JOCEL JAT007391 Portable Patio Heater Instruction Manual

JOCEL JAT007391 Portable Patio Heater

SAFETY WARNINGS

1. For use outdoors or in amply ventilated
2. An amply ventilated area must have a minimum of 25% of the surface area
3. The surface area is the sum of the walls
4. This appliance is not fitted with “Atmosphere sensing device”.

• WARNING: The use of this appliance in enclosed areas can be dangerous and is prohibited.
• WARNING: Read the instructions before installation and use.
• WARNING: This appliance must be installed and the gas cylinder stored in accordance with the regulations in force.
• WARNING: Use only the type of gas and the type of cylinder specified in these instructions.
• WARNING: Do not obstruct the ventilation holes of the cylinder housing.
• WARNING: In case of violent wind particular attention must be taken against tilting of the appliance.
• WARNING: Do not move the appliance when in operation.
• WARNING: Shut off the valve at the gas cylinder or the regulator before moving the appliance.
• WARNING: The tubing or the flexible hose must be changed within the prescribed intervals.
• WARNING: Do not connect the gas cylinder directly to the appliance without regulator.

IMPORTANT INFORMATIONS

• LPG cylinder not provided. The appliance is designed to operate with a cylinder size no more than Ø31.8 x 58 cm.
• This appliance requires a 15 kg butane LPG cylinder or a 13 kg propane LPG Gas regulator should be the correct one and be set according to specific gas category (see Technical data on page 3).
• Gas regulator should be approved according to EN 16129:2013 with proper capacity (g/h), pressure, working temperature and inlet + outlet connection for the country of
• The regulator illustrated on the manual is for United Kingdom, the regulator in your country maybe different with the one on the illustration.
• Flexible gas rubber pipe should be approved according to 16436-1:2014 with proper inner Ø to match pipe holders of gas circuit and gas regulator, pressure and working
• The length of the hose is 1.5 m and it should not exceed 1.5 m. The hose shall be readily visible across its entire length for inspection after installation.
• The injector in this appliance is not removable and the injector is only assembled by manufacturer. This appliance is forbidden to convert from one gas pressure to another

DANGER!

You must have the proper regulator and cylinder in order for the appliance to operate safely and efficiently. Use of an incorrect or faulty regulator is dangerous and will invalidate any warranty.

INSTRUCTIONS FOR PLACING AND REMOVING GAS BOTTLE

CONNECT LP GAS CYLINDER

1. Before connecting, be sure that there is no debris caught in the head of the LP tank, head of the regulator valve or in the head of the burner and burner ports.
2. Connect gas line to tank by turning knob clockwise until it stops, make sure that the tube is not subject to twisting.
3. After connecting to gas cylinder, a leak testing is

DISCONNECT LP GAS CYLINDER

1. Before disconnecting make sure the LP gas tank valve in “CLOSED”. Disconnect gas line from LP gas cylinder by turning knob counterclockwise until it is loose.
2. For storage and cylinder exchange, disconnect hose at the cylinder only, DO NOT disconnect hose from appliance.
3. To change the gas cylinder in an amply ventilated area, away from any ignition source (candle, cigarettes, other flame producing appliances…).

LEAKAGE TESTS

Your Outdoor Patio Heater has been checked for leaks at all the factory-made connections. To check the connection of the gas hose/regulator/LPG cylinder.

1. Make leak test solution by mixing 1 part washing up liquid and 3 parts
2. Spoon several drops (or use squirt bottle) of the solution onto the gas hose/regulator and regulator/LPG cylinder connection.
3. Inspect the connections and look for
4. If no bubbles appear, the connection is
5. If bubbles appear, there is leak, loosen and re-tighten this Repeat the test. If bubbles form again, stop trying; contact your local dealer for assistance
6. Leak test annually, and whenever the gas cylinder is removed or replaced.

NOTE : In the event of gas leakage, the appliance must not be used or if already alight, the gas supply must be shut off and the appliance investigated and rectified before it is used again.

DISTANCE FROM SURFACES

This heater is primarily used for the heating of outdoor patios (decks, spas, pools and open working areas).

• Combustible materials are considered to be wood, compressed agglomerates, plant fibers, plastic or other materials that are capable of being ignited and burned.
• Always make sure that adequate fresh air ventilation is provided. Follow the spacing tolerances shown in the following figure right at all times.
• This heater must be placed on level, firm ground.
• Never operate in an explosive atmosphere. Keep away from areas where gasoline or other flammable liquids or vapors are stored or used.

