LAURA ASHLEY O7J3IEHD23723AQ 3 Light Wall Lamp Instruction Manual

LAURA ASHLEY O7J3IEHD23723AQ 3 Light Wall Lamp Instruction Manual

Item Number: O7J3IEHD23723AQ

WARNING (To reduce the risk of fire, electric shock, orpersonal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is

» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “ OFF ” position.
» Place the wall switch in the “ OFF ” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before
6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDED:

• Mounting plate (1)
• Green ground screw (1)
• Back plate (1)
• Screw (2)
• Socket (3)
• Lampshade (3)
• Socket ring (3)

ACCESSORIES ENCLOSED:

(A) Mounting screw (2)
(B) Plastic wire connector (3

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above

2.  Turn off power

Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “ OFF ” position.
» Place the wall switch in the “ OFF ” position.

3.  Make assembly

Step A1 » Unscrew screws (F) from back plate (E) and mounting plate (C), then set them aside for later installation.
Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (C).
Secure mounting plate (C) to the outlet box with mounting screws (A).
Step A3 » Make wire connections
Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

__

Twist wires together with plastic wire connectors (B) until tightlyjoined, and wrap each
connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate
(E) to mounting plate (C) with the previously removed screws (F). Hand tighten until snug.

NOTE: back plate (E) should be snug against the wall with screws (F).

If not, remove back plate (E), adjust the threaded length ofpre-assembled mounting screws on mounting plate (C):

• Unscrew the pre-assembled hex
• Screw the pre-assembled mounting screws in or out ofmounting plate (C).
• When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step

Step A5 » 1) Remove socket rings (I) from sockets (G).

• Carefully hang lampshades (H) onto sockets (G), and then screw socket rings (I) to sockets (G) to secure
  • When installing socket rings (I), the orientation ofsocket rings (I) is that the side ofrolled edge faces
• Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the

socket.)

1. Check that everything is installed properly, then you can turn on the

light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>