PHILIPS SBM206 Voice Amplifier Speaker User Guide

: June 12, 2024
: Philips

PHILIPS SBM206 Voice Amplifier Speaker User Guide

Safety

Important Safety Instructions

Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Do not block any ventilation openings.Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registrers,stoves,or other devices (including amplifiers) that produce heat.
Only use attachments/accessories specified by the manufacturer.
Refer all servicing to qualified service personnel.
Servicing is required when the device has been damaged in any way,such as power- supply cord or plug is damaged,liquid has been spilled or objects have fallen into the device,the device has been exposed to rain or moisture,does not operate normally,or has been dropped.
Devices shall not be exposed to dripping or splashing.
Do not place any sources of danger on the device(e.g. liquid filled objects,lighted candle

Package Content

Before using your product,read all accompanying safety information.

Overview

```
1. AUDIO IN
```
1. MIC IN
SOURCE
1. ```
2. 
```
1. ```
2. HOOK
```
1. POWER ON/OFF VOL+-
USB
1. MICRO USB
POWER IN DICATOR
1. TF CARD
CHARGING INDICATOR

Charging

Power indicator status

Solid Blue while working.
Blinking Red continuously while low battery, and voice prompts will remind you the speaker is running out of battery.

Charging indicator status

Solid Red while charging. Red indicator off when get fully charged.

Tips: It takes around 3 hours to get the battery fully charged.

Power

Power On/Off

Rotate the volume knob clockwise/anticlockwise to turn the speaker on or off.
Tips: When the speaker is not connected with any signal source and there is no operation for 15 minutes. The speaker will automatically enter into power-saving mode.
You need to switch the knob off and then switch on to wake up the speaker.

Microphone

Wired Microphone Instructions

Please direct the positive hole of the wired microphone to your mouth when using . If you do not direct the positive side to your mouth,it might be howling or weak sound.Please do not forget to use with the black cotton.The black cotton can filter the interfering sound with the airflow

Recording

Recording Mode

Make sure there is a USB flash disk or a Micro SD card inserted in the speaker, and the speaker is connected with a wired Microphone. Short press SOURCE key to switch to Recording mode, then the red light indicator will be solid blue. Short press to start recording, Red indicator will keep flashing quickly. Short press to pause recording, Red indicator will stop flashing. Short press again to continue recording. Press and hold key or SOURCE key for 2 seconds to store the audio file. Press SOURCE key to switch to MP3 mode.
And press / to search for your recorded file.

AUDIO

AUDIO IN Mode

Connect your Audio in cable to the AUDIO IN socket, there will be voice prompts and the speaker will enter into the AU D10 IN mode automatically.

SD Card

MP3 Mode Instructions

Set loop one/ loop all playing: In MP3 mode,the default setting is loop all. If you want to play current track repeatedly, press and hold for 2 seconds while playing,and there will be voice prompts to tell you the loop one function has been enabled.To enable the loop all function,press and hold for 2 seconds again, there will be voice prompts to tell you the loop all function has been enabled.USB flash disk and TF card support 32GB max. Audio format: support MP3 / WMA / WAV (sampling frequency 8k~48k)

Exploded View

Always bring your product to a professional to remove the built-in battery.

Specifications

Amplifier

Rated Output Power| 3W RMS
Signal to Noise Ratio| 50dBA
Aux Input| 600mV RMS, 22 kohm

General information

Never remove the casing of this apparatus.
Never lubricate any part of this apparatus.
Never place this apparatus on other electrical equipment.

---|---

Notice

Any Changes or modifications made to this device that are not expressly approved by MMD Hong Kong Holding Limited may void the user’s authority to operate the equipment.

Disposal of your old product

Your product is designed and manufactured with high quality materials and components,which can fil be recycled and reused.

Do not throw away the product with the normal household waste at the end of its life,but hand it in at an official collection point or recycling. By doing this,you help to preserve the environment.

|

Removal of the built-in battery invalidates the warrantty and may destroy the product

---|---

Environmental information
All unnecessary packaging has been omitted.We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags,protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
Please observe the local regulations regarding the disposal of packaging materials,exhausted batteries and old equipment.

****|

The type plate is located on the bottom of the apparatus.

---|---

Names and Contents of Hazardous Substances

Name of the Parts	Hazardous Substances
(Pb, Lead)	* (Hg, Mercury)
Housing	○
Loudspeakers	○
PWBs	✕
Accessories (Cables)	✕

The table is compiled according to SJ/T 11364

○: Indicates that this hazardous substanc contained in all of the homogeneous materials for this part is below the limit requirement in B/T 26572

✕: Indicates that this hazardous substanc cont ained in at least one of the homogeneous materials used for this part is above the limit req irement in GB/T 26572.

| Environmental Protection Use Period
---|---

This logo refers to the period (10 years) d ring which the hazardous substances in electronic and electrical products will not leak o r mutate o that the use of these [substances] will not result in any severe environmental pollution,any b dily injury o r damage to any assets.

2021 © MMD Hong Kong Holding Limited. All rights reserved. Specifications are subject to change without notice.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.
CN-SBM200/93-UM-3.0