BRISTAN NAP BAS C Napoli Basin Mixer with Clicker Waste Chrome User Guide
- June 12, 2024
- BRISTAN
Table of Contents
Installation Instructions & User Guide
Please leave these instructions
with the end user
NAP BAS C (D1)
Specifications
Dynamic Water Pressure
Maximum Static Pressure: 10.0 bar
Inlet Water Temperature
Maximum Hot 60°C
Inlet Connections
1/2” BSP
Flexible Tails
Spare Parts
To replace any spare parts for your tap, why not scan the QR Code or visit www.bristan.com and search for your product.
Pack Contents
Operation
Tools Required for
Installation/ Maintenance
Prior to Installation
All products manufactured and supplied by Bristan are safe to use provided
that they are installed, operated and receive regular maintenance in
accordance with these instructions.
This product needs to be installed in accordance with, and meet the
requirements of the Water Supply (Water Fittings) Regulations (Northern
Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014.
For full Installation Requirements & Notes (IRN) please visit
https://www.wrasapprovals.co.uk/approvals-directory/
Isolation valves must be fitted to the inlet water supplies to ensure ease of
future maintenance.
Before installing this product the water supply must be thoroughly flushed in
order to remove any swarf, solder etc.
Full access must be made available for future maintenance/servicing purposes.
This product must not be modified in any way as this will invalidate the
guarantee.
Important
The images shown are for illustrative purposes only.
The tap you have purchased may look different to those pictured in this
booklet but will follow the same installation steps.
Your contents page will be specific to your product.
If you find your product or any of its components differ from those shown on
the contents page, please contact our customer support.
Installation
Screw the threaded tail
into the base of the tap body until it stops, ensure the threaded tail is the
correct way up with the thread break at the top
Screw in the flexible tails by hand only
DO NOT OVERTIGHTEN Your model may come with a plinth and will either
be included pre-attached or loose in the box* 
If required, thread the flexible tails and fixing
kit rods through the plinth and rubber seal (if loose) and align with tap body
Look for any grub screw holes on the plinth as these may be required to fix it
to the tap body (these can be located underneath the rubber seal)
Thread the flexible tails
through the basin hole
If the hole is not large enough for both tail ends to fit through, unscrew one
of the flexible tails and screw back in from underneath the basin 
From underneath the
basin, slide the rubber washer around the threaded tail and begin to tighten
the backnut upwards
Waste Installation and
Operation
Fit the waste above the basin ensuring the washer is in place.
Push waste into hole until
the outer rim sits flush with the bottom of the basin.
Then place the washer from underneath and tighten the
backnut to secure the waste to the basin.
Push the centre down to close the waste.
Push again to openand release contents of basin.
Your waste is now ready for use.
General Cleaning
Bristan products are made from premium materials, with hand polished,
electroplated, PVD or EPD finishes
Your taps or shower should be regularly cleaned with warm water, a mild pH-
neutral liquid soap, and polished with a soft cloth.
Any residues from soap, toothpaste, shampoos and shower gels can cause
blemishes if not rinsed off straight after use.
Household bleaches and cleaners contain harsh chemicals and may damage the
surface finish. Avoid using abrasive cloths, scouring pads, scrub sponges,
steel wool or anything similar.
Maintenance – Cartridge/ Valve Replacement
Remove indice by pulling it loose, then undo hex grub screw to remove
handle.
Remove the shroud and retaining nut and then lift the cartridge out of the tap
(Some shrouds may need to be unscrewed by hand before removing)
Reverse the steps to replace the cartridges/ valves and handles.
Maintenance – Clean/ Replace Outlet
Flow Straightener
Using an adjustable spanner, unscrew gently to remove the outlet.
If
your model comes with one, insert the key tool into the outlet and twist to
release it.
Recessed Outlet Using a coin, insert into the slot on
the outlet and twist to release it.
Coin Slot Aerator
Check all loose parts for any damage, then soak using a suitable solution
to de-scale. Reverse the steps to replace the outlet
Love Your Chrome
Bristan offers an effective chrome-friendly cleaning kit for use with your
taps and showers. Scan the QR Code or search for ‘CLEAN KITOT” on
www.bristan.com.
Troubleshooting
| Symptom | Cause | Remedy |
|---|---|---|
| Low Flow | Partially closed isolation valve. | Open isolation valve. |
| Airlock or partial blockage in the supply pipework. | Flush through pipework to |
ensure removal of debris and any airlocks.
Partial blockage in the outlet| Remove to Clean and soak in suitable solution.
No hot water or cycling hot and
cold| Instantaneous water heater cycles on and off as flow rate or pressure is
too low.| Increase water flow rate or pressure through system.
No Flow| Closed isolation valve.| Open isolation valve.
Mains water supply turned off.| Turn on mains water supply.
Temperatures not corresponding
with taps| Inlet pipes have been connected incorrectly| Swap the inlet tails
around.
Notes
Please use this space for any notes you or your installer may have regarding
the installation/plumbing of this product.
Contact Us
Bristan Group Ltd.
UK: Bristan Group, B78 1SG.
EU: Masco Europe S.ar.l.
14 Rue Strachen
6933 Mensdorf
Luxembourg
Customer Service: +44330 026 6273
Web: www.bristan.com
Email: enguire@bristan.com
A Masco Company
Servicing Your Tap
We recommend servicing your tap at least once every year to prolong its
life.
To see a video showing how to remove the cartridge for servicing, scan the QR
code with your smart phone or tablet.
Alternatively visit www.youtube.com/BristanTV
Our Guarantee
At Bristan, we want to make things as easy as possible for our customers.
That’s why we offer solid guarantees on all our products, effective from the
date of purchase, to give you peace of mind.
Your guarantee starts from the purchase of your product, but you can still
benefit from registering it for easier identification in the unlikely event of
a manufacturing fault, please visit
www.bristan.com/register
For any other queries, please call Customer Service on 0330 026 6273 where our
expert team of advisors will be able to offer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service-
centre/guarantees.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>