TrendPet Dog Bed High Bed Instructions
- June 12, 2024
- TrendPet
Table of Contents
HIGHBED
HighBed – Instruction Manual | v 1.0
General information
Dog Bed High Bed
It‘s that simple! Setup video
http://trendpet.de/deeplink/highbed_instructions
General information
2.1. Preface
Thank you for choosing the TrendPet HighBed. Please read this manual carefully
before you assemble and let your dog use the HighBed. Keep these instructions
so that you can refer to them at a later date if necessary.
2.2. Important information on the operating instructions
By attentively reading these operating instructions, the correct assembly of
the HighBed as well as the correct handling in day-to-day life can be ensured.
Thus, hazards to people and your pet can be avoided. Your safety and that of
your dog is our top priority.
Safety instructions
3.1. Symbols used
In this operating manual, attention is drawn at various points to special
dangers and recommendations for action. These notes are marked accordingly.
Notice!
This symbol indicates improper use which may result in damage to the product.
Caution!
This symbol draws attention to dangers in connection with the use of the
product, which may affect the physical well-being of humans and animals if not
observed.
3.2. Checking for rough edges
Before first assembly, inspect your HighBed for sharp edges that may occur
despite considerable care taken during the manufacturing process. In
particular, inspect the open ends of the tubes that are to be installed.
Caution
All components of the HighBed are checked
for safety, however, burrs or sharp edges may occur at the joints during the
manufacturing! process. These can cause cuts if care is not
3.3. Risk of pinching
There is a risk of pinching or bruising limbs, such as fingers and hands,
during assembly of the individual components.
Caution!
The individual components of the HighBed are securely joined to each other.
If you slip or are inattentive while assembling the product, there is a risk
of injury. We recommend that you carry out the assembly with a second person
to facilitate the assembly.
3.4. Wear and environmental influences
Do not expose the HighBed to unusually strong environmental influences such as
permanent wetness, rain or frost.
The HighBed could otherwise sustain permanent damage.
3.5. Intended use
The HighBed is only to be used as a place for dogs to rest and sleep. Please
observe the permissible total weight. The maximum load capacity can be found
in the table in section „Page 9 – 3.6. Key data“. The HighBed is not designed
to be used while traveling in a car, camper or caravan! Do not use the HighBed
as a trampoline – it is not in any way suitable for this purpose.
3.6. Key data
| Properties: | S | M | L | XL |
|---|---|---|---|---|
| Outer dimensions (LxWx H) | 75 x 55 x18cm | 90 x 70 x 18 cr | 105 x 80 x 18cm |
125 x 90 x18 cn-
Lying surface (LxW)| 65 x 45 cm| 80 x 60 cm| 95 x 70 cm| 115×80 cm
Height| 18 cm| 18cm| 18cm| 18 cm
Weight| 2,9 Kg| 3,45 Kg| 4.0 Kg| 4,45 Kg
Maximum shoulder height| up to 40cm| up [040 -50cm| up to 50-60cm| up to 60-
65cm
Maximum load| 80 Kg| 80 Kg| 80 Kg| 80 Kg
Overview of your HighBed
4.1. Which items are included in the package?
Abb. 11.3.2. Which items are included in the package?
4.2. Which part is where on the HighBed?
A 8 M8 countersunk screws 55 mm
B 4 M5 cylinder head screws 23 mm
C 4 upper components for the corners
D 4 lower components for the corners
E 4 tubes for the feet
F 4 rubber pads
G 1 net for the lying surface
I 2 middle stainless steel bars
J 2 long stainless steel bars
K 2 medium tubes for the frame
H 2 long tubes for the frame
Quick guide
Assembly
6.1. Required tools
You will need the following tools for the assembly of the HighBed:
6.2. Unpacking the HighBed
Open the box of the HighBed and remove the individual components. Make sure
that all screws and components are within reach of you during assembly.
6.3. Preparing for assembly
Before starting the assembly, place a folded blanket
under the components of the HighBed. This will prevent damage or scratches to
the HighBed or your floor covering during the subsequent assembly process.
6.4. Preparing the lying surface
Start the assembly of the HighBed with the lying surface. To do this, take the
black net (Ref. G) and insert the stainless steel rods (Ref. H|Ref. I) into
the net pockets provided at the ends of the net.
6.5. Connecting the lying surface to the tubular frame
When assembling the tubular frame andthe net, the orientation of the net plays
an important role:
Make sure that the seamed over ends of the pockets with the stainless steel
rods are on the bottom side of the net
Now insert the long side of the net with the stainless steel rod into the keder guide of the long aluminium tube branded with the TrendPet logo (Ref. K). Make sure that the logo is visible the right way around.
Now take one of the medium length aluminium tubes (Ref. J) and insert the shorter side of the net with the stainless steel rod into the keder guide of the tube for the frame.
Repeat the above steps until the four sides of the lying surface are connected with the matching tubes.
