DI LUSSO CH606SS Canopy Rangehood User Manual

DI LUSSO CH606SS Canopy Rangehood

Product Information

The Canopy Rangehood is a kitchen appliance designed to remove smoke, odors, and grease from the air during cooking. It is available in two models: CH606SS and CH906SS. This appliance is easy to use and maintain, providing efficient ventilation for any kitchen.

Product Specifications

• Model: CH606SS, CH906SS
• Installation   and Operation Manual Version: 1.0

Important Notes

• This appliance is not intended for use by individuals (including children) with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction regarding the use of the appliance by a responsible person.
• Children should be supervised when the product is in operation to prevent them from going near the range hood.
• This product must be connected in accordance with current electrical regulations. A fixed wiring installation should only be done by an authorized electrician.
• The appliance must be earthed, and means for disconnection should be incorporated in the fixed wiring according to wiring rules.
• Never modify any part of this appliance. Modification should only be done at the user’s own risk.
• Before maintenance or cleaning, disconnect the appliance from the mains.
• For repairs, always contact an authorized Customer Service Centre and ask for original spare parts. Repairs by untrained individuals may lead to damage and void the warranty.
• Packaging cling film, polystyrene, and plastic wrappings must be kept out of reach of babies and young children to avoid suffocation.
• Do not connect the appliance if there are obvious signs of transportation damage. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent.
• Ensure the location where the appliance is installed has good, permanent ventilation.
• The distance between the bench top and the lower part of the hood should be between 65 cm and 75 cm for optimal operation.
• Do not leave lit gas burners exposed due to the risk of fire.
• The exhaust from the canopy range hood must not be discharged into any heating flue.
• This product must not be disposed of with domestic waste. It should be disposed of at an authorized recycling bin for appliances.
• There is a risk of catching fire if cleaning is not carried out in accordance with the suggested frequency and instructions.
• The manufacturer shall not be liable for any direct or indirect damage caused by faulty installation. The installer must ensure that the product installation and connection comply with the local and general regulations in force.

Product Usage Instructions

1. Read the entire user manual carefully before installing and operating the canopy rangehood.

2. Ensure that the installation is done by an authorized
   electrician in accordance with current electrical regulations.

3. Earth the appliance and incorporate means for disconnection in the fixed wiring as per wiring rules.

4. Keep children supervised when the product is in operation to prevent them from going near the range hood.

5. Disconnect the appliance from the mains before performing any maintenance or cleaning.

6. In case of repairs, contact an authorized Customer Service Centre and request original spare parts.

7. Dispose of packaging materials safely, keeping them out of reach of babies and young children.

8. Ensure the location where the appliance is installed has good, permanent ventilation.

9. Position the canopy range hood at a distance of at least 65 cm and not more than 75 cm from the bench top for optimal operation.

10. Avoid leaving lit gas burners exposed to reduce the risk of fire.

11. Do not discharge the exhaust from the range hood into any heating flue.

12. Dispose of the product at an authorized recycling bin instead of domestic waste.

13. Do not use the appliance if you have reduced physical, sensory, or mental capabilities, unless supervised by someone responsible for your safety.

14. Clean the canopy range hood regularly as per the suggested frequency and instructions to avoid the risk of fire.

To avoid the risk of accident or damage to the appliance, it is essential to read the following instructions prior to product installation and / or first time usage.

Important Notes

Dear Customer

• Thank you for choosing our product. This appliance is easy to use; however please read this handbook carefully before installing and operang it. Herein, you will find the  correct  method  of  installation and pass  for  best  use  and  maintenance  of  the  product.
• This appliance is designed to be handy for any adult to use at home. Do not allow children to play with it. Children need to be supervised when the product is in operation so that they do not go near the range hood.
• This product must be connected in accordance with current electrical regulations. A fixed wiring installation is to be done only by an authorised electrician.
• WARNING: THIS APPLIANCE MUST BE EARTHED.
• Means for disconnection must be incorporated accordance with the wiring rules. in the fixed wiring in

Electrical Connection :

• Green & yellow: EARTH
• Blue: NEUTRAL
• Brown: LIVE
• Fixed wiring must be protected.
• Never use reductions, shunts, adaptors that can cause overheating or burning.
• It is strictly prohibited to modify any part of this appliance. Modification is to be done at user own risk.
• Before maintenance or cleaning of the product, disconnect the appliance from the mains.
• For any repairs, always contact authorized Customer Service Centre and ask for original spare parts. Repairs by untrained people may lead to damage and void the warranty.
• Packaging cling film, polystyrene and plastic wrappings must be kept out of reach of babies and young children to avoid suffocation.
• Do not connect the appliance if there are obvious signs of transportation damage. If the supply cord is damage, it must be replaced by the manufacturer, or its service agent as mentioned in Clause 7 (60335-2-31)
• Ensure the location in which this appliance is installed has good, permanent ventilation.
• The distance between the bench top to the lower part of the hood must not be at less than 65 cm and it is not recommended to be more than 75 cm for optimal operation.
• Do not leave lit gas burners exposed due to risk of fire.
• The exhaust from the canopy range hood must not be discharged into any heating flue.
• This product must not be disposed with the domestic waste. It has to be disposed at an authorised bin for recycling the appliances.
• This appliance is not intended for use by person (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge. Unless, they have been given supervision or instruction regarding the use of appliance by personnel who is responsible for their safety.
• There is risk of catching fire if cleaning is not carried out in accordance with the frequency suggested and instructions
• The manufacturer shall not be liable for any direct or indirect damage caused by faulty installation. The installer must ensure that the product installation and connection complies with the local and general regulation in force.

