PogoLab M3 Wireless Transmission System User Manual

M3 Wireless Transmission System
User Manual

M3 Wireless Transmission System

M3 WIRELESS SYSTEM
Thank you for choosing the M3 wireless transmission system.Please read the following instructions carefully before you use it.

SPECIFICATION

1. Power button
2. Indicator LED Light
3. TYPE-C Charging Port

BASIC OPERATION

1. Press and hold the “button” of the transmitter or receiver for 1 second, and the indicator light around the button will light up or off, that is, power on or off. Under normal circumstances, the transmitter and receiver can be used after the indicator lights are always on and not flashing.
2. Then insert the transmitter into the corresponding interface of your musical instrument and the receiver into the corresponding interface of your speaker, and you can use it.

RE-MATCH METHOD

If both the transmitter and receiver are turned on, the lights of the transmitter and receiver are on flashing, then you need to try to re-pair, the operation is as follows:
At this time, please turn off the transmitter and receiver, and then turn on the transmitter and receiver simultaneously .
At the same time, observe whether the indicator light of the transmitter and receiver are always on (not flashing).
If the flashing is always on, it means that the pairing is successful and it can be used normally.

ABOUT CHARGING

1. When the battery is low, the indicator light will flash red (The light will stop flash when the battery totally goes out).Please charge the device with the Type-C cable attached. When charing , the indicator light will flash, and will always on when the battery is fully charged.

2. If the indicator light does not light up when it is turned on normally, maybe the battery has run out , please try to charge it.

3. In the power-on state, lightly press the “button” to check the power status by observing the light.
   If the indicator light flashes Four times, it means 100% battery left.
   If the indicator light flashes Three times, it means 75% battery left.
   If the indicator light flashes Twice, it means 50% battery left.
   If the indicator light flashes Once, it means 25% battery left.
   Our M3 guitar system can be used up to 8 to 10 hours when it is fully charged.

4. During the charging process, the “button” on the device cannot be operated.

5. The parameters of the charger used are 5V 1A–2A.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and  compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure andcompliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

www.lekatodeal.com
support@lekatodeal.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>