GROWERS CHOICE GHS-730 LED Grow Light User Manual

: June 4, 2024
: GROWERS CHOICE

Table of Contents

GROWERS CHOICE GHS-730 LED Grow Light
introduction
SPECIFICATIONS
SAFETY WARNINGS:
CAUTION – RISK OF PERSONAL INJURY
Contents:
installation
Other Installation Options
CONTROLLABILLITY:
Warranty:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GROWERS CHOICE GHS-730 LED Grow Light

introduction

Introducing the New GHS-730, this sturdy commercial-grade light is designed and built for use in commercial horticultural facilities. The GHS-730 delivers one of the highest light outputs in the industry at 730W with excellent thermal management. Its sleek linear design eliminates unwanted shadows and makes it ideal for supplemental lighting in greenhouses. As an added benefit this fixture is also compatible with our CPS (Central Power Solutions.

SPECIFICATIONS

Speciﬁcations

Model

Item

Model

| 120V| 208V| 240V| 277V
---|---|---|---|---
GHS-730| 6.6A| 4.6A| 3.6A| 2.9A

PPF calculations ccomplied using our in-house integrating sphere measurements and typical spectroadiometric data for each LED to determine the fixture performance. Actual photometric results may vary within the LED’s manufacturer’s bin tolerance.
Wattage values are typical expected values. TSL Horti Tech maintains and tolerance of +/- 10% range on flux and power consumption. Target light level can vary from projected levels depending on ambient temperature, room reflections values, and other cond

SAFETY WARNINGS:

The GHS-730 is a passively cooled system with no moving components. Do not try to open or disassemble the fixture, it contains no service parts inside. Doing so May cause harm to the fixture and void warranty

Always adhere to the local rules and regulations when installing or using the fixture.
Wearing protective gloves and glasses is recommended during installation.
Always disconnect from power source before performing any maintenance to the fixture.
The fixture will get hot during operation. Do not touch while the light is on. Keep this product away from children.
Always allow at least 10 minutes for the fixture to cool down betore handling.
Do not touch the LED diodes.
Keep the power cord away from hot surfaces.
Do not plug this system into a supply voltage other than what is instructed on the fixture.
Do not use the fixture when the power cord is damaged.
Do not use the fixtures if the unit has been dropped, and there is damage to the enclosure or bars.

WARNING
Risk of electrical shock. To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before moving or cleaning.

CAUTION
To reduce the risk of overheating or fire, never place operating fixtures face down on a flush surface. Always allow for adequate ventilation of fixtures and power supplies.

CAUTION
LED and heat sink surfaces may be hot. Allow sufficient cooling time before handling.

CAUTION – RISK OF PERSONAL INJURY

Disconnect power before servicing or installing fixture. Lighted fixture may be hot. To reduce risk of injury, turn off or disconnect power and allow to cool before handling. Fixture must be grounded in accordance with appropriate codes. Failure to do so may result in serious injury or death. Be sure all power is off prior to installing fixture.

installation

Remove your GHS-730 from its packaging. (Do not remove the diode strip protective plastic).
Place the included metal hangers on the desired beam. After this insert it into the mounting holes at both ends of the unit.
Next mount the driver using the S shaped metal hangers provided on the same beam.
After the beam installation plug in the power cord with M25 adapter at each end and plug them from your unit to its driver.
Then take your power cord with and plug in the M25 adapter into the driver.
Lastly remove the protective plastic from the diode strip.

Other Installation Options

For other installation methods refer to the provided charts. Mounting/hanging gear not included.

CONTROLLABILLITY:

The GHS-730 are fully controllable with a controller or through a Central Power System (CPS). lf using a controller you will need RJ14 data cords.

Warranty:

TSL Horti Tech and Grower’s Choice warrants the mechanical and electronic components of their product to be free from defects in material and workmanship if used under normal operation conditions for a period of 1 year from the original date of purchase. If the product shows any defects within this period and that defect is not due to user error or improper use, TSL Horti Tech and Grower’s Choice shall, at its direction, either replace or repair the product using suitable new or reconditioned products or parts. TSL Horti Tech and Grower’s Choice warranty liability extends only to the replacement cost of the product. In case TSL Horti Tech and Grower’s Choice decides to replace the entire product, the limited warranty shall apply to the replacement product for the remaining initial warranty period. TSL Horti Tech and Growers Choice shall not be held responsible for any damage caused by the operation of the unit, be it incidental or consequential or any type including, without limitation, damage or injury caused to other products or machinery or buildings. Nor will responsibility be accepted for loss of time or profit, or for any inconvenience caused in any way whatsoever.

Tel: 909-972-8419
E-mail: info@growersc.com
Website: www.growersc.com
Address: 2510 E Merrill Ave. Ontario CA 91762