Hotpoint AH12E15D3B PTAC with Electric Heat Installation Guide

Hotpoint AH12E15D3B PTAC with Electric Heat

Product Information

• Model: AH12E15D3B
• Product Type: Electric Heater
• Voltage: 230/208 Volt
• Heater Watts: 3,500 / 2,897
• Heater BTU: 10,900 / 8,900
• Heater Amps: 15.3 / 13.7
• Minimum Circuit Requirement: 20 Amps
• Recommended Protective Device: 20 Amp Time-Delay Fuse or Breaker

Product Usage Instructions

1. Measure the wall opening dimensions for installation.
2. Add 1/4 inch to the A and C dimensions for all cut-outs.
3. Ensure the wall case dimensions fit the opening dimensions.
4. The RAB80 model requires a minimum height of 16-1/4 inches and a minimum width of 42-1/4 inches.
5. Connect the electric heater using the provided line cord.
6. Ensure the voltage matches the product specifications (230/208 Volt).
7. Make sure the heater watts, BTU, and amps are within the electrical circuit’s capacity.
8. Install a protective device, such as a 20 Amp time-delay fuse or breaker, to prevent electrical overload.
9. Follow the recommended minimum circuit requirement of 20 Amps.
10. Refer to the user manual for any additional safety precautions or maintenance instructions.

DIMENSIONS AND INSTALLATION

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

WALL CASE DIMENSIONS
RAB80 WALL SLEEVE Heavy-gauge galvanized steel, with insulation, for quick self-assembly. A – 42”, B – 13-3/4”, C – 16”

MAXIMUM CORD EXTENSION
WALL OPENING DIMENSIONS Add 1/4” to A and C dimensions for all cut-outs. RAB80 16-1/4” Min. H x 42-1/4” Min. W

ELECTRICAL WIRING

All wiring, including installation of receptacle, must be made in accordance with local electrical codes and regulations.
NOTE : Aluminum wiring may pose special problems – consult a qualified electrician.

GRILLE OPTIONS

• Stamped Aluminum Grille – RAG70

ELECTRICAL CONNECTION

• 230/208 volt units must be plugged into a receptacle. Installation must comply with local electrical codes and regulations.
• Power cord is permanently attached on all Hotpoint chassis

SPECIFICATION

AH12 ELECTRIC HEATER

230/208 VOLT| LINE CORD CONNECTED UNITS
Heater Watts| 3,500 / 2,897
Heater BTU| 10,900 / 8,900
Heater Amps| 15.3 / 13.7
Min Circuit| 20
Recommended protective Device| 20 amp time-delay fuse or breaker

FEATURE AND BENEFITS

• 14,500 / 14,300 cooling BTU
• 10.3 / 10.4 EER
• R32 Refrigerant – Environmental friendly, low GWP (Global Warming Potential)
• 3-Speed Fan – Give guests control over their comfort with three fan speeds to choose from
• 4-Temperature Limiting Options – Easily select one of four temperature ranges for peak efficiency and total customer comfort
• Intuitive Display – Allow guests to easily customize their preferred settings and reduce maintenance calls with an easy-to-use control panel
• Power Cord (LCDI) Included – Hotpoint PTACs come with everything needed for a quick and easy installation
• Automatic Emergency Heat – Keep guests comfortable with a heating option that uses electric resistance heat in heat pump mode
• Freeze and Frost Protection – Automatic freeze and indoor frost control keep units operating in peak condition
• Auto Power Recovery – In case of power failures, units automatically resume their operation when power restores, reducing maintenance calls
• Self Diagnostics – Quickly and easily identify service needs with a nine-point diagnostic code system
• Backed by an Industry Leader – With a long history of creating durable products at an affordable price, Hotpoint is your trusted PTAC brand

PRELIMINARY SPECIFICATIONS – SUBJECT TO CHANGE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>