JOCEL JAT011893 Patio Heater Instruction Manual

JOCEL JAT011893 Patio Heater

Introduction

This appliance is intended for decorative purposes
For Outdoor use only!
Warning: Accessible parts may be very hot, keep young children away.
This appliance must be installed in accordance with the rules in force, and used only in a sufficiently ventilated space.
Consult instructions before installation and use of this appliance.
Read the instructions before installing and using the appliance.
IMPORTANT : RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

SPECIFICATION

mbar / G31 at 37 mbar

| 28-30mbar| 28-30mbar| 50mbar
Type of gas| G30/G31| G30, G31 or their mixtures| G30| G30, G31 or their mixtures
Nominal Heat input (kW) (Hi)| ∑Qn Maxi mum| 8.0| 8.0| 8.0| 8.0
Minim um| 4.0| 4.0| 4.0| 4.0
Gas Consumption (g/h)| Maxi mum| 631| 631| 631| 631
Minim um| 315| 315| 315| 315
Ignition system| Battery electric igniter
Gas regulator| Certified regulator according to EN 16129 (flow rate: max. 1.5kg/h)
Gas hose| Certified gas hose according to applicable EN-standard (max0.5m)
Gas Container| Up to 15 kg [at maximum 32 cm (dia.) x 56cm (H)]
Gas connection size| 8mm| 8mm| 8mm| 1/4
Destination countries| BE, FR, IT, LU, IE, GB, GR, PT, ES, CY, CZ, LT, SK, CH, SI, LV| LU, NL, DK, FI, SE, CY, CZ, EE, LT, MT, SK, SI, BG, IS, NO, TR, HR, RO, IT, HU, LV| FR, GB, IE, PT| DE,AT,CH,SK

This appliance was designed and made in accordance with EN 509:1999+A2:2004（full test） & EN14543: 2017（partly test, Clause 5.9 & 6.3.2.5.
This appliance complies with the prescriptions of Gas Appliance Regulation 2016/426/EU.

SAFETY WARNINGS

WARNING:

• Do not modify the appliance;
• Do not move the appliance during use;
• Turn off the gas supply at the gas container after use
• Accessible parts may be very hot. Keep young children away
• The appliance should not be used in basements or below ground level.
• The appliance must only be used for space heating.

WARNING:
THIS APPLIANCE HAS A NAKED FLAME; A SUITABLE GUARD SHOULD BE USED FOR THE PROTECTION OFYOUNG CHILDREN, THE ELDERLY AND THE INFIRM

DANGER

| CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car or home.
---|---

This symbol is stick on in the higher part of the appliance (do not remove it).

Attention : Surface very hot! Do not touch!!!!

ATTENTION : This appliance uses flexible gas hose, clamps and regulator that must be used (not supplied); use always these accessories in accordance to the National Rules in force of the country of destination.
These components should be periodically substituted, according to the date reported on the body of each of them, or according to the National Rules in force of the country of destination.
Gas regulator and hose are not included, you have to buy them from local gas suppliers.
Before installation, ensure that the local distribution conditions (identification of the type of gas and pressure) and the adjustment of the appliance are compatible.

GAS FIRE PLACE SAFETY WARNINGS

“The appliance must be installed according to the instructions and National Rules in force of the country of destination”

