ZGCINE ZG-R30 Charging Case for Rode Wireless GO & Wireless GO II User Manual

User Manual

Description

ZG-R30 is a charging case which is designed for the RODE Wireless Go microphone, which has soft contours and neat exterior design with over-current protection, over-voltage protection, over-temperature protection, and abnormal detection functions that can prevent battery damage due to over-charge; Charging Case adopts flame retardant material to ensure safe charging of equipment.

Introduction

Product Technical Parameters

Model| ZG-R30| Type| Charging Case for
Rode Wireless Go Series
---|---|---|---
USB-C Input| 5Vm2.4A 9Vm2A 12V.+ 11.5A(MAX)| Battery Capacity| 3.7V 3400mah
USB-C Output| TYPE-C’3 500ma(MAX)| USB-A Output| 5V =2.4A
Dimension| 135mm73mm66mm| Body Material| ABS
Operate Temperature| -20°C-+55t| Weight| 230g
Fully
Recharge Time| About 2 hours
Applicable| Rode Wireless Go Series Microphone

Feature

1. Compact design makes it easy to carry around.
2. Intelligent control of the charging process, to prevent over-charge, over-voltage, over-temperature, over-current, fast and stable, safe and reliable;
3. the accurate slot makes the charging products are easy to install, and would not fall off when shaking lightly.
4. You can observe the battery capacity through the indicator light, easy to grasp the charging state;
5. Equipped with three charging slots, you can charge 1-3 products at will, fast charging to save your time and prevent the battery over-charge.
6. Support the use of multiple devices at the same time,s up port charging and discharging at the same time, large capacity, long-lasting battery life; .Fire retardant materials adapt to the complex outdoor charging environment.

Function

Built-in safety integrated circuit, with strong multiple protection functions, compatible with the original and brand batteries

| Temperature protection thermistor and temperature control processing mechanisms are added to ensure the lithium battery works in a safe temperature range.
---|---
| Overvoltage protection the OVP circuit design makes sure to prevent the over-high input voltage, to avoid damage to the back-end circuit.
| Output anti-reverse protection if the installation is wrong, it will automatically interrupt the work to protect the charging equipment.
| Battery overcharge protection adds lithium battery protection device, effectively avoid the battery overcharge and over•discharge, prevent damage to the battery.
| Short circuit protection adds fuse device, trigger automatic protection in case of abnormal short circuit, to avoid the damage of motherboard and battery.
| Output overcurrent protection intelligent detection of output current, when the output current exceeds the limit, the output circuit would be shut down automatically to protect the charging device.
| Output overvoltage protection intelligent real-time detection of output voltage, when the output voltage exceeds the upper limit, it will automatically close the output circuit to protect the charging device.
| Plug and Play Ready to use immediately when you connect it to the charging device.

Operation Guide

Battery Status: Press the button to check the remaining battery. Each white light blinks represent 25% percent of the remaining battery.
Working Status: Solid white light always displays when the device is working.
Standby Mode: If no operation within 30 seconds, the light will tum off automatically.
Quick standby Mode: Double dick the button, the light will be turned off.

Storage and Transportation

1. If the charging case is not used for a long time, please charge it to a half-full state, place it in a dry and ventilated place, and check per six months.
2. The charging case should be stored in a clean, dry, and ventilated environment, avoid contact away from fire and heat sources.
3. Store temperature:5C-+35¢ Relative humidity759% RH
4. The charging case should be packed into cartons for transportation.
   During transportation, it should prevent violent vibration, impact, or extrusion, and prevent sun and rain. It can be transported by vehicles, trains, ships, planes, and other means of transportation.

Packing list

Maintenance and after-sales service

1. One year warranty
   The damage due to failure to operate in accordance with the instructions and precautions will not be covered by the warranty.

2. Warranty period
   Warranty period: the warranty period of the product is calculated from the date you purchase the product. The warranty card is a valid warranty certificate.

3. Warranty Limitation
   For the following cases of product failure, the company will not provide the warranty service as promised:

• Products and components do not belong to our company.
• Out of warranty.
• Fault caused by the transfer wiring or mobile power which are not provided by our company.
• Force majeure factors, such as earthquake, fire, and other natural disasters or accidents.
• Aging or damage of components.
• Product failure is caused by self-disassembly, repair, or drop.
• Damage caused by incorrect voltage selection.
• Damage due to improper use.

Maintenance record card

• This warranty card will not be reissued after loss, please keep it properly.
• This product has passed strict inspection, In case of any problem, please contact the company’s after-sales service department or the dealer.
  Prohibit self-disassembly.

Shenzhen Zhengguang imaging Equipment Co., Ltd.
Add;5th Floor,1st Building, Aiaao Industrial Park, Shenzhen, Guangdong, China
Postcode: 518000
Tel0755-2941 5015
Web:wwww.zgcine.com
Email:[email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>