mart cart 280-5563 Electric Shopping Cart Owner’s Manual

June 12, 2024
mart cart

mart cart 280-5563 Electric Shopping Cart

mart cart 280-5563 Electric Shopping Cart-PRODUCT

Product Information

  • Product Name: Mart CartTM Model 280-5563
  • Manufacturer: Assembled ProductsTM Corporation
  • Website: www.martcart.com
  • Contact Number: 1-800-548-3373

Product Usage Instructions

  1. Before operating the cart, it is important to read the enclosed information in the owner’s manual and technical documentation.
  2. Check the shipping carton for any visible damage. If there is any damage, report it immediately to the freight carrier and file a claim if necessary. Also, check the contents of the carton and report any discrepancies to the carrier and the factory.
  3. To order parts, contact the Service Department at 1-800-548-3373 or 479-636-5776. Make sure to provide them with the serial number of your cart, which is located on the seat support tube under the seat.
  4. All parts will be shipped with approved credit card, check in advance, or C.O.D. Commercial accounts are allowed 15-day terms from the date on the invoice with approved credit.
  5. The owner of the cart is responsible for maintaining it in a safe and reliable operating condition at all times.
  6. Note that specifications found in the manual are subject to change without notice.

Daily Maintenance Check List
Follow the daily maintenance check list provided in the manual to ensure proper functioning of the cart.

Battery Charging Instructions
Before charging the battery, read the battery charging instructions carefully.

Important Safety Instructions
Read the important safety instructions provided in the manual before operating the cart to ensure safe usage.

Operating Procedures

Turn on/off the cart using the rocker switch located at the service counter.

The LED color status indicates the current operating and charging status of the battery:

  • LED Off: Rocker switch is set to the off position.
  • Green (solid): Rocker switch is set to the on position, seat switch is engaged, and battery is fully charged.
  • Amber (solid): Rocker switch is set to the on position, seat switch is engaged, and battery is below 12.4 volts.
  • Red – Flashing: Battery needs to be charged, voltage is below 10.5 volts.

While charging, ensure that the charger is plugged in and the battery is being charged. The LED color status will indicate when the battery is fully charged.

Note: It is recommended to replace the original AGM (Suspended Electrolyte) Battery with the same type and rating to prevent damage to the cart’s internal components, charging system, or personal injury.

Model 280-5563

Mart Cart™ is a quality product line of Assembled Products™ Corporation
115 E. Linden • Rogers, Arkansas 72756 USA
479-636-5776479-636-3245 fax 1-800-548-3373 www.martcart.com

IMPORTANT INFORMATION

Please read before operating.

CONGRATULATIONS!
You have just purchased the best electric shopping cart on the market today. This Mart Cart incorporates the very latest in technological advances. To assure you of the best and safest performance as well as longest life, please read the enclosed information. After reading this manual, should you have a service problem or need help, please call our Customer Service Department with the serial number of your cart, at our toll free number: 1-800-548-3373 or 479-636-5776.

DAMAGE: Check the shipping carton for any visible damage. Report the damage to the freight carrier immediately. File a claim with the carrier if actual damage to your cart has occurred. Check the contents of the carton. The contents should agree with the information listed on the packing list. Report any discrepancy to the carrier and the factory immediately.
TO ORDER PARTS: Call 1-800-548-3373 or 479-636-5776. Be sure to give the serial number to the Service Department personnel. The Mart Cart serial number is located on the seat support tube under the seat as shown in parts list portion of this manual.
TERMS: All parts will be shipped with approved credit card, check in advance or C.O.D. Commercial accounts are allowed 15 day terms from date on invoice with approved credit.
FREIGHT: All freight will be paid by the customer. Special consideration will be given to items under warranty coverage.
ATTENTION: It is the responsibility of the owner of this cart to maintain the cart in a safe and reliable operating condition at all times.
NOTE: Specifications found in this manual subject to change without notice.

IMPORTANT SAFETY INSTRUCTIONS

Please read before operating.