• Read the instructions carefully before using this appliance – Never use this appliance indoors, on vehicles or boat.
• If the instruction of this manual are not exactly followed, dangerous situation may come up; make sure all parts are in proper place.
• Any modification of the appliance may be dangerous; improper installation, adjustment, alteration, service or maintenance may cause personal injury or property damage.
• Installation and repair must be performed by a Qualified Service, Agency or Gas Supplier; never do it by your-self!
• Never use this appliance until all connections have been leakage tested. Never put it into operation if any leakage is detected; check leakage all the time by soapy foam (never using a flame). In case of gas leakage, appliance shall not be used; shut-off gas supply and the appliance must be investigated and rectified by Qualified Service, Agency or Gas Supplier before it is used again.
• Appliance must be attended all the time while in operation and never attempt to disconnect gas regulator or gas fittings.
• This is a decorative appliance only and any kind of cooking is strictly forbidden. Never use charcoal or any other solid fuel but lava rocks supplied with the appliance.
• Do not burn rubbish and any other materials throw on this appliance; do not pour water into the appliance.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• Use only gas type (see adjustment in “Specification” section and also Appliance Marking on the appliance) specified by the manufacturer.
• Use only LPG cylinder specified by the manufacturer (see in “LPG cylinder”).
• Shut-off the valve of the LPG cylinder or the gas regulator before moving the appliance.
• Do not move the appliance during use; once it has been turned in “OFF” position (full disk), wait temperature has cooled down (at least 30 minutes).
• Gloves are strictly recommended to be used while moving this appliance, to protect your hands.
• Always use the appliance on a horizontal not combustible surface to keep it stable.
• Check that the gas regulator seal is correctly fitted and able to fulfil its function.
• Turn off the gas supply at the LPG cylinder after use.
• Flexible metal or rubber pipe, used to connect the appliance with the LPG cylinder must be changed within the prescribed intervals and according to the National Rules in force (see expiry date on the flexible metal or rubber pipe).
• Check flexible metal or rubber pipe used at least once per month and while LPG cylinder is changed; if it shows sign of cracking, splitting or deterioration, it shall be exchanged for a new one of the same length and of equivalent quality.
• The appliance should be inspected before using and at least one time a year (see “Maintenance”).
• A temperature less than 5 ˚C will cause restricted gas flow and the appliance will not work properly.
• Battery ignition (not supplied) may contain mercury; do not put in fire or trash. After use, handle as recycle hazardous.
• Take battery (not supplied) out when appliance is not supposed to be used for a long period of time.
• Warning: accessible parts may be very hot. Keep young children away.
• People should be warned of the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
• If fire should go out, turn gas supply in “OFF” position and wait for 2 minutes before attempting to relight.
• Children should be carefully supervised when they are in the area of the appliance; never let them to use this appliance.
• Clothing or other flammable materials should not be hung from the appliance, or placed near the appliance.
• Always maintain at least 1m clearance from combustible materials (left or right side and back wall); any ceiling is forbidden.
• “This appliance must be kept away from flammable materials”.
• Do not put any other fireplace cover or anything flammable on, beneath or beside the appliance.
• Do not rest feet on appliance while in operation.
• Keep any electrical supply cord and rubber pipe away from any heated surface.
• Any sealed parts by Manufacture or his agent cannot be altered by the user.
• These instructions are only valid if the country symbol appears on the instruction manual and on the appliance. If this code is not present on the appliance it is necessary to refer to the technical instructions which will provide the necessary information concerning the modification of the appliance to the condition of use for the country.
• This appliance shall be used ONLY outdoors in a well-ventilated space and shall NOT be used inside a building, garage, or any other enclosed area. For use outdoors or in amply ventilated areas. An amply ventilated area must have a minimum of 25% of the surface open area. The surface area is the sum of the walls surface.
  

INSTALLATION

ASSEMBLY
This Gas Fire place must be installed on flat, stable surface, away from any combustible materials or construction.

Warning : When the heater be assembled to the legs, the table shall not tilt over when placed in the most unfavorable position on a 10° inclined plane.

• Place the lava rocks on the burner and around the burner evenly, then tight. Put on top of the lava rocks the 3 pcs of decorative wooden. (See the pictures 10 and 11)
  

Warning : Lava rocks can’t cover the ignition hook.

• Unscrew the button cap of ignite, put a piece of AAA (not supplied) battery into ignite compartment with anode outward, then screw the button cap (see picture 12)
  

INSTRUCTION FOR CONNECTING GAS CIRCUIT TO LPG CYLINDER :
Keep at hand suitable crossed screwdriver, adjustable spanners, pliers and wrenches. Before assembly, make sure all protection packing material has been removed. You need to purchase one gas regulator and one gas cylinder. The gas regulator has to be set according to National Rules in force for specific gas category (see on page 2) and proper gas consumption (g/h) specification. The LPG cylinder should be standard one. Recommend to use 15kg. Replacement must be that specified in “Gas Requirements” section of this Instruction Manual. Be careful: do not kink flexible gas rubber pipe of gas circuit. If pipe holder should not be provided, thread of the gas inlet connection will be in line with Standards ISO 7-1 or ISO 228-1, according to National Rules in force of the country of destination.

