SHARP MX-M3071S External Vendor Interface Cable Kit Instruction Manual
- June 12, 2024
- Sharp
Table of Contents
SHARP MX-M3071S External Vendor Interface Cable Kit
Product Information
The DVENDFSV External Vendor Interface Cable Kit is designed for use with the following models: MX-M3071S, MX-M3571S, MX-M4071S, MX-M5071S, and MX-M6071S.
This kit is intended for installation by a Sharp authorized technician.
Kit Contents:
- Screw
Product Usage Instructions
Step 3:
Ensure the screw is securely fastened.
Step 5:
Follow the subsequent steps.
Step 6:
Pay attention to the position of the round terminal mount.
Step 8:
Continue with the installation process.
Step 9:
Proceed with the installation process.
Step 10:
Enter the pass code when prompted.
Normal Mode:
Use the button to switch to Normal Mode.
Easy Mode:
Use the button to switch to Easy Mode.
Vendor Mode:
To enable Vendor Mode, follow the instructions below:
- Access the screen.
- Select MODE 1, MODE 2, or MODE 3 based on the preferred setting shown in the Condition Table.
Select MODE 1, MODE 2, or MODE 3 based on the preferred setting shown in the Condition Table. The default setting is MODE 3.
Condition Table
| Mode 1 | Mode 2 | Mode 3 |
|---|
The specified number of copies are completed and there is money
remaining| Insufficient money remaining in case of B&W/Color job| The machine
will auto clear after 60 seconds (default
setting)
The machine will auto clear after 60 seconds (default
setting)| The machine will auto clear after 60 seconds (default
setting)| The current setting is cleared immediately and display resets
to initial screen
Insufficient money remaining in case of B&W job, but Color
has money remaining| The machine will not auto clear| The machine will not
auto clear
The specified number of copies are completed and there is no
money remaining| The machine will auto clear after 60 seconds (default
setting)| The machine will not auto clear
The machine will not auto clear| The machine will not auto clear| The machine
will auto clear after 60 seconds (default
setting)
The current setting is cleared immediately and display resets
to initial screen| |
Printer Control Description
Use Case Examples:
Mode 1:
All the items in OUTSIDE AUDITOR and VENDOR MODE are allowed. Options can be selected.
Mode 2:
OUTSIDE AUDITOR is always set to P VENDOR 1. Other buttons are grayed out. VENDOR MODE is always set to MODE 3. Other buttons are grayed out.
Mode 3:
OUTSIDE AUDITOR is always set to P OTHER. Other buttons are grayed out. VENDOR MODE is always set to MODE 3. Other buttons are grayed out.
Mode 4:
Used to set the system to work with a coin-operated controller. Only the copy mode will be controlled. Also, the VENDOR MODE is set to MODE 3.
Mode 5:
Use this setting when connecting the system to an external auditor that will control scanning only on the machine. Also, the VENDOR MODE is set to MODE 3.
Installation Instructions
for DVENDFSV External Vendor Interface Cable Kit Models: MX-M3071S / MX- M3571S / MX-M4071S / MX-M5071S / MX-M6071S
(For installation by a Sharp authorized technician)
Kit Contents:
- (1) Vendor Interface Cable
- (1) 8″ Stress Relief Tie
- (3) 4″ Nylon Mounting Ties
- (1) #8 x ¾″ Self Tapping Scew
- (1) #8 SAE Washer
Step 1:
- Prepare the cable for installation.
- Have other installation accessories at hand.
Step 2:
- Ensure machine is turned off and unplugged from wall outlet
- Disconnect Network and Fax line (if equipped)
Step 3:
- Remove the 1 screwand remove the ROM cover.
- Remove 6 screws and remove the rear cover
Step 4:
- Back coverremoved
Step 5:
- Preparethe cable
- Fasten the cable ties to the cable.
- Pay attention to the fastening direction of the tie to ensure proper mounting direction.
- The extra end of the tie should be cut off with 1-2 mm remained.