WARNINGS

  • Never attempt to charge the battery in this cart without using an electrical outlet that is protected by a GFCI.
  • Replace charging cord if plug is damaged or if the cord is worn or frayed. Never use the charging cord without proper grounding. Do not use if plug does not have three prongs.
  • Never allow the cart to be used out-of-doors or on any surface that is not level.
  • Always disconnect power before servicing.
  • See “Daily Maintenance Checklist,” and follow instructions.
  • Cart can roll. Enter and exit cart with care.
  • Replace parts using only factory-specified, original equipment from the manufacturer for your specific model. Failure to do so may void warranty, affect operation of the cart, and result in injury.

OPERATING PROCEDURES

  • New carts will need charging! Charge batteries for 24 hours prior to first use.
  • THIS CART IS FOR USE INDOORS ON A FLAT, LEVEL SURFACE ONLY.
  • DO NOT STAND ON CAR0T. (See “Operating & Warning Instructions” on cart).
  • After battery is charged, disconnect power supply cord BEFORE operating cart.
  • DO NOT exceed the load limitations as shown on the cart.
  • Return power cord to circular cavity when not charging
  • DO NOT allow children to operate or play on cart. Keep cart secured with key (if applicable), at service counter.

DAILY MAINTENANCE CHECK LIST

For optimum cart availability and performance, the following items should be checked daily:

  • ELECTRIC CORD —Replace cord if cord is worn or frayed, 3-pronged plug is broken or reel (optional) will not retract. Be sure power outlet provides protection through an operating “Ground Fault Circuit Interrupter” (GFCI).
  • SEAT AND MOUNTING —Tighten if necessary. If cracks or rust occur, or if seat rocks loosely, replace at once.
  • SEAT SWITCH —Test and replace if not working properly. Cart must stop when weight is removed from seat.
  • THROTTLE —Test for smooth “start, acceleration, deceleration, and stop.” Repair if necessary. Charge or replace battery if needed.
  • ANTI-TIP CASTERS —Replace if broken. Maintain height adjustment of 1/8” to 1/2” above floor level.
  • GENERAL —Repair or replace any component that may cause a potential safety hazard.
  • APPEARANCE —Wipe off and clean as needed for customer satisfaction and for store’s public image.

BATTERY CHARGING INSTRUCTIONS

Please read before charging.
Your cart is equipped with the Intelli-Charge™ system. While operating the cart, the LED will be solid green until the battery falls below 12.4 volts and then turns solid amber. When the battery charge falls below 10.5 volts, the LED will begin flashing red. The person riding the cart should have ample time to return the cart for charging. When the rider exits the cart, the horn will start beeping in unison with the red flashing LED. This will alert those responsible for maintaining the cart to plug in the charger. When plugged into a 120v AC wall socket, the LED will flash amber and the horn will silence. When charging is complete the LED will start flashing green. The charger may be left plugged in even longer as it will NOT harm the battery.

  • Install a Ground Fault Circuit Interrupter (GFCI) in the electrical circuit wherever the cart is to be charged. This is to protect against any possible shock hazard.
  • AC voltage required is 100-240 VAC (50/60 Hz). The current draw is 3.5 amps maximum.
  • Charge battery every night, all night, and at every opportunity. When the battery is fully charged, the charger will maintain a “float voltage” which will not damage the battery.
  • Do not allow the battery to fully discharge by skipping the nightly charging cycle. A fully discharged battery will take 7 hours to fully charge, so it is best not to let the battery become completely discharged.
  • Do not store the cart with a discharged battery. This can cause premature battery failure. Fully charge the battery at least every 30 days if in a low usage location.
  • No maintenance of battery is required. The AGM battery is maintenance free and water cannot be added.
  • NOTE: Under normal conditions, the battery will last more than 2 years or longer if the above recommendations are followed. Replace with original Mart Cart battery only. Mart Cart is not responsible for any adverse effects caused by replacement with any other type of battery.
  • IMPORTANT: Your cart has been equipped with an AGM (Suspended Electrolyte) Battery during the manufacturing process as original equipment. The manufacturer recommends that you replace the original battery only with the same type and rating to prevent damage to your cart’s internal components, charging system, or personal injury to you and your customer.

