TYPE S ML-533067_V1 LED Sport Brake Light User Manual

TYPE S ML-533067_V1 LED Sport Brake Light

Product Information

• Product Name: LED Sport Brake Light
• Model Number: ML-533067
• Operating Voltage: DC 12V System Only
• Power Consumption: 1.9W
• LED Type: 2835 Red LED
• LED Color: Red
• Maximum Amperage Draw: 0.165A
• Water Resistance: IP65 Rating

Package Contents

• 1 X LED Sport Brake Light
• 2 X 20mm M5 Screws
• 2 X 10mm M5 Screws
• 1 X Mounting Bracket
• 4 X M5 Nuts
• 1 X Warranty Card
• 1 X Instruction Manual
• 4 X M5 Spring Washers
• 4 X M5 Washers

Installation Tools Needed (Not Included)

• Power Drill
• Philips Head Screwdriver
• Wrench
• 5.5mm (13/64 inch) Drill Bit

Warnings and Important Safety Instructions WARNING: Do not install or use the product if it impairs the safe operation of your vehicle. Follow the manufacturer’s instructions for proper and safe installation. Neither the manufacturer nor the reseller can be held responsible or liable for any damages to person or property resulting from improper installation or use of this product. Check your state or provincial laws before installing.
This product is not DOT approved and is designed for intended use only. It is not suitable for use in extreme temperatures such as under hood applications. The product is intended solely for decorative purposes. Check local laws and regulations regarding installation and use. The manufacturer and seller assume no liability for improper installation or use, which are solely the responsibility of the purchaser.

Product Usage Instructions

Installation Type 1

1. Choose a suitable mounting location alongside the bumper.
2. Mark 3 holes for a precise installation, ensuring that the surface is strong enough for mounting and nothing behind it will be damaged by drilling.
3. Drill 2 pilot holes for the studs with a 5.5mm (13/64 inch) Drill Bit. Drill one more hole big enough for the power cable to pass through.
4. Line up the Sport Brake Light with the pilot holes and secure the top two studs with M5 Nut, Washer, and Spring Washer using a wrench.

Installation Type 2

1. Mark 2 holes at the bottom of your bumper for a precise installation, ensuring that the surface is strong enough for mounting and nothing behind it will be damaged by drilling.
2. Drill 2 pilot holes with a 5.5mm (13/64 inch) Drill Bit.
3. Install the Mounting Plate with two 20mm M5 screws, Nuts, Washers, and Spring Washers. Tighten using a screwdriver and a wrench.
4. Install the Sport Brake Light to the Mounting Plate and secure with two 10mm M5 screws, Nuts, Washers, and Spring Washers. Tighten using a screwdriver and a wrench.

Power Connection

1. Turn off your vehicle’s engine.
2. Connect the hardwire cables to the vehicle’s power source according to the following graph:

Note: Every installation is unique, and we provide simple installation information, but professional installation is highly recommended.

PACKAGE CONTENTS

SPECIFICATIONS

INSTALLATION

TOOLS NEEDED (NOT INCLUDED)

Installation Type 1

(Follow these steps to mount the Sport Brake Light)

1. Choose a suitable mounting location alongside the bumper.
2. Mark 3 holes for a precise installation and make sure the surface is strong enough for mounting, and nothing behind it will be damaged by drilling.
3. Drill 2 pilot holes for the studs with a 5.5mm (13/64 inch) Drill Bit. Drill one more hole big enough for the power cable to pass through.
4. Line up the Sport Brake Light with the pilot holes and secure the top two studs with M5 Nut, Washer and Spring Washer with a wrench.

Installation Type 2

(Follow these steps to mount the Sport Brake Light to the bottom of the bumper)

1. Mark 2 holes at the bottom of your bumper for a precise installation and make sure the surface is strong enough for mounting, and nothing behind it will be damaged by drilling.
2. Drill 2 pilot holes with a 5.5mm (13/64inch) Drill Bit.
3. Install the Mounting Plate with two 20mm M5 screws, Nuts, Washers and Spring Washers and tighten with screwdriver and a wrench.
4. Install the Sport Brake Light to the Mounting Plate and secure with two 10mm M5 screws, Nuts, Washers and Spring Washers and tighten with screwdriver and a wrench.

Installation Type 2 – Done

NOTE: Every install is unique and we provide simple installation information but professional installation is highly recommended.

POWER

1. Turn off your vehicle’s engine.
2. Connect the hardwire cables to the vehicle’s power source according to the graph below.

WARNING

IMPORTANT SAFETY INSTRUCTIONS

1. SAVE THESE INSTRUCTIONS– This manual contains important safety and operating instructions.
2. Before using this product, read all instructions and cautionary markings.
3. Use of an attachment not recommended or sold by the manufacturer may result in a risk of fire, electric shock, or injury to persons.
4. Do not operate with damaged Sport Brake Light replace it immediately.
5. Do not operate the Sport Brake Light if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceperson.
6. Do not disassemble the Sport Brake Light; take it to a qualified serviceperson when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
7. To reduce risk of electric shock, disconnect the Sport Brake Light from the car battery before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.

WARNING: do not install or use product if it, in any way, impairs the safe operation of your vehicle. Follow manufacturer’s instructions to ensure the product is properly & safely installed. Neither the manufacturer nor the reseller can be held responsible or liable for consequential, incidental, or indirect damages to either person or property resulting from the installation or improper use of this product. Check your state or provincial laws before installing.

• This product is not DOT approved and is designed for intended use only. Not for use in extreme temperature such as under hood applications.
• This product is intended solely for decorative purposes. Check local laws and regulations regarding installation and use. Manufacturer and seller assume no liability for improper installation or use, which are solely the responsibility of the purchaser.
• WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate
  (DEHP) and Diisononyl phthalate (DINP), which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Model: LM533067

• A Horizon Brands Company
• 2975 Red Hill Ave., Ste. 100,
• Costa Mesa, CA 92626, U.S.A. 1.866.294.9244 info@typesauto.com © 2022 TYPE S. All rights reserved. www.typesauto.com

Documents / Resources

| TYPE S ML-533067_V1 LED Sport Brake Light [pdf] User Manual
ML-533067_V1, LM533067, ML-533067_V1 LED Sport Brake Light, LED Sport Brake Light, Sport Brake Light, Brake Light, Light, ML-533067DNR_V1
---|---

References

• P65Warnings.ca.gov
• TYPE S Auto

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>