CONNECTING INSTRUCTIONS

1. Turn the control knob to OFF “”
2. Turn LPG cylinder gas valve to fully open
3. Push in gas control knob and turn counter clockwise to MIN ” ” position, this will light the burner. (You will hear 1 clicking noise).
4. Once the burner is lit, continue to keep the control knob depressed for at least 30 seconds, then release the control knob.
5. If burner does not stay lit, repeat steps 3 and 4 after 5
6. If burner still does not stay lit, then:
7. Push in gas control knob and turn counter clockwise to the MIN ” “
8. Keep depressing the control knob, put long stem lighter into the ignition hole on the emitter screen to light the burner.
9. Repeat step
10. Turn control knob counter clockwise to MAX ” ” If you want a lower temperature, push in the control knob and turn clockwise to the MIN ““ position.

WARNING

These lighting instructions must be followed. An unsafe condition can occur if they are not followed correctly.

FLAME CHARACTERISTICS

• The flame pattern at the emitter screen should be visually checked whenever heater is operated. Normally the burner flame is blue, but little yellow flame is acceptable.
• If flames extend beyond surface of the emitter grid, or the phenomena of flame lift or light back, or black soot is accumulating on the emitter grid or reflector, the heater should be turned off immediately. The heater should not be operated again until the unit is serviced and or repaired.

OPERATING INSTRUCTIONS

NOTE: The burner may be noisy when initially turned on, To eliminate excessive noise from the burner, turn the control knob to the MIN “ ” position. Then, turn the knob to the level of heat desired.

WHEN HEATER IS ON:

Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners.

OPERATION PRESSURE CHECKED:

• If the flame is very small, this is because the supply pressure is not enough. Please refill gas cylinder.

RE-LIGHT:

1. Turn the control knob to OFF “●”
2. Wait five (5) minutes before attempting to relight
3. Repeat steps beginning with step 2 of the lighting instruction

SHUT DOWN INSTRUCTIONS:

1. Push in and turn control knob clockwise to OFF “●”
2. Turn LPG cylinder gas valve clockwise to OFF position when heater is not in NOTE: After use, some discoloration of the emitter screen is normal.

THE EVENT OF GAS LEAKAGE:

1. Turn the control knob  to OFF “●”
2. Turn LPG cylinder valve to OFF
3. Wait 5 minutes to allow gas to
4. If odor continues, immediately call gas

Warning:

Heater will be hot after use. Handle with extreme care.

ASSEMBLY INSTRUCTIONS

Number of people required to assemble: One person
Time to assemble: 60 min.

1. Find a large, clean area to assemble your appliance. Please refer to the parts list and assembly diagram as necessary.
2. Please use protective gloves when assembling this
3. To avoid losing any small component or hardware, assemble your product on a hard level surface that does not have cracks or openings.
4. To avoid damage to soft floor or carpet, do not assemble or move the appliance on soft floor or carpet.
5. Follow all steps in order to properly assemble your
6. Make sure all the plastic protection rips off before
7. Do not force parts together as this can result in personal injury or damage to the product. When applicable, tighten all hardware connections by hand first, once the step is completed, go back and full tighten all hardware.

CAUTION: Whilst every effort has made in manufacture of your appliance to remove any sharp edge, you should handle all components with care to avoid accidental injury.

Tools required

COMPONENTS – EXPLODEDVIEW

LIST OF COMPONENTS

ASSEMBLY INSTRUCTIONS

CLEANING AND MAINTENANCE

To enjoy years of excellent heater performance, be sure to perform the following maintenance activities regularly:

• Keep exterior surfaces clean
• Use warm soapy water for Never use flammable or corrosive cleaning products.
• While washing the heater, be sure to keep the area around the burner dry at all
• If the gas control is exposed to water in any way, DO NOT try to use It must be replaced.
• Air circulation must not be Keep controls, burner and circulating air passages clean. Signs of possible blockages include:
• Extreme yellow flame tip and gas
• The appliance does NOT reach the desired
• The glow of the device is excessively
• The appliance makes popping
• Spiders and insects nest in burners or orifices; this dangerous situation can damage the heater and make it unsafe to use. Clean the burner holes using a heavy-duty pipe brush. Compressed air can also help eliminate small particles.
• Carbon deposits can create a fire hazard. Clean the heater dome with warm soapy water if any carbon deposits develop.
• Check the tubing or flexible hose (at least once a month and every time the gas bottle is replaced). If it shows signs of breakage, cracks or other deterioration, it should be replaced with new tubing of the same length and of equivalent quality.

STORAGE

BETWEEN USES:

• Turn the control knob to “●”
• Turn LPG cylinder to OFF
• Store appliance upright in an area sheltered from direct contact with with inclement weather (such as rain, sleet, hail, snow, dust and debris).
• If desired, cover appliance to protect exterior surfaces and to help prevent debris in air passages.

DURING PERIODS OF PROLONGED INACTIVITY OR DURING TRANSPORTATION:

• Turn the control knob to the OFF position (symbol “●”) before covering the
• Unplug the LPG bottle and move it to a safe, well-ventilated location in the open air. DO NOT store in a location exceeding 50°C.
• The LPG bottle must be kept out of reach of children, and never in a building, garage or any other closed area.
• Place the device in an upright position in an area protected from direct contact with meteorological elements (such as rain, hail, snow, dust and debris)
• If desired, cover the appliance to protect the exterior surfaces and help prevent debris depositing in the air passages.

TECHNICAL SPECIFICATIONS ****

COUNTRY| CATEGORY| NOMINAL HEAT INPUT(HS)| GAS CONSUMPTION| INJECTOR DIAMETER(Ø)| GAS & PRESSURE
---|---|---|---|---|---
AT     C

SK

DE

| I3B/P(50)| 8.8 kW| g/h (G30)| 1.3 mm| G30 Butane and G31 Propane at 50mbar
CY     DK    EE| I3B/P(30)| 8.8 kW| g/h (G30)| 1.5 mm| G30 Butane and
FI      FR    HU|  |  |  |  | G31 Propane at
IT      LT     NL|  |  |  |  | 30mbar
NO    SE     SI|  |  |  |  |
SK     RO    HR|  |  |  |  |
TR     BG     IS|  |  |  |  |
LU     MT|  |  |  |  |
BE     CH     CY| I3+(28-30/37)| 8.8 kW| g/h| 1.5 mm| G30  Butane  at
CZ    ES     FR|  |  | (G30) /

g/h

|  | 28-30mbar    and
GB    GR     I E|  |  | (G31)|  | G31 Propane at
IT      L T     LU|  |  |  |  | 37mbar
LV √ PT     SK|  |  |  |  |
SI|  |  |  |  |
PL| I3B/P(37)| 8.8 kW| g/h (G30)| 1.4 mm| G30 Butane and G31 Propane at 37mbar

GENERAL WARRANTY TERMS ****

1. The warranty is valid only on presentation of invoice of
2. This WARRANTY is limited exclusively to parts substitution ineffective due to faulty manufacture, made in our workshops.
3. The elimination of several faults of the scope of the guarantee is made for repair or replacement of defective parts, according to the discretion of our technical Defective parts are our property.
4. Are not covered under warranty damage caused by transportation, neglect or poor use, improper assembly or installation, as well as external influences such as: lightning strikes or power, flooding, humidity, etc.
5. Lose warranty, all appliances that are not being used according to the instructions, or connected to FEEDING NETWORKS not guarantee a constant voltage of 220/240V.
6. The warranty does not cover damages for personal injury or damage caused directly or indirectly in any capacity whatsoever.
7. This warranty terminates when it is found to have been undergoing repairs, alterations or interventions by any person not authorized by Jocel.

THE WARRANTY EXPIRES

1. If the appliance has not been installed by an Accredited
2. Exceeded the period of 2 years for home appliances and 06 months for industrial appliances, warranty expires and assistance will be made by charging the costs of manpower, according to current fees
3. With the modification or disappearance of the nameplate of the

TECHNICAL ASSISTANCE

For technical assistance request, our services are available through the following contacts:
Telef. 00 351 252910351
Fax: 00 351 252910367
E-mail: assistencia@jocel.pt http://www.jocel.pt

HEADQUARTERS:

Rua Alto do Curro, n.º 280 4770-569 S. COSME DO VALE
V.N. de FAMALICÃO Telef: 252 910 350/2 Fax: 252 910 368/9 email: jocel@jocel.pt http://www.jocel.pt

DECLARATION OF CONFORMITY ****

We declare on our own responsibility that the machine indicated below

• Product                                 PATIO HEATER
• Brand                                    JOCEL
• Model                                    JAT007391

Complies with the following European directives and standards implementation
Gas Appliances
(EU) 2016/426
EN 14543:2017
Country of Origin: R.P.C.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>