BATTERY REPLACEMENT INSTRUCTIONS

Please read before replacing battery.
Be Responsible! Recycle old battery or dispose of according to local or national codes. See next column, under DISPOSAL.
To Replace Battery: (Read precautions on batteries, under Charging Instructions and Safety Precautions, to avoid any sparks)

  1. Turn off key switch (if equipped, or flip On/Off switch to “Off” position). Disconnect charger cord from wall outlet, if plugged in.

  2. Reach under right rear of back cover and pull latch, then tilt chair forward.

  3. Remove rear cover.
    CAUTION: Do not cross battery posts with metal object!

  4. Remove old battery and place new battery.

  5. Before reinstalling cover, check wheel condition, and general condition of the chair.

  6. Reinstall rear cover and tilt chair back.

  7. Test cart for proper operation. Charge battery if necessary.

ADDITIONAL INFORMATION

  • SEAT LOCK
    For XTi 12 with sliding seat. The seat lock and the chair should be inspected daily for proper function. The release/locking arm should move freely and spring back into locking position. If return spring is broken, DO NOT USE cart until spring is replaced.

  • SEAT SWITCH
    The seat switch is located under seat. Pressure (weight) on the seat closes the control circuit, and allows the cart to operate.

  • VARIABLE SPEED CONTROL
    The cart’s speed is regulated by a potentiometer. This provides extremely smooth acceleration from 0 to 2.2 MPH, and is located in the control box on the steering column.

  • CIRCUIT BREAKER
    The circuit breaker is designed to protect your electrical system from transient overloads or electrical shorts. Either could cause serious damage without a circuit breaker to open the circuit. The circuit breaker is a manual reset type. It requires manual resetting once it has been tripped.

  • CHARGING
    HOW IT WORKS: When the power supply cord is plugged into the store’s electrical outlet the battery charger is energized. The charger sends approximately 14.5 volts to the battery for charging. A third wire (yellow) from the charger output inhibits the PWM until the power to the charger is disconnected. The motor circuit is interrupted until charging is complete. NOTE: The cart will not move under power when the battery is being charged. If the cart moves while plugged in, check the power to your outlet before calling for service.

  • CONTROL BOX
    The master control box is located on top of the steering column. It contains the RUN/STOP/HORN switch, and key switch (optional keyless system available). The cover can be removed by removing the four bottom screws. Our models are equipped with the Intelli-Charge™ system, a bicolor LED can be found in the RUN/STOP/HORN switch.

Control Box Parts List

mart cart 280-5563 Electric Shopping Cart-FIG2

DECALS FOUND ON MART CART® ELECTRIC SHOPPING CART

Please call 1-800-548-3373 if your decals are missing or are needing replacement.
Standard decals and signs are English and Spanish (see part numbers below). Call for other languages.

DAILY MAINTENANCE CHECK LIST
For optimum Cart availability and performance, the following Items should be checked daily:

  1. ELECTRIC CORD and/or REEL . Replace cord andior reel if cord is worn or frayed, 3 pronged plug is broken or reel will not retract. Be sure Power-Outlet provides protection through an operating Ground Fault Circuit Interrupter (GFCI).

  2. SEAT & MOUNTING – Tighten if necessary. I cracks or rust occur, or if seat rocks loosely, replace at once.
    Lubricate swivel or tracks with vaseline as required. Make sure Seat Lock is in good working condition.

  3. SEAT SWITCH – If eart is equipped with a seat switch, test and replace if not working property.
    Cart must stop when weight is removed from seat.

  4. THROTTLE – Test for smooth “start”, acceleration, deceleration and “stop”. Repair if necessary. Charge or replace

  5. ANTI-TIP CASTERS – Replace if broken. Maintain height adjustment of 1/8° to 1/2° above floor level.

  6. GENERAL – Repair or replace any component that would cause a potential “Safety Hazard”.

  7. APPEARANCE – Wipe off and clean as needed for customer satisfaction and for store’s “Public Image”.

PATENTED
U.S. PATENT NO. 7108090 B2

WARNING
PLEASE READ TO AVOID PERSONAL INJURY.
USE AT YOUR OWN RISKI INTENDED FOR USE INDOORS ON LEVEL SURFACE ONLY!