Product Specification

CH606SS / CH906SS

• Voltage / Frequency : 220‐240Vac / 50Hz
• Rated Power : 213W
• Rated Motor : 210 W
• Motor Capacity : 600m3/hr
• Filter : Aluminium & Charcoal (OpƟonal)
• LighƟng : LED round light
• Speed Seƫngs : 3 speed
• DucƟng : Ducted OR RecirculaƟon

External Dimension

Dimension

Model

|

L

|

H1

|

H2

|

H3

---|---|---|---|---

CH606SS

|

600mm

|

238mm

|

500mm

|

490mm

CH906SS

|

900mm

|

238mm

|

500mm

|

490mm

Product Overview

• Complete product comes with the following :
• Model : CH606SS / CH906SS
• 1 x chimney rangehood body with integrated motor, controls & light
• 1 x user manual & warranty card
• Fixing brackets & screws
• A. Canopy Section with integrated motor
• B. Lower Chimney Cover
• C. Upper Chimney Cover
• D. Flange (Optional)
• E. Duct Pipe
• F. Charcoal Filter (Optional)
• G. 7pcs of screw 5*50
• H. 7pcs of wall plugs
• I. 6pcs of screws 4.2*9.5
• J. Hood fixing bracket
• K. Chimney mounting bracket

Dimensions unit ：mm

Installation Instruction

To install the chimney hood body, predetermine a location and follow the below instructions

Wall marking:

• Draw a vertical line on the wall where the chimney is to be installed.
• Draw a horizontal line A at 920mm above the hob. Mark at 80mm offset left and right from the vertical line. These two holes are for hood fixing bracket.
• Next, adjust the height according to upper chimney cover, draw a horizontal line B at 490-910mm above line A. Mark at 40mm offset left and right from the vertical line. These two holes are for upper chimney cover.
• Draw a horizontal line C at 190mm below line A. Mark at 170mm offset left and right from the vertical line. These two holes are to mount the hood body.
• Drill holes at the marking points with a 10mm drill bit.
• Insert the wall plugs and fix the two brackets by using the screws (5*50) supplied at line A & B.
• Mount the hood body to the hood mounting bracket. Level the hood body correctly. Remove the aluminium filter from the bottom of the hood body, fix 2 screws (5*50) and wall plugs at points marked at line C.

Ducted mode (Vented mode)

• In the ducted mode, air is drawn into the hood. Oil is trapped in the aluminium filter while odours, fumes and condensation are then directed and vented to the outside.
• Only the aluminium filters is to be installed in the ducted mode.
• Ductwork should be planned carefully before drilling and cutting the duct.
• Installer must ensure that the product installation and connection complies with the local and general ducting regulation in force. Flexible ductwork is recommended.
• Extend duct to its full length, and position, cut and discard any excess. Note : Keep duct as straight as possible for maximum air flow and at least restrictions, while providing for easy maintenance
• Vented system must be terminated to the outside. Ductwork can extend either through the wall or the roof. Do not terminate the vent system in an attic or other enclosed area.
• The length of the ductwork and the number of elbows should be kept to minimum to provide efficient performance. The size of the ductwork should be uniform. Do not install two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or floor opening around the cap.
• When the hood is working at the same time with other non-electrical cooking equipment, the negative pressure of the room must not exceed 4Pa.
• Make sure there is proper clearance within the wall or floor for exhaust duct before making cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud is to be cut, then a supporting frame have to be constructed.
• Connect the Ø150mm duct pipe from the hood body to exit / vent point of the hood. Fix the duct pipe in position by ring clamps (not provided by manufacturer)
• Make sure the charcoal filter is removed (if any).

Recirculation Mode

• In the recirculation mode, air is drawn into the hood. Oil is trapped in the aluminium filters while cooking odours is removed by the charcoal filter.
• Purified air then is directed back to the kitchen.
• In this mode, charcoal filter is strongly recommended to be fitted to the rangehood.
• Connect the outlet connection to the hood body using a Ø 150mm pipe.
• Ensure that the charcoal filters is installed in position.

Chimney Assembly

Lower chimney

• Slightly widen the two sides of the chimney and secure the lower parts laterally to the hood body by using two 4.2*9.5 screws provided.

