Bradas ECO-3137 Watering Timer Instructions

Bradas ECO-3137 Watering Timer

1. Filter
2. Tap adapter 3/4″
3. LCD Screen
4. Button +
5. Button –
6. Connector adapter
7. Button settings/OK
8. Return button
9. Manual control mode

BATTERY INSTALLATION

Open the battery compartment on the back of the controller, insert 2 alkaline batteries AA and close the compartment.

Note:

1. When the LCD screen shows a flashing battery icon, it means a low battery level and they must be replaced.
2. When the battery voltage is lower than 2,4V, close the solenoid valve.

CONTROLLER INSTALLATION

LCD SCREEN ICONS

RESET
Press buttons 7 i 8) and hold for 5 seconds to reset the controller to its factory default settings.

CURRENT TIME SETTINGS
Press button 7, then button 5) or 4) (hold to change numbers quicker) to set the current time. Press the button 7 to confirm settings.

MANUAL CONTROL SETTINGS

• Press button 9, then button 5 or 4) (hold to change numbers quicker) to set irrigation time from 1 minute – 23 hours 59 minutes.
• Press the button 7 to confirm settings (if not confirmed within 1 minute, the screen returns to its initial display).
• Press button 9 again to turn the manual control off.

Note: When manual control time finishes, the controller resumes automatic mode.

IRRIGATION PROGRAM SETTINGS

Press button 7 until icon P1 starts flashing.
Use button 5 or 4 to choose an exact program and set it in succession:

1. Program turning on/off
2. Use buttons (5) or 4) to turn the exact program on or off. Press button 7 to confirm settings.
3. Irrigation start time settings
4. Use buttons (5) or 4) to set the irrigation start time.
5. Press the button (7 to confirm settings.
6. Irrigation duration time settings
7. Use button (5) or (4) to set irrigation duration time from 1 minute – 23 hours 59 minutes.
8. Press the button 7 to confirm settings.
9. Irrigation frequency settings
10. Use buttons 5) or 4) to set irrigation frequnecy every 1 hour – 30 days.
11. Press the button 7 to confirm settings. Follow the same steps to set up more programs P2 and P3.

Note:

1. Possible to set 3 programs.
2. Programs can be modified and settings easily at any time.
3. When only 1 program is set, the display shows only P1.
4. The setting of two same irrigation times is impossible, for example: when the start time for P1 is set for 12:00-13:00, the same time cannot be set, but 13:01.

DISPLAY LOCK

• Press buttons 5 and 4 at the same time and hold for 5 seconds to lock the display.
• Repeat this action to unlock the display.

TURN ON/OFF CONTROLLER

• Press button 8 and hold for 5 seconds to turn the controller off.
• Repeat this action to turn the controller on, display returns to its initial display.

CARE AND MAINTENANCE

1. Only for outdoor use to control sprinklers and irrigation systems. Do not use for industrial purpose in contact with food products, chemicals and pesticides.
2. Operating water pressure: 0,5 – 6 bar (7 – 87 psi).
3. Operating water temperature: 0°C – 60°C.
4. Protect the controller during the winter season and freezing conditions.
5. Protection level: IP44.
6. Install the controller above ground and vertically to tap.
7. Do not submerge in water and avoid the controller to be in contact with water.
8. Do not pull the hose once attached to the controller to avoid any damage.
9. The filter traps dirt particles and prolongs the life of the controller. Clean the filter regularly and replace it when worn.
10. Do not use spanners or pliers to avoid damage to the controller.
11. If the controller does not work, read the instructions carefully again or contact your store service before returning the timer to the store.

MAINTENANCE

1. Close tap and remove the controller.
2. Drain out water from the controller.
3. Remove batteries.
4. Dry controller and store in a dry indoor place.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>