Step 6:
- Insertthe connectoronto the PCU PWB.
Step 8:
- Open the cut out on the ROM Cover and pass the wire through the hole. Attach the coverwith 1 screw.
Step 9:
- Re-install the rear cover using 6 screws.
Step 10:
- Re-attach the ROM cover using 1 screw.
Reference:
Enter to Simulation Mode
- Enter password entry screen in the same way with current model.
- Enter password to log into pass code entry screen. (new)
- Enter pass code to log into Simulation Mode .
- Passwordisneeded.(forservice)(new)
- Pass code is needed.
Reference:
New Simulation Mode (new)
- After passcode is entered, Easy Simulation Mode is displayed.
- Simulation Mode is switchable by button.
- Default Simulation Mode is Normal Mode.
Normal Mode
Easy Mode
Step 11:
Enable the Vendor Mode
- Enter simulation 26-3
- Refer to screen shot below -On the line for Outside Auditor, select “P Vendor 1’’
- DefaultScreenforSimulation26-3
- Vendor mode turned on
Step 12:
Optional Settings: Document Filing
- Refer to the screen shot below -On the line for DOC ADJ, select “ON’’ to enable
- Document Filing. The default setting is OFF.
- Screen with previous setting turned on for Simulation 26-3:
- Doc ADJ turned on
Step 13:
Optional Settings: Continuous Paper Feeding
Refer to the screen shot below – On the line for PF ADJ, select “ON’’ to
enable Continuous Paper Feeding. The default setting is OFF.
Screen with previous settings turned on for Simulation 26-3:
PF ADJ turned on
Step 14:
Optional Settings: Vendor Mode
Refer to the screen shot below – On the line for VENDOR MODE, select MODE 1,
MODE 2, or MODE 3 based on the preferred setting shown in the Condition Table
below. The default setting is MODE 3.
Condition Table
| The specified number of copies are completed and there is money remaining| Insufficient money remaining in case of B&W/Color job| Insufficient money remaining in case of B&W job, but Color has
money remaining
| The specified number of copies are completed and there is no money
remaining
---|---|---|---|---
Mode 1| The machine will auto clear after 60 seconds (default setting)| The
machine will not auto clear| The machine will not auto clear| The machine will
auto clear after 60 seconds (default setting)
Mode 2| The machine will auto clear
after 60 seconds (default setting)
| The machine will auto
clear after 60 seconds (default setting)
| The machine will not auto clear| The machine will auto
clear after 60 seconds (default setting)
Mode 3| The machine will auto clear after 60 seconds (default setting)| The current setting is cleared immediately and display resets to
initial screen
| The machine will not auto clear| The current setting is cleared immediately and display resets to
initial screen
Step 15:
Optional Settings: Count-up Timing
Refer to the screen shot below – On the line for COUNTUP TIMING,
- Select FUSER_IN to change the count-up timing to when the lead edge of the paper passes over the sensor after fusing
- Select FUSER_OUT to change the count-up timing to when the trail edge of the paper passes over the sensor after fusing
Select EXIT_OUT to change the count-up timing to when the trail edge of the
paper passes over the eject sensor (this is the default setting)
Printer Control
|
Description
|
Use Case Example
---|---|---
Mode 1
| All the items in OUTSIDE AUDITOR and VENDOR MODE are allowed| This is the default setting and all options can be selected.
Mode 2
| OUTSIDE AUDITOR is always set to “P VENDOR 1”. Other buttons are grayed out. VENDOR MODE is always set to MODE 3. Other buttons are grayed
out.
| Used to set the system to work with a coin operated controller. Only the copy mode will be controlled. Also the VENDOR MODE is set to MODE3
Mode 3
| OUTSIDE AUDITOR is always set to “P OTHER”. Other buttons are grayed out. VENDOR MODE is always set to MODE 3. Other buttons are grayed out.| Use this setting when connecting the system to an external auditor that will control scanning only on the machine. Also the VENDOR MODE is set to MODE3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>