• Make sure appliance gas knob is turned “OFF” before assembling (see below Figure).
• Position the LPG cylinder at the side of your appliance, not underneath, keeping in mind that the LPG cylinder must be kept away from heat and in a safe position.
• Connect the regulator to LPG cylinder by hand
• Connect the hose to the appliance and the regulator. Tighten the screw of the hose clamp with a screwdriver.
  

OPERATING INSTRUCTIONS

LIGHTING

Before ignite the appliance, perform “Leakage Testing” in a well-ventilated area (outdoor). At first use and after every LPG cylinder substitution, appliance gas circuit must be purged of the inside air before igniting! To do this, turn the control knob counter-clockwise to the ignition position and push it holding for 1 minute before attempting ignition.

1. Make sure that LPG cylinder, full 4/5 its capacity, contains proper LPG Gas (refer to Technical Data on page 2). Turn LPG cylinder valve in full “ON” position and close LPG compartment panel.
2. Make sure that burner control knob is in “OFF” position.
3. Push the control knob and keep pressing while turning counter-clockwise to the corresponding low position (small flame). At the same time push the ignition button. Igniter will spark automatically (it is possible to ignite the appliance even with proper lit long match, approaching carefully the burner managing in the same way).
4. When the burner is lit in low position (small flame), stop pushing ignition button and keep the control knob pressed but not over 15 seconds to heat the thermocouple (FSD); then release it (first ignition take generally more time, because gas circuit is full of air).
5. If the burner does not keep lit, wait 1-2 minutes and then repeat steps 3 and 4.
6. Burner now is lit in Minimum position (small flame).
7. Adjust the heat input by turning the knob from the Minimum position (small flame) to the Maximum position, as properly.
8. After lighting, turn knob from Minimum to Maximum (big flame) position and back, to check flame stability.
9. In case of accidental break down of the flame (for wind or other reasons), FSD will shut-off gas supply automatically (FSD = Flame Safety Device) not over 60 seconds.
   Note : The burner may be noisy when initially turned on.
   If you experience any ignition problem consult the following “Troubleshooting”.

TO TURN “OFF” THE APPLIANCE

1. Turn appliance control knob clockwise up to “OFF” position.
2. Turn the LPG cylinder valve to the “OFF” position.
3. Allow the appliance to cool before moving it (at least 30 minutes).

RE-LIGHTING

1. Turn control knob to “OFF” position.
2. Wait at least 5 minutes, to let gas dissipate, before attempting burner re-light.
3. Repeat the “Lighting” steps.

LEAKAGE TESTING

Never check for gas leakages with a flame or while smoking.
This appliance needs to be periodically checked for leakages and an immediate check is required if the smell of gas is detected.

• Make a soap solution using 1 part of liquid dish-washing soap to 3 parts water. The soap solution can be applied with a soap bottle, brush, or rag to the leakage tested points shown in the figure beside.
• The valve of the LPG cylinder should be in the “OFF” position at this point of the leakage test. Once the soapy solution is applied to the gas connections, the valve of the LPG cylinder needs to be turned to the “ON” position.
• Soap bubbles will begin to form in the soapy solution if any leakage is present.
• In the event of gas leakage, the appliance shall not be used or if alight, the gas supply shall be shut-off and the appliance shall be investigated and rectified before it is used again. Tighten any leaking fittings, then turn on gas supply and recheck.
• If necessary, substitute gasket (according to EN 549 Class B2) or material used to guarantee tightness (according to EN 751-1 Class I).
  

GAS REQUIREMENTS

• Use only the type of gas and the type of LPG cylinder specified by the manufacturer.
• Appliance must use an approved gas regulator (approved for a working temperature not lower than 50 ˚C) according to the EN Standard EN16129 (gas regulator inlet and outlet connection according to the National Rules in force) and flexible gas rubber pipe according to applicable EN-standard (with proper inner diameter according to gas inlet connection and National Rules in force) with a length not over 1.5 m and approved for a working temperature not lower than 60 ˚C. When substitution will be necessary, you have to purchase suitable gas regulator, flexible gas rubber pipe and clamps from your local gas dealer; gas regulator should be substituted not over 10 years.
• Flexible gas rubber pipe must be located in the LPG compartment carefully, avoiding any twisting.
• Never use a damaged gas regulator.
• Never connect this appliance to an unregulated LPG source (gas regulator is mandatory to be used).
• When the appliance is not in use, turn the LPG cylinder in “OFF” position.
• Always perform a leakage test on gas connections whenever an LPG cylinder is connected. If bubbles form in the leakage test solution, do not use it. Never use a flame to test for leakages. It is strictly forbidden and dangerous!

