PHILIPS TAUN102 r Bluetooth in-ear headphones User Manual

PHILIPS TAUN102 r Bluetooth in-ear headphones

Introduction

The PHILIPS TAUN102 Bluetooth in-ear headphones offer a sleek and wireless listening experience designed for those constantly on the move. Leveraging Bluetooth connectivity, these in-ear headphones provide effortless pairing with various devices, allowing users to enjoy music, podcasts, or calls without the hindrance of wires. Compact and ergonomic, the TAUN102 model showcases Philips’ commitment to quality audio and modern convenience. Perfect for commutes, workouts, or relaxed listening, the PHILIPS TAUN102 is an ideal choice for contemporary, wireless audio enjoyment.

Important safety instructions

Hearing Safety

Danger: To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Be sure to observe the following guidelines when using your headset.

• Listen at reasonable volumes for reason-able periods of time.
• Be careful not to adjust the volume continuously upwards as your hearing adapts.
• Do not turn up the volume so high that you can’t hear what’s around you.
• You should use caution or temporarily discontinue use in potentially hazardous situations.
• Excessive sound pressure from earphones and headphones can cause hearing loss.
• Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.
• For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

General information

To avoid damage or malfunction:

Caution

• Do not expose headphones to excessive heat
• Do not drop your headphones.
• Headphones shall not be exposed to dripping or splashing.
• Do not allow your headphones to be submerged in water.
• Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
• If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
• The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

About operating and storage temperatures and humidity

• Operate or store in a place where temperature is between -15°C (5°F) and 55°C (131 °F) (up to 90% relative humidity.
• Battery life may be shorter in high or low temperature conditions.

Product Introduction

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome

With this Philips wireless in-ear headphones, you can:

• enjoy convenient wireless handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.

What’s in the box

• Philips Bluetooth in-ear headphones TAUN102
• Earfins
• Caps
• USB charging cable (for charging only)
• Quick start guide
  

Product Overview

1.  Next / Volume up
2. MIC / LED indicator
3. On/off, music/call control button
4. Micro USB charging slot
5. Previous/Volume down

Get started

Charge your headphones

Note

• Before you use your headphones for the first time, charge the battery for 5 hours for optimum battery capacity and lifetime.
• Use only the original USB charging cable to avoid any damage.
• Finish your call before charging the headphones, as connecting the headphones for charging will power the headphones off.

Connect the supplied USB charging cable to:

• the micro USB charging slot on the headphones and;
• the charger/USB port of a computer LED turns red during charging and turns blue when the headphones is fully charged.

Tip: Normally, a full charge takes 2 hours.

Pair the headphones with your mobile phone

Before you use the headphones with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and mobile phone. The headphones store the last 8 devices in the memory . If you try to pair more than 8 devices , the earliest pained device is replaced by the new one.

1. Make sure that the headphones are fully charged and turned off.
2. Press and hold the on/off button, blue and red LED flashes alternately. Blue light flashes for successful pairing.
   • The headphones remain in pairing mode for 5 minutes.
3. Make sure that the mobile phone is turned on and its Bluetooth feature is activated.
4. Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone.

The following example shows you how to pair the headphones with your mobile phone.

1. Activate the Bluetooth feature of your mobile phone, select Philips UN102.
2. Enter the headset password “0000” (4 zeros) if prompted. For those mobile phones featuring Bluetooth 3.0 or higher, no need to enter a password.

Use your headphones

Connect the headphones to a Bluetooth device

1. Turn on your mobile phone/Bluetooth device.
2. Press and hold the on/off button to turn the headphones on.
   • The blue LED flashes.
   • The headphones are reconnected to the last connected mobile phone/ Bluetooth device automatically. If the last one is not available, the headphones try to reconnect to the second last connected device.

Tip: If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone/Bluetooth device manually.

Note: If the headphones fail to connect to any Bluetooth device within range in 5 minutes, it will switch off automatically to save the battery life.

Manage your calls and music

On/off

Music control

Call control

Other headphones indicator status

Technical data

• Music time: 7 hours
• Talk time: 6 hours
• Standby time: 150 hours
• Normal time for a full charge: 2 hours
• Rechargeable lithium polymer battery (80 mAh)
• Bluetooth 5.0 Bluetooth mono support (Headset Profile – HSP, Hands-Free Profile – HFP), Bluetooth stereo supported (Advanced Audio Distribution Profile – A2DP; Audio Video Remote Control Profile-AVRCP)
• Operating range: Up to 10 meters (33 feet)
• Digital echo & noise reduction
• Auto power off

Note: Specifications are subject to change without notice.

Notice

Notice of compliance

Notice for US

The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate the receiving antenna.
• Increase the separation between equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Notice for Canada:

• CAN ICES-3(B)/NMB-3(B)

This device contains licence-exempt transmit-ter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Declaration of conformity

Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com.

Disposal of your old product and battery

This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com.

This product contains non-removable batteries:

• Do not incinerate. Batteries may explode if overheated.
• For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com.

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol on a product means that the product is covered by European Directive 2012/19/EU.

This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery.

Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery

Note: Make sure the headphones are disconnected from the USB charging cable before removing the battery.

If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.

Compliance with EMF

This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

Environmental information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Trademarks

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

Customers’ Support

• Register your product and get support at www.philips.com/support

FAQs

My Bluetooth headphones do not switch on.

The battery level is low. Charge the headphones.

I cannot pair my Bluetooth headphones with a mobile phone.

The Bluetooth is disabled. Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headphones.

Pairing does not work.

Make sure the headphones are in pairing mode. Make sure that the LED light flashes blue and red alternately before you release the call/music button. Do not stop holding the button if you see the blue LED only.

The mobile phone cannot find the headphones.

The headphones may be connected to a previously paired device. Turn off the connected device or move it out of range. Pairing may have been reset or the headphones have been previously paired with another device. Pair the headphones with the mobile phone again as described in the user manual.

The audio quality is poor and crackling noise can be heard.

The Bluetooth device is out of range. Reduce the distance between your headphones and Bluetooth device, or remove obstacles between them.

The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.

Make sure your mobile phone not only supports (mono) HSP/HFP but also supports A2DP

I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/ backward).

Make sure the Bluetooth audio source supports AVRCP

What is the battery life of the PHILIPS TAUN102 in-ear headphones?

The PHILIPS TAUN102 offers up to 7 hours of wireless music enjoyment on a full charge.

Does the PHILIPS TAUN102 feature any fast-charging technology?

Yes, the headphones come with FAST CHARGE technology, allowing 90 minutes of playback with just a 15-minute charge.

How can I store the PHILIPS TAUN102 when not in use?

The headphones have MAGNETIC FLUETED earbuds that snap together, ensuring neat and easy storage when not in use.

Can I make calls with the PHILIPS TAUN102?

Yes, these headphones come with a built-in microphone, allowing you to make clear calls.

Is there a way to control the volume on the PHILIPS TAUN102?

Yes, the headphones include a built-in control feature for convenient volume adjustment.

Download this PDF Link: PHILIPS TAUN102 r Bluetooth in-ear headphones User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>