NEXTORCH WL60 Green Aiming Laser Sight User Manual

: June 4, 2024
: NEXTORCH

Table of Contents

Features
INSTRUCTIONS
LASER SIGHT ZEROING
SPECIFICATIONS
MAINTENANCE
WARRANTY
CONTACT WITH EXTORTIONER DESIGNER
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NEXTORCH WL60 Green Aiming Laser Sight User Manual

Features

Co-aligned visible white light and green laser
Attaches securely to MIL-STD-1913 rail.
Features laser calibration function for accurate sight.
Remote pressure switch features momentary and constant on operation.

INSTRUCTIONS

Battery Replacement

Powered by 1 × 18650
or 2 × CR123A batteries
Battery Replacement

Mounting and Removal

Push down the locking block and Loosen the mounting screw on the rail grabber bracket until the jaws have sufficient space to fit over the weapon rail.
Make the WL60 with the laser apertures facing in the direction of the muzzle of the weapon, and put it in the desired recoil groove of the rail.
Turn the mounting screw clockwise as tightly as fingers allow. Then use a screwdriver or similar tool to tighten the screws.

Switch Operation

Press switch

for white light momentary on.
for green laser momentary on.
for white light and green laser momentary on.
for white light constant on,
press again within 3 seconds to switch mode, long press for 3 seconds to enter strobe mode when the white light is on.
for green laser constant on

Remote Switch

The Remote Switch plugs into the remote jack as shown in Figure. It is then secured to the weapon to best suit the operator’s firing preference using the retaining straps or hook and loop fastener tape.

WARNING
Failure to properly secure the WL60 to the rail may lead to boresight repeatability and zeroing issues.

LASER SIGHT ZEROING

The following table indicates the direction of adjuster rotation and laser sight movement when the WL60 is TOP Mounted.
Each 1 / 4 turn of the adjuster will move the laser sight by 37 cm at 50 meters (or 100 cm at 150 meters)

Adjuster	Rotation	Laser Sight Movement
U / D Adjuster	CW CCW	Up Down
L / R Adjuster	CW CCW	Right Left

SPECIFICATIONS

ANSI / PLATO-FL1| High (White)| Low (White)| Green Laser| High (White) + Green Laser
---|---|---|---|---
Light Output | 700 lm| 100 lm| ≤ 5 mW| －
Run Time | 1 h 30 min| 12 h| 40 h| 1 h
Beam Distance | 320 m| 122 m| －| －
Impact Resistance | 2 m
Waterproof | IPX7，1m
Weight and Dimensions| Weight: 219 g (Without Battery) Size: 116 mm (Length) × 72 mm (Width) × 33 mm (Height)
Material| Light Source: LED / Laser transmitter Aluminum + PA
Battery| 1 × 18650 / 2 × CR123A

Above tested specifications are strictly based on the standard of ANSI / PLATO-FL1. We tested WL60 with 1 × 18650 battery in 22 °C ± 3 °C. The specifications might be different when using a different battery or testing in a different environment.

MAINTENANCE

Being infected with seawater or any corrosive chemicals, please rinse immediately with clean water.
Please use high quality batteries; Remove batteries when not working for a long time, and then store in a cool dry place.
Replace waterproof O-ring immediately when considering of the damage with use.

WARRANTY

NEXTORCH warrants our products to be free from any defects in workmanship and/or materials for a period of 15-day from the date of purchase. We will replace it. NEXTORCH reserves the right to replace an obsolete product with a current production, like model.
NEXTORCH warrants our products to be free of defect for 5-year of use. We will repair it.
The warranty excludes other accessories, but rechargeable batteries are warranted for 1year from the date of purchase.
In the event that any issue with a NEXTORCH product is not covered under this warranty, NEXTORCH can arrange to have the product repaired for a reasonable fee.
You could access to NEXTORCH website (www.nextorch.com) to gain warranty service information by scanning the following QR code.You could also:
Email us at: service@nextorch.com
Call us: 0086-400-8300-799
OR contact your local dealer/distributor.

CONTACT WITH EXTORTIONER DESIGNER

In order to improve NEXTORCH, we appreciate you could offer our designers your after-use feedback and creative suggestions by scanning the following QR code. Thank you!