LPG CYLINDER

• LPG cylinder used must be in accordance with the National Rules in force.
• LPG cylinder should have collar to protect cylinder valve and never filled over 80% its capacity.
• Refer to your gas supplier for instructions how to use and handle LPG cylinder.
• Never use an LPG cylinder with a damaged body, valve, collar or foot ring.
• Change LPG cylinders in an amply ventilated area, away from any ignition source (candle, cigarettes and so on).
• If appliance is stored indoors, detach and leave LPG cylinder outdoors in a ventilated and protected area.
• LPG cylinder must always be used in an upright position.
• Do not store a spare or disconnected LPG cylinder near this appliance.

IMPORTANT SAFETY RULES

This appliance is not fitted with “Atmosphere sensing device”.
To be used outdoors use only and in good weather condition (no rain, or windy condition).
The use of this appliance in enclosed areas can be dangerous and is PROHIBITED.
Children and adults should be aware of the high operating temperatures of areas above the post when operating this appliance. Children should be carefully supervised when in the vicinity of the appliance.
NEVER hang anything, including clothes or any other flammable items, on this appliance.
DO NOT operate this appliance unless it is fully assembled with all its parts.
Minimum clearance is 1 m from combustible materials and or any wall side (left, right or back); any ceiling is forbidden.
Appliance is not fitted with any guard; it is recommended to use one for the protection of young children, the elderly or infirm. The approach to the appliance is limited such that accessibility to the flame is minimized.
Do not stay too closed to the appliance while in operation.

MAINTENANCE AND CLEANING

To enjoy years of outstanding performance from your appliance, regular services of the appliance is mandatory as followings:

• The appliance should be inspected before at least one time a year by a Qualified Service only. More frequent cleaning may be required according to the use of the appliance.
• Keep exterior surfaces clean, free and clear from combustible materials.
• Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.
• While washing your unit makes sure to keep the area around the burner assembly dry at all times. If the gas control is exposed to water in any way, DO NOT try to use it. It must be replaced.
• Burner and LPG compartment circulating air passageways of the appliance must be kept clean.
• Airflow must be unobstructed. Keep controls, burner and circulation air passageways clean. Signs of possible blockage include:
• Gas odor with extreme yellow tipping of flame / Appliance glow is excessively uneven / Appliance makes popping noises.
• Spiders and insects can nest in burner or orifices. This dangerous condition can damage the appliance and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles.
• Carbon deposits may create a fire hazard. If any carbon deposits develop, clean dome and engine with warm soapy water.
• After the burner and lava rocks are completely cooled down, remove it from the bowl and use a soft brush to get rid of the mild stains, loose dirt and soil. Wipe with a soft cloth.
• Clean the bowl and afterward put lava rocks again in proper position.
• For proper cleaning, a vacuum cleaner can be used.

Note : In a salt-air environment (such as near the sea), corrosion occurs more quickly than normal. Frequently check the corroded areas and repair them promptly. Stubborn stains, discoloration and possibly rust pitting can occur from exposure to harsh outdoor conditions.
Be careful not let any powder or solvent come in contact with painted or plastic components as damage may occur.
After long use, some discoloration can come up and its screen is normal.
Make sure both gas supplies are in OFF position before changing battery. Please refer to the process of assembling battery (not supplied).
Please contact the Manufacturer or dealer for information regarding replacement hoses, thermocouples, igniters, lava rocks.

Attention : Never use unauthorized parts or component for this appliance.
Use only original equipment replacement spare parts and components.
Otherwise, may void the warranty of this product and result in a hazardous condition.

