Shenzhen Weiteshijia Technology Co Ltd AX-213 Quicksand Desk Lamp User Manual

Shenzhen Weiteshijia Technology Co Ltd AX-213 Quicksand Desk Lamp

Wireless charging instructions for use Specification parameter

• Material: Metal +ABS+ silicone + components+ glass
• Type number: AX-213
• Input: 5V=2A,9V=1.67A
• Wireless output lSW compatible with lOW/7.SW/SW
• Charging efficiency: about 78%
• Lighting power: 2.5W
• Working frequency: 105~205KHZ
• Product size: 2S9.626cm
• Gross weight: 1000g
• Implementation standard: GB7000.204-2008
  GB/T 37687-2019

Inspection: qualified
Place of Origin : China

Product characteristics

• Fun decompression 3 D quicksand painting
• Wireless fast charge
• Touch lighting night light

Lighting specification

•  Touch to switch lighting sequence: white light – warm light — yellow light — off.
• Adjust the brightness of the light
  Long press to increase the brightness, and long press again to reduce the brightness.

Wireless instructions

• This product supports adapters with QC2.0\QC3.0\PD\AFC charging protocol and can use adapters with an output power of SV2A,9V2A,12Vl.5, and above.

• This product supports up to wireless 15W fast charge output, backward compatible with lOW 7.SW SW;
  Wireless SW output is supported when using an SV2A adapter;
  When using 9V2A,12Vl.SA or above adapters, it can support 7.5W/10W, and support a maximum of lSW output. In ord_er to ensure the normal charging of the mobile phone, please clear the obstacles on the surface of the charging area and ensure that the charging area of the mobile phone corresponds to the position of the transmitting coil of the product.The charging distance should be less than 8mm.

• This product has over-temperature, over-voltage, over current protection, foreign body detection, and other functions to ensure safe charging; Wireless charging function: Support Apple 1Phone12 13 14 full series wireless charging, support Huawei, Samsung, Apple, LG, Xiaomi, and other series of mobile phone wireless fast charging;
  Support lSW backward compatible wireless charging full range of mobile phone charging.

Note

1. In order to ensure the normal use of the product, be sure to use a fast charge adapter with an output power greater than or equal to 10w.
2. When using the SVlA adapter, this product can use the light function alone, but does not support wireless output.

Product standard

• lamp *1,
• quicksand painting glass *1,
• fast charge line *1,
• manual *l.

Applicable equipment

Smart charging compatible with major brands of QI standard mobile phones, as follows:

• Apple Series Ji Phone X iPhone XR iPhone XS iPhone XS Max.
• Samsung Series /Galaxy 56 Galaxy S7 Galaxy S8 Galaxy S9 Note 8 Note9.
• Huawei Series /Mate RS Mate 20Pro Mate 20RS P30 Pro.
• Mi Series /MIX 25 MIX 3 MI9.

Matters needing attention

• Do not use or store the product in direct sunlight or high temperature for a long time.
• Do not charge too close to magnetic cards, magnetic recording media and sophisticated instruments. Do not disassemble or modify this product.
• Do not touch the adapter with wet hands.
• Keep this product away from water or other liquids.
• If you want to clean this product, disconnect the power supply.
• Do not place the product on a plane with an inclination greater than 6 degrees to prevent toppling.
• The light source of this lamp is not replaceable, and when the light source reaches the end of its life, the entire lamp should be replaced.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

Radiation Exposure Statement

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>