SIKO ZPRKU60LED Mirror with heated film and Naturel Project sensor Instruction Manual

SIKO ZPRKU60LED Mirror with heated film and Naturel Project sensor Instruction Manual

Installation Manual

General Information, Purpose of Use
Before first use, the user is required to properly consult this Installation Manual to ensure safe and trouble-free use of the product. This is a stationary LED luminaire designed to illuminate indoor areas such as bathrooms, corridors, etc. The luminaire is designed as a mirror with the light source located behind the mirror. The mirror is thus particularly suitable for use as decorative lighting. LED mirrors are mirrors illuminated by powerful LED strips with low power consumption and bright luminosity. The lifetime of the LEDs is up to 50,000 hours.

Safety Instructions
Any handling, maintenance or installation must comply with the basic safety requirements imposed by the activity. Follow any other safety instructions in this manual.

• The instructions so marked are primarily to prevent general danger or personal injury.
• The instructions so marked are primarily to Electric danger or personal injury from electrical hazards.
• Connection to the mains must only be carried out by a person with an electrical qualification
• Bathroom mirror connection conditions:
  • The mirror must be installed in accordance with the applicable safety regulations.
  • The product may be connected to a fixed supply in a 1NPE 230V 50Hz TN-S network.
  • Pre-wired protection max: 10A and current protector RCD 30 mA.

Handling
The luminaire is supplied packed in a carton and covered with foil protected by polystyrene lining. Due to its extra weight and large size, please handle the luminaire very carefully. The luminaire is equipped with a mirror which is very fragile and can easily break. For square mirrors, leave the plastic protective corner covers on during handling and remove them after installation.

Installation

The luminaire is intended primarily for mounting on a wall or other surface designed for indoor use. The luminaire can be installed in the washbasin area and in areas with a bathtub or shower outside the 0+1+2 zone (see pictures in the Assembly Instructions). The electrical installation must be carried out by a person with an electrical qualification. The connection is carried out by: a) moving supply b) connecting the supply cable (at the back of the mirror) to the existing wiring in the wiring box preferably located behind the mirror. If there is already a connection cable on the wall, it can be connected via the terminal box to the connection cable on the back of the mirror.

Maintenance

Warranty Period
The product is covered by warranty within the meaning of the Civil Code. The manufacturer provides warranty of 24 months from the product purchase. Any handling and operations other than those recommended in this manual are prohibited.

Technical Specifications

Power supply : 230 V AC 50 Hz, L+N
Pre-wired protection : 10 A max RCD (Fi) 30 mA.
Input: 5-50 Watt
Electrical class : I.
Light source: LED strip, warm light / daylight / cold light
Light source service life : up to 50 k hours
Ballast: 1–2 x electronic ballast for 12 V DC SELF
Protection: IP 44

The light source of this luminaire is non-replaceable, the whole luminaire must be replaced at the end of its service life!
Electric Diagram
Products: ZPRKU60LED

Assembly Instructions

The luminaire can be installed in the washbasin area and in areas with a bathtub or shower outside the 0+1+2 zone (see pictures in the Assembly Instructions). The electrical installation must be carried out by a person with an electrical qualification. The connection is carried out by: a) moving supply b) connecting the supply cable (at the back of the mirror) to the existing wiring in the wiring box preferably located behind the mirror. If there is already a connection cable on the wall, it can be connected via the terminal box to the connection cable on the back of the mirror.

For assembly use a dowel and a screw (not included).

First, prepare the mirror location. The easiest way to select the correct position of the mirror is to directly place the mirror in the desired location on the wall and check if the position suits you

Install outside the 0+1+2 zone

Bathtub side view

Installation Manual

Connect the mirror‘s connecting cable to the socket or cut the plug and connect the mirror‘s connecting cable to the mains cable or electrical box. You can use a connection terminal block with IP protection for bathroom equipment to connect the cables. Make sure there is no electricity in the supply cable before starting the connection!!! Connect the power cable of the luminaire to the power supply on conductors L and N. The terminal block is not included in the product. Use only the recommended supply voltage 230 V AC, 50 Hz, L and N with pre set fuse of max. 16 A

Use
The sensor has memory. When the mirror is switched off and then switched on, the last set colour and light intensity is use

 Declaration of Conformity

EU Declaration of Conformity
The product is covered by a declaration of conformity according to the relevant applicable regulations. Product description: Bathroom luminaire with illuminated mirror surface

Name: LED bathroom mirror
Model: ZPRKU60LED

The product complies with the requirements of these regulations:

• Government Decree No. 117/2016 Coll., on conformity assessment of products in terms of electromagnetic compatibility in delivering them to the market

• Government Decree No. 118/2016 Coll., on conformity assessment of electrical equipment designed for use within certain voltag limits in delivering them to the market and harmonised standards:

• ČSN EN 60598-1-ed.6 (360600) Luminaires – Part 1: General Requirements and Tests.

• ČSN EN 60598-1-ed.6:2015/Oprava1 (360600) Luminaires – Part 1: General Requirements and Tests.

• ČSN EN 60598-2- 1 (360600) Luminaires – Part 2: Special Requirements – Section 1: Stationary Luminaires

The last two digits of the year in which the CE marking was affixed: 20
The device bears the mark of conformity

SIKO KOUPELNY a.s.
Skorkovská 1310, 198 00 Praha 9
IČ: 26065801
CZECH REPUBLIC

Documents / Resources

| SIKO ZPRKU60LED Mirror with heated film and Naturel Project sensor [pdf] Instruction Manual
ZPRKU60LED Mirror with heated film and Naturel Project sensor, ZPRKU60LED, Mirror with heated film and Naturel Project sensor, with heated film and Naturel Project sensor, film and Naturel Project sensor, and Naturel Project sensor, Naturel Project sensor, Project sensor, Project
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>