STORAGE (AFTER USE)

Turn control knob in “OFF” position.
Turn LPG cylinder in “OFF” position.
Store the appliance in a cool dry place away from direct sunlight; store it upright in an area sheltered
from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris).
If desired, cover to protect exterior surfaces and to prevent build up in air passages.
Note: Wait until appliance is cool before covering.
During periods of extended inactivity or when transporting:
Turn control knob in “OFF” position.
Disconnect LPG cylinder and move to a secure, well-ventilated location outdoors. DO NOT store in a location that will exceed 50 °C.
Store appliance upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris).
If desired, cover appliance to protect exterior surfaces and to prevent build up in air passages.
Note : Wait until appliance is cool before covering.

TROUBLESHOOTING

with a new one.
Blockage in the injector.| Clean or replace injector.
Air in the gas circuit.| Open gas line and bleed it (pressing control knob in) for not over 1 minute or until you smell gas.
Low gas pressure.| Replace LPG cylinder with a new one.
Igniter fails.| Use match to light burner; change battery or obtain new igniter and replace it.
Burner won’t stay lit| Dirty build up around burner.| Clean dirty around the burner.
Low flames or not full running around the burner.| Flame spreader holes partially closed; clean the burner.
Thermocouple is not operating correctly.| Replace thermocouple (FSD).
Low Gas pressure.| Replace LPG cylinder with a new one.
Burner flame is low
Note: Do not operate appliance below 5 ˚C| Outdoor temperature is greater than 5C and LPG cylinder is less than 25% full.| Replace LPG cylinder with a new one.
Gas pipe is bent or kinked.| Straighten hose and perform leakage test on gas pipe.
Control knob is fully Maximum position (big flame).| Turn control knob to ”OFF” position, let cool to room temperature and check burner and orifices for blockage.
Carbon build- up| Dirty or film on burner.| Clean burner.
Flash back (flame inside burner)| Burner ports are blocked.| Switch OFF the appliance. Close LPG cylinder valve. Wait 2 minutes, following the ignition procedure. Ignite burner. If problem continuous, switch-off. Contact your dealer.
Thick black smoke| Blockage in the burner.| Turn control knob to “OFF” position, let the appliance to cool at room temperature and remove blockage and clean burner inside and outside.

If you cannot solve trouble according to one of the mentioned solutions, please contact technical assistance.

GENERAL WARRANTY TERMS

1. The warranty is valid only on presentation of invoice of purchase.
2. This WARRANTY is limited exclusively to parts substitution ineffective due to faulty manufacture, made in our workshops.
3. The elimination of several faults of the scope of the guarantee is made for repair or replacement of defective parts, according to the discretion of our technical services. Defective parts are our property.
4. Are not covered under warranty damage caused by transportation, neglect or poor use, improper assembly or installation, as well as external influences such as: lightning strikes or power, flooding, humidity, etc..
5. Lose warranty, all appliances that are not being used according to the instructions or connected to FEEDING NETWORKS not guarantee a constant voltage of 220/240V.
6. The warranty does not cover damages for personal injury or damage caused directly or indirectly in any capacity whatsoever.
7. This warranty terminates when it is found to have been undergoing repairs, alterations or interventions by any person not authorized by Jocel.

THE WARRANTY EXPIRES

1. If the appliance has not been installed by an Accredited Technician.
2. Exceeded the period for home appliances and for industrial appliances, warranty expires and assistance will be made by charging the costs of manpower, according to current fees.
3. With the modification or disappearance of the nameplate of the appliance.

NOTE : GLASSES AND LAMPS ARE NOT COVERED BY WARRANT.

TECHNICAL ASSISTANCE
For technical assistance request, our services are available through the following contacts:
Telef. 00 351 252 910351
Fax: 00 351 252 910367
E-mail: assistencia@jocel.pt
http://www.jocel.pt

Customer Support

HEADQUARTERS:
Rua Alto do Curro, n.º 280
4770-569 S. COSME DO VALE
V.N. de FAMALICÃO
Telef: 252 910 350/2
Fax: 252 910 368/9
email: jocel@jocel.pt
http://www.jocel.pt

References

• JOCEL Electrodomésticos
• JOCEL Electrodomésticos
• JOCEL Electrodomésticos
• JOCEL Electrodomésticos

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>