ArduCam B024001 12MP IMX477 HQ Camera Board with Tripod Mount for Raspberry Pi User Guide
- June 4, 2024
- ArduCam
Table of Contents
ArduCam B024001 12MP IMX477 HQ Camera Board with Tripod Mount for
Raspberry Pi
This Arducam IMX477 High-Quality Camera board is designed for Raspberry Pi, no lens is included in this product, and we recommend you use a C- or CS-mount lens with it.
SETUP
Fitting the lens
-
Identify your lens mount Type
You should prepare a lens for this camera board. 3 kinds of lenses are used most for embedded cameras – M12 lens, C-Mount Lens, and CS-Mount Lens. Make sure which kind of lens you are using before proceeding. -
For CS-Mount Lens
CS-mount is the stock mount of this camera module, and it won’t focus properly if any other adapter is fitted, so remove it if there is one. Then rotate the CS-Mount lens into the CS camera mount. -
For C-Mount Lens
Thread the C-CS adapter that comes with the lens first. C-mount lens has a longer back focus length, and therefore requires the adapter. Then rotate the C-Mount Lens into the C-CS adapter. -
For M12 Lens
Thread the M12-CS adapter that comes with the lens first. Then rotate the M12 Lens into the M12-CS adapter.
CONNECT THE CAMERA
You need to connect the camera module to the Raspberry Pi’s camera port.
- Locate the camera port near the USB C power connector, and gently pull up on the plastic edge.
- Push in the camera ribbon and make sure the silver connector is facing the Raspberry Pi camera MIPI port. Do not bend the flex cable and make sure it is firmly inserted.
- Push the plastic connector down while holding the flex cable until the connector is back in place.
SPECS
-
Size: 38 x 38 x 18.4mm (excluding lens)
-
Still resolution: 12.3 Megapixels
-
Video modes: Video modes: 1080p30, 720p60
and 640 × 480p60/90 -
Linux integration: V4L2 driver available
-
Sensor: Sony IMX477
-
Sensor resolution: 4056 x 3040 pixels
-
Sensor image area: 6.287mm x 4.712 mm (7.9mm diagonal)
-
Pixel size: 1.55 µm x 1.55 µm
-
IR Sensitivity: Visible light Interface: 2-lane MIPI CSI-2
-
Default Lens Mount: CS-Mount
-
Hole Pitch: Compatible with 29mm, 30mm, 34mm
SOFTWARE SETTING
Please make sure you are running the latest version of Raspberry Pi OS. (January 28th 2022 or later releases, Debian version: 11 (bullseye)). For Raspbian Bullseye users, please do the following
- Edit the configuration file: sudo nano /boot/config.txt
- Find the line: camera_auto_detect=1, update it to: camera_auto_detect=0 dtoverlay=imx477
- Save and reboot
For Bullseye users running on Pi 0-3, please also:
Open a terminal
- Run sudo raspi-config
- Navigate to Advanced Options
- Enable Glamor graphic acceleration
- Reboot your Pi
OPERATING THE CAMERA
For Raspbian Bullseye users, please do the following: For Bullseye users
running on Pi 0-3, please also: Please make sure you are running the latest
version of Raspberry Pi OS. (January 28th 2022 or later releases, Debian
version: 11 (bullseye)). https://www.arducam.com/docs/cameras-for-raspber ry-
pi/raspberry-pi-libcamera-guide/ Specifications are subject to change without
notice. No part of the specifications may be reproduced in any form or by any
means or used to make any derivative such as translation, transformation, or
adaptation without permission from Arducam. All
rights reserved.
CONTACT US
Email: support@arducam.com
Forum: https://www.arducam.com/forums/
Skype: arducam
libcamera-still is an advanced
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>