ
If you have any issues, please read the tips below before contacting us for further support.
-
Does the sensor require cleaning?
No, cleaning is required once the sensor is installed. However, when using the sensor for testing offline samples (i.e. MOT Kit), then cleaning between samples is essential. -
Where can I find the list of Event Codes for the Display Express?
The Master User Guide linked at the botom of this page contains the list of Event Codes, which can be displayed on the device. -
I cannot see my oil in the database, so I have used an oil which I believe is close, but the sensor isn’t working?
The sensor will exhibit a different response for every oil. For best results, it is advised to obtain an Oil Profile which Tan Delta will add to our Oil Database. Please complete and submit an Oil Profile Request Form online at www.tandeltasystems.com/oil-availability-checker/ -
How do I update the software?
Software updates will happen automatitically. You will be prompted to accept when one is available. If you are provided an installer by Tan Delta, please uninstall any previous versions of software before installing the new one. -
How do I remove the software?
Simply go into your control panel and remove the software.
QR SCAN
Alternatively, refer to Master User Guide available at:
www.tandeltasystems.com/support
You can find further information in the Master User Guide on the support page
of our website. If you have any further questions, please contact our support
team by email:
support@tandeltasystems.com who will
answer no later than the next working day.
www.tandeltasystems.com
support@tandeltasystems.com
Copyright © Tan Delta Systems Ltd.
References
- Tan Delta Systems - Tan Delta Systems PLC
- Oil Database - Tan Delta Systems PLC
- Support | Tan Delta Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>