6.6. Mounting the corner brackets
After you have connected the four tubes to the lying surface, now mount the
corners.
Start with any corner. Take the lower corner piece (Ref. D) in your hand and
insert the two tubes into the component.
On the inside of the corner piece you will find a circumferential taper (see Fig. 6.6.2.), which provides the stopping point for the tube. Make sure that you push both tubes all the way to the stop (See Fig. 6.6.3.). This will ensure that the holes for the screws are correctly aligned.
As soon as both
tubes are in the lower corner piece, you can remove the upper part of the
corner piece (Ref. C) (See Fig. 6.6.4.). Once the upper half of the corner is
correctly positioned, you can fix it with the enclosed M8 countersunk screws
(Ref. A). Screw them only loosely into the thread to facilitate further
assembly.
Insert the screws from above through the holes provided. Make sure that the holes of the upper part of the corner joint and those of the tube overlap exactly.
IMPORTANT:
To make the assembly as easy as possible, make sure to screw all screws of the
tube frame only loosely (approx. 3 – 4 turns) into the thread at first. This
way, each corner still has a little play at first. This procedure makes it
easier for you to insert the two tubes into the remaining corner piece:
6.7. Mounting the last corner
To keep the lying surface wrinkle-free, the net has been sewn to fit the frame
precisely.
Therefore, the last corner is a little harder to press into the guide when
first assembled.
To make it as easy as possible, please proceed as follows:
First, place the bottom corner piece (Ref. D) in your palms (See Fig. 6.7.1.).
Now bring the corner in line with the two tapers of the open tube ends (See Fig. 6.7.2.).
Then place both thumbs on the tube frame and press the tubes firmly along the
taper into the corner component (see Fig. 6.7.3.).
When the tubes are in the lower corner component, reassemble the upper part of
the corner and fasten both with the screws (Ref. A).
6.8. Tighten screws
Once all four corners are mounted, you can tighten the screws accordingly. To
do this, place the frame on a flat surface and tighten the screws in a
crosswise pattern. This procedure ensures a safe, tilt-free and straight stand
of your HighBed.
6.9. Mounting the feet
To assemble the feet, first turn the completed tubular frame upside down and
place it on a flat surface. Now take the enclosed short tubes (Ref. E) and
insert them into the corner components with the groove facing the lying
surface.
Then fix the tube with the M4 screw (Ref. B).
Finally, place the end cap (Ref. F) on the previously mounted tube.
6.10. Finished assembly
The HighBed is now completely assembled.
Have fun with your HighBed.
Service & Maintenance
7.1. Cleaning
The frame as well as the net of the HighBed can be cleaned with a damp cloth
and mild detergent.
Notice!
Cleaning the HighBed with aggressive detergents can cause damage to the
HighBed.
7.2. Maintenance Retighten screws
If necessary, the screws of the HighBed must be retightened. Check regularly
whether the HighBed is still stable and the screws are tight.
Check the net
Check occasionally whether the net of the lying surface is still intact or
shows traces of wear.
Spare parts
The HighBed has been developed over many years and the individual components
have been carefully calibrated to each other.
Proper use can only be ensured with original spare parts.
Troubleshooting
| Error description | Possible causes |
|---|---|
| The frame or the stand of the HighBed are loose. | The screws have come loose |
and need to be retightened.
The components have not been assembled to fit accurately.
The HighBed no longer has a firm stand and is wobbling.| The screws have come
loose and need to be retightened.
The frame has warped.
Place the HighBed on a flat surface and gradually loosen all the screws of the
corners. Adjust the bed with light pressure on the lying surface and tighten
the screws again.
The rubber feet are worn or missing.
The net is torn.| The net was overloaded.
There have been sharp objects on the net. The net has been pierced with o
sharp object and has subsequently torn further.
In this case a replacement net can help. Please contact us by phone or e-mail
Disposal
10.1. Disposal of the packaging material
Recycle the packaging material in accordance with your local regulations.
Separate cardboard and paper from plastic and foam and dispose of the
materials for recycling.
10.2. Disposal of the HighBed
The dismantled HighBed can be fed into the recycling chain separately sorted
by its respective material.
Imprint
11.1. Manufacturer & Distributor
The manufacturer of the HighBed dog bed is
TrendPet, a brand of Rewer GmbH. For the European Union, Rewer GmbH is the
distributor of the goods.
11.2. Enterprise
TrendPet
Rewer GmbH
Siemensstr. 11
48565 Steinfurt
Germany
11.3. Contact
Tel.: +49 (0) 2552 99 710 560
Fax : +49 (0) 2552 99 710 599
E-Mail:service@trendpet.de
Internet:www.trendpet.de
Misprints and errors reserved.
Documents / Resources
|
TrendPet Dog Bed High
Bed
[pdf] Instructions
Dog Bed High Bed, Dog, Bed High Bed, High Bed, Bed
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>