Upper chimney

• Slightly widen the two sides of the upper chimney and secure it at the mounting bracket at line B, make sure that it is fitted firm.
• Secure the sides of the brackets by using two 4.2*9.5 screws provided.
• Note : To avoid scratching the chimney during installation, do NOT to peel the protective film off until both upper & lower chimneys are fixed in place. After both chimneys are secured and fixed, use a blade to gently cut the film where the chimney joins to cleanly remove the film.

Electrical Connection

• Before connecting to the mains, make sure that
• The electric meter, fuse, feeding line and socket are adequate to withstand the maximum load required (refer to product data label for rated power)
• The supply system is regularly earthed, according to the regulations in force.
• The isolation switch can easily be reached after the rangehood is installed.

Rangehood Operation & Control

• The hood is equipped with a 3-speed control motor. Electronic control buttons are located at the front edge of the hood canopy.

• To achieve better results, it is recommended to switch the hood on 3 to 5 mins before cooking starts. Likewise, let the hood run for a few minutes after cooking.

• Light on / Off

• To turn the lighting system on and off.

• Fan On / Off at Low Speed

• To turn the extractor motor On or Off at low speed. This mode provides a continuous and low volume extraction in the presence of light cooking vapours.

• Fan On / Off at Medium Speed

• To turn the extractor motor On or Off at medium speed. Suitable for most operating conditions. This mode provides the optimum treated air ow to noise level ratio.

• Fan On / Off at High Speed

• To turn the extractor motor On or Off at high speed. Suitable for eliminating the high levels of cooking vapours and long cooking period.

• Power Off

• To turn off motor operation.

Cleaning & Maintenance

• Caution: Prior to cleaning or maintenance, always disconnect the power supply.
• Do not use a steam cleaner.
• To ensure the range hood is functioning effectively, regular maintenance is a must.
• Warning: a build-up of oil may occur if the range hood is not cleaned regularly
• Surfaces : Clean with warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool or solvents on any part of this appliance as this will cause irreparable damage. Dry the rangehood by using a cloth that does not pro- duce fluff.
• Aluminium Filter : Remove the filters one by one pushing them towards the back side of the hood and simultaneously pulling downwards. Any kind of bending the filters has to be avoided when washing them. This could be washed in a dishwasher.
• It is advisable to stack them vertically to avoid food residue sticking to them. Or soak the aluminium filter in a degreasing agent until all grease is dissolved. Then clean it under a flowing water tap, and rinse it off. Before fitting them back to the hood, make sure the filters are completely dry.
• Note: Frame discolouration may occur if the filter is washed in a dishwasher.
• Charcoal Filter (Recirculation installation) : The charcoal filter should be replaced when it is noticeably dirty or discoloured (usually after 4 to 6 months, depending on the usage). It is not washable and cannot be regenerated. The charcoal filter must be replaced with a similar and appropriate type. Clogged filters restrict airflow and may cause of overheating the extractor motor.

To replace the charcoal filter:

• First remove the Aluminium filter from the hood body
• Remove the charcoal filter from the hood motor by turning it according to the picture below :
• Fit new charcoal filters to the hood motor.
• Fit the Aluminium filter back in place.

Troubleshooting

mains properly
Reset the circuit breaker
Poor Airflow| Aluminium filter is clogged| Clean the filter and refit it after it is dry
Charcoal filter is clogged| Replace with new charcoal

filters

Motor is running but there is no airflow| Butterfly valve is jammed| Contact the service agent
Poor Extraction rate| Inadequate ventilation| Ensure the kitchen ventilation is good to allow entry of fresh air
Charcoal filters are not installed| Install the charcoal filters for setting in recirculation mode
Motor cuts out after a few minutes| High temperature safety device is activated| Check if the kitchen ventilation is good and sufficient
The distance between the hood in‐

stalled and the cooking stove is short

| Make sure the hood is installed at a minimum of 65cm above the cooking stove
Oil dripping to the stove| Aluminium filter is satu‐ rated| Clean the filter and refit it after it is dry
Whirring sound dur‐ ing hood operation| Foreign object in

contact with the fan blade

| Contact the service agent
Lamps do not light up| Light module is burnt out.| Contact the service agent. Light bulb cannot be replaced solely, the entire light module has to be replaced by service agent

Light Module Replacement

• Warning! This has to be done by licensed electrician.
• The light blubs cannot be replaced by user, the entire light module has to be replaced by a licensed electrician.
• When changing the light module, the contacts are live.
• Unplug the appliance from the mains or switch off the circuit breaker before the replacement takes place.
• Remove the Aluminium filters from the hood body.
• Disconnect the LED terminals.
• Press the LED from the back of the front panel, remove the LED.
• Replace the module with new one. It is a commercially available LED module (max 1.5W)

Diameter: 70mm

| —| DSR-1.5-S-70

Schematic Diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>