  1. Read operating instructions or ask for assistance before using.
  2. Use extra caution getting “ON” or “OFF” cart.
  3. Cart is on wheels and may roll.
  4. You must be seated to operate cart.
  5. Keep feet and legs inboard while operating.
  6. Do not stand on cart.
  7. Do not lean “ON” or “OVER” the side of the cart.
  8. NO CHILDREN IN BASKET.

OPERATING INSTRUCTIONS

PLEASE READ BEFORE OPERATING

  1. Turn key on and/or press the “Run* switch.
  2. Thumb levers rotate to power the cart. Press top lever forward to go forward. Press bottom lever down to go in reverse.
  3. To stop, release the thumb levers andlor press the ‘stop” switch.
  4. If needed, ask cashier for assistance to get your items to your vehicle. Under no circumstances are carts to be taken outside the store.

mart cart 280-5563 Electric Shopping Cart-FIG3 mart cart 280-5563 Electric Shopping Cart-FIG4 mart cart 280-5563 Electric Shopping Cart-FIG5

PEODUCT IDENTIFICATION

mart cart 280-5563 Electric Shopping Cart-FIG6

Item Part No. Description
1 280-1818 Main Frame (280-1820 with bumper)
2 000-1224 5/8” Bushing (2 on each wheel)
3 280-1877 8” Wheel, Poly-U
4 029-0047 Snap Ring
6 280-1261 Seat Mount Tube
7 280-1799 Fuse, 5 AMP Mini
8 280-1228 Circuit Breaker, 15 AMP
9 280-0006 Mart Cart 24” Seat
10 280-1264 Basket Tube (see options pg. 6)
11 200-1802 Basket, LIL Max (see options pg. 6)
12 200-1236 Basket Mounting Clip (4)
13 200-1052 2” Caster
14 280-2012 Hub Motor/Wheel/Tire, GREEN
15 see pg. 3 Steering Column
16 280-1214 Battery, 35 Ahr
17 200-1553 Seat Switch
18 280-1936 12 VDC Charger – 10 AMP
Item Part No. Description
--- --- ---
19 280-1712 Main Wire Harness/Battery Cover Assy.
20 280-1943 Steering Wire Harness w/Connectors
21 280-1281 Floor Cover
22 280-1280 Rear Cover (select color option)
23 280-1279 Front Cover (select color option)
24 280-1711 Spring Latch for Seat
25 280-1935 Motor Controller
26 280-1646 Wire Harness (see note) Controller to Motor
27 280-1269 Fork Assembly
28 280-1441 Bridge Cover
29 280-1346 Tire/Outer Shell
30 280-1797 Charging Cord, coiled
31 280-1626 Wire Guide (see note)
32 280-1840 Rear Bumper
33 see pg. 3 Control Box
34 280-1614 Basket bumpers (gray)
35 280-1637 Cord Cover (see note)
36 280-0093 Bushing, Spacer
37 280-1659 Cord Cover Lid (see note)

NOTE: #31 (wire guide) and #26 (wire harness) can be ordered as an assembly part 280-1656

35 (cord cover) & #37 (cord cover lid) can be ordered as an assembly part

280-0004

Optional Parts

mart cart 280-5563 Electric Shopping Cart-FIG7

Electrical Schematic

When this cart is equipped with controller 280-1569, use this schematic.

mart cart 280-5563 Electric Shopping Cart-FIG8

MATERIAL SAFETY DATA SHEET

mart cart 280-5563 Electric Shopping Cart-FIG9 mart cart 280-5563 Electric Shopping Cart-FIG10

115 E. Linden • Rogers, Arkansas 72756 USA 479-636-5776 • Fax: 479-636-3245 International (001) 479-636-5776
www.martcart.com
800-548-3373
MC1-MODEL-5563-OM-191101-EN

Specifications are subject to change without notice .

Printed in the USA.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals