Pro-Ject T2 W Turntable with WiFi Streamer Instruction Manual
- June 12, 2024
- Pro-Ject
Table of Contents
Pro-Ject T2 W Turntable with WiFi Streamer
Dear Music Lover, Congratulations and thank you for choosing Pro-Ject Audio Systems record player. Your T2 W turntable has been handcrafted and rigorously tested by skilled technicians to give you years of enjoyable, trouble-free service. Please contact your dealer if you require additional assistance.
Important:
Your turntable was shipped partially disassembled in order to avoid damage to
sensitive parts. Please check immediately to make sure that neither the
packaging nor the device was damaged in transit. If you are missing parts or
if the unit is damaged, please do not operate and contact your dealer.
Please do your part to help protect the environment:
Disposal of packaging material: Pro-Ject packaging is carefully designed to protect your component from damage in transit and you are strongly urged to keep the original packaging in order to safely ship or otherwise transport your turntable in the future. However, the packaging materials were chosen to be environmentally friendly, so if you must discard the packaging, please recycle.
GENERAL INFORMATION
Controls, features and connections
- PLATTER & FELT MAT
- CHASSIS
- SPEED CONTROL BUTTON
- MOTOR WITH PULLEY
- DRIVE BELT
- SUB-PLATTER
- TONEARM COUNTERWEIGHT
- ANTI-SKATING ADJUSTMENT SCREW WITH SCALE
- TONEARM REST / REMOVABLE TRANSPORT LOCK
- TONEARM LIFT LEVER
- TONEARM TUBE
- HEADSHELL WITH FINGER LIFT AND PRE-MOUNTED CARTRIDGE
- LID
- LID HINGES
- HINGE FASTENERS
- POWER SUPPLY SOCKET
- LINE RCA OUT, ETHERNET, Wi-Fi RESET SWITCH, Wi-Fi ON/OFF BUTTON, Wi-Fi STATUS LED
Accessories
- SINGLE ADAPTOR
- ALLEN KEY 1,5mm
- COUNTERWEIGHT no. 105 (FOR CARTRIDGE WEIGHT 5 – 11.5g)
- TWO-POINT CARTRIDGE ALIGNMENT PROTRACTOR
- CONNECTION CABLE (CONNECT IT E RCA)
- SETUP GUIDE
- UNIVERSAL POWER SUPPLY
SETUP
Platter and drive belt installation
Please remove drive belt from accessories box and install it as shown in the
following illustration. Put the felt mat on the top of the platter
Cartridge installation, stylus exchange
- If you purchased this turntable in a package that included the cartridge, this has already been done for you. Install the cartridge into the aluminium headshell, using the appropriate hardware included with your cartridge. All cartridges with half inch mounting holes can be fitted.
Connect the cartridge as indicated below:
- White left channel L+
- Red right channel R+
- Green right channel R-
- Blue left channel L-
For correct cartridge alignment, use the two-point cartridge alignment protractor provided with your T1 accessories. If unfamiliar with two-point setup, please refer to your dealer. A damaged or worn stylus may harm your record collection and should be replaced. Please remove stylus protection before pulling the stylus from the cartridge and replace for a new one. Stylus type is exchange for pre-mounted cartridge Sumiko Rainier: Stylus Sumiko Rainier. If in doubt, consult your local dealer or distributor.
Vertical Tracking Force setting (VTF)
The T2 W comes with the counterweight already assembled on the tonearm, and
the tracking force is factory pre-adjusted. To adjust or fine tune the
tracking force manually, loosen the hexagonal screw on top of the
counterweight (6) using the allen key provided. Remove the stylus protection
cover and place the stylus pressure gauge onto the platter. To set the
required VTF, lower the tonearm lift lever (10) as indicated in the
illustration and place the tip of the stylus on one of the points on the
scale. For example, the Sumiko Rainier requires 20mN of tracking force, so
place the stylus on the 20mN point. If the stylus gauge becomes level when the
tonearm is lowered down onto the desired point, then the correct pressure has
been achieved. However, if there is insufficient or excessive pressure, the
gauge will either not move or tilt down.
To adjust the amount of pressure, carefully move the counterweight (11) along
the support rod, until the stylus pressure is sufficient to raise the pressure
gauge to the level position. Moving the counterweight (6) away from the
cartridge will reduce pressure and towards will increase pressure. Finally
secure the counterweight (6) using hexagonal key provided. 
Maintenance and cleaning
Your record player requires little or no regular maintenance. Remove dust with
a slightly moistened antistatic cloth. Never use a dry cloth because this will
create static electricity which attract more dust! Antistatic cleaning fluids
are available at specialist stores but must be applied sparingly to avoid
damage to rubber parts. It is recommended to fit the needle cover before
cleaning or maintenance is carried out to avoid damage. If the player is not
used over a long period of time the drive belt can be removed to prevent
unequal stretching.
Switching on and off, changing replay speed
The turntable is equipped with a three-position switch for ON/OFF and
electronic speed change. To play records at 33 rpm. press this switch (3) to
the rear side. To play records at 45 rpm. press this switch (3) to the front
side as shown on illustration below.
Anti-skating
The anti-skating force is pre-adjusted from the factory corresponding to the
tracking force. Sumiko Rainier recommended tracking force 20mN = anti-skating
set to 2 (middle position). You can adjust the anti-skating by rotating the
anti-skating setting screw to the left or right.
Connection to the amplifier
The record player has gold plated female RCA phono sockets with LINE output
(the internal phono preamp of the T2W is always on). Connect the RCA outputs
of your T2 W to a line input (such as AUX, CD, Tuner, Tape or Video) on your
amplifier. Take care to connect the left and right channels correctly. The
right channel is usually marked red, the left channel black or white. The
earthing wire of the tonearm lead should be connected to the earth terminal on
your amplifier (if provided). The analogue RCA output remains purely analogue
and is not digitized, not affected by any additional delay or in any other way
influenced by the Wi-Fi capabilities of the turntable. You can rest assured
that the analogue output will always give you the pure analogue output signal.
Wi-Fi
App Control: Please download the App “Pro-Ject Control” (Android and iOS) to control the Wi-Fi functionalities of your T2 W. Browser Control: You can enter die IP address of your T2 W into any webbrowser on a device connected to the same network andcontrol the Wi-Fi functionalities of your T2 W in exactly the same way as with the App. You can use IP Scanners or get the IP address from the “Pro-Ject Control” App. Alternatively, the Pro-Ject Control App will show you the IP address of your turntable as well, after you connected it to your network via ethernet or Wi-Fi.
Wi-Fi Startup
The Wi-Fi module of your T2 W will boot up as soon as you connect the power
supply to your turntable.
You can see its status from the colour of the LED:
- Red static: Wi-Fi module starting up
- Red blinking: Module started up, no ethernet or Wi-Fi connection established
- Green static: Connected to ethernet or Wi-Fi network
- Blue static: Streaming audio
- Blue blinking: Previous streaming receiver unavailable
Network Connection
Ethernet: Connect an ethernet cable, the network connection will be
automatically established and LED turns green. Ethernet is recommended for
lossless streaming (note that also your streaming receiver should be connected
via ethernet and not Wi-Fi to avoid connectivity issues). Wi-Fi: You can add
the T2 W to your Wi-Fi network via our “Pro-Ject Control” App. Connect your T2
W to power and wait until Wi-Fi module has finished booting (Status LED). Then
open the “Pro-Ject Control” App and you will see your turntable in the list of
devices waiting to be connected to a Wi-Fi network. If the turntable and the
Wi-Fi Setup don’t show up immediately, don’t worry. It can take 10 seconds to
scan for available devices. Press “Wi-Fi Setup” and follow the next steps.
Wi-Fi setup is done via BLE (= Bluetooth Low Energy), so please make sure your phone is granting Bluetooth access to the “Pro-Ject Control” App. For BLE, you do not need to pair your phone to the turntable. BLE always, doesn’t matter which BLE device, works WITHOUT pairing. A low energy Bluetooth connection can be established on the fly automatically, just by having Bluetooth turned on and access granted to the App. Please allow 10-15 seconds for your phone to discover the turntable after first starting the app, depending on how fast the Bluetooth connection is. If necessary, restart your phone after granting access.
Wi-Fi Control Button
Press for 2 seconds: Turns Wi-Fi on or off Short press: When turned on, start
streaming to the previously selected streaming device The Wi-Fi Control Button
is a quick interface for you to start streaming to the streamer that you
previously selected in the Pro-Ject Control App or T2 W webinterface. You can
also turn off the Wi-Fi module should you wish to declutter your Wi-Fi
network. Energy consumption is negligible in idle mode when the module is
turned on. But it won’t hurt to turn the module off, if you don’t use your
turntable for longer periods to save energy consumption. In usual operation
you will probably not need this button, as you will choose which device to
stream to in your App or webinterface. But once you have chosen an output
streamer once, you can comfortably start streaming to it again in a later
session, by just pressing the button once. This saves time and there is no
need to break out the App or webinterface.
Pro-Ject Control App & Webinterface
With the Pro-Ject Control App or the T2 W’s webinterface you’ll do most of
your interaction with the T2 W.
After connecting the T2 W to your network, choose which device to control (should you have more than one on your network) from the main screen and from there choose which output device you want stream your turntable to. You can stream to as many output devices as your network connection can handle. To stop the stream simply select the output device again, the blue outline will go away, and streaming to that device will stop. Allow some time after choosing an output device and sending the stream to them. Each device reacts differently past and reports the status back. Some are almost instantaneous and some take a few seconds. The T2 W uses UPNP to hand over the digital audio streams and the streams itself are either MP3 or FLAC, and implementations can vary from manufacturer to manufacturer.
The more output devices you stream to, the more network bandwidth you need. The T2 W has very powerful Wi-Fi and ethernet and internal processing power and can in theory handle hundreds of lossless audio streams at the same time. The bottleneck is most likely your Wi-Fi access point or Wi-Fi pollution (too many different Wi-Fi networks in too close proximity to each other.
Options Menu
- The wheel in the top left corner takes you to the options menu.
- Automatically starts streaming to the last selected output device as soon as the motor of the T2 W is turned ON.
- Enter Wi-Fi connection data or configure Ethernet
- Displays network information
- Check back here regularly for Firmware Updates
- Settings for language, power management and factory reset
- Advanced streaming settings
Streaming Compatibility
The standard audio stream is designed to be compatible with as many devices as
possible. Requirements are that your streamer is UPNP capable and can play MP3
encoded live-streams. An up-to-date list of compatible manufacturers and
devices can be found on the T2 W product page on our Pro-Ject Audio Systems
website.
Lossless Audio Stream
The lossless audio stream in the Advanced Settings is not intended to be
compatible with as many devices as possible, but is intended to be used with
high-end streamers like our own Stream Box S2 Ultra in excellent network
conditions. Please make sure to use this setting only on really good W-Fi
connections or with ethernet cables, as lossless requires roughly 6x more
bandwidth At Pro-Ject Audio Systems the Stream Box $2 Ultra and Stream Box $2
are compatible with the lossless stream. A list of lossless compatible
devices/manufacturers can be found on the T2 W product page on our ProJect
Audio Systems website. If the lossless audio stream is turned on, only
selected compatible devices will receive it, the rest will continue to receive
the standard compressed stream, so you won’t run into any major bugs or
issues.
Secondary Stream
The secondary stream in the Advanced Settings is a nice helper, in case your
streaming device is not UPNP capable. Many streamers allow adding custom radio
stations. If you start the secondary stream and copy the stream-link into your
webbrowser or add a custom radio station, you’ll get to enjoy your T2 W on
many more devices.
The secondary stream is only available as MP3.
Airplay
While the T2 W is not able to play to Airplay devices directly, you can build
a workaround with the secondary stream.
Long press on the stream link -> Open Link -> Press Airplay symbol -> Choose which device to play to
Network Standby
By default, your T2 W is configured to enter network standby after 20 minutes
of inactivity. You can disable this functionality at your choice under Device
Settings -> Power Management -> Auto Standby Mode.
If the T2 W is greyed out like here, it means it is currently in Network Standby mode. You can wake it up with the power button. You can also manually set it to network standby mode using the power button on the home screen.
Technical specifications ProJect T2 / Pro-Ject 9″
- Nominal speeds 33/45 .p.m.
- Speed variance 33: =0.60% 45: =0.50%
- Wow and flutter 33: =0.19% 45: ‡0.17%
- Signal to noise -67dB
- Effective tonearm mass 9.5g
- Effective tonearm length 9″ (230mm)
- Overhang 22 mm
- WLAN standards IEEE 802.11a/b/g/n/ac/ax 2×2 MIMO; 2.4/5GHz
- Power consumption 4.5W
- Power input 15V/ 0.8 A DC, universal power supply
- Dimensions (W × H x D) 457 × 134 × 335mm
- Weight 5.5kg
- Dimensions packaging (W × H x D) 542 × 300 × 412mm
- Weight incl. packaging 8.5kg
Technical specifications MM-Cartridge Sumiko Rainier
- Frequency range 15-25.000Hz
- Channel separation 25dB/1kHz
- Output voltage 5mV
- Recommended load impedance 47 kohms/ amplifier connection – MM-input
- Compliance/stylus type 10×10-6cm/dyn @ 100Hz- elliptical
- Recommended tracking force 20 mN
- Capacitance 100pF – 200pF
- Weight 6.5g
Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo
strict quality controls before leaving the factory. Faults that may possibly
occur are not necessarily due to material or production faults but can
sometimes be caused by incorrect use or unfortunate circumstances. Therefore,
the following list of common fault symptoms is included.
The platter doesn’t turn although the unit is switched on:
- The unit is not connected to the mains power supply.
- No mains at the socket.
- Drive belt is not fitted or has slipped off.
No signal through one or other channel or both channels:
No signal contact from the cartridge to the internal tonearm wiring or from
that to the arm lead or from that to the phono box or between that and the
amplifier. This could be due to a faulty plug, broken wire or solder joint or
simply loose plug/socket connection. Correct input not selected at amplifier.
Amplifier is not switched on. Amplifier or speakers are defective or muted. No
connection to the loudspeakers.
Distorted or inconsistent sound from one or both channels:
Record player is connected to wrong input of amplifier. Needle or cantilever
damaged. Wrong r.p.m., drive belt overstretched or dirty, platter bearing
without oil, dirty or damaged
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country. Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason, we recommend keeping the original packaging. Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt. Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering
to these instructions for use and/or by transportation without the original
packaging. Modification or change to any part of the product by unauthorized
persons, release the manufacturer from any liability over and above
the lawful rights of the customer.
- Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger. This guide was produced by: Pro-Ject Audio Systems Copyright © 2023. All rights reserved.
- The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.
- Mac®, Mac OS®, iOS, Airplay, Apple are trademarks of Apple Inc., registered in the U.S. and other countries. Android™ is a trademark of Google Inc.
FCC STATEMENT
Waste from Electrical and Electronic Equipment (WEEE): This directive mandates the collection and recycling of electronics and component materials in order to reduce the amount going to landfills. Outside North America, when the user decides to discard this product, it must be sent to a separate collection facility for recycling. Please contact your point of purchase for more details. Federal Communication Commission (FCC) Interference Statement FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC´s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Contains FCC ID: 2AJYB-S1955
Declaration of Conformity
We, SEV Litovel, s r.o. Palackého 1160/34 78401 Litovel Czech Republic (manufacturer) and Pro-Ject Audio Systems a division of Audio Tuning GmbH Margaretenstrasse 98 1050 Vienna, Austria (distributor) declare under our responsibility that the product is in conformity with the provisions of Directives:
- 2014/35/EU including amendments
- 2014/30/EU including amendments
- 2014/53/EU including amendments
The following harmonised standards were applied: Health: EN62479:2010Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013, EN62368-1:2014/A11:2017, EN61558-1:2005/A1:2009, EN61558-2-16:2009/A1:2013 EMC: EN301489-1 V2.2.0: 2017-03, EN301489-17 V3.2.0:2017-03, EN55032:2015, EN55035:2017, EN61000-3-2:2014, EN61000-3-3:2013 Radio Spectrum: EN300328 V2.1.1 (2016-11) Pro-Ject Audio Systems a division of Audio Tuning GmbH 1050 Vienna, Austria, Margaretenstrasse 98 info@project-audio.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>