Kaiser A 6315 Empire Cooker Hood User Manual

: June 12, 2024
: Kaiser

Table of Contents

INSTALLATION INSTRUCTIONS
SAFETY REGULATIONS
BRIEF DESCRIPTION
LOCATION DRAWING
OPERATING CONDITIONS
OPERATION MODE OF THE HOOD
USAGE
ELECTRONIC CONTROL
CARE AND MAINTENANCE
RESPECT FOR THE ENVIRONMENT
Documents / Resources

A 6315 Empire Cooker Hood
**User Manual

**

DEAR CUSTOMERS,
thank you for purchasing this Kaiser product.
We are convinced that you have made a right choice. This product which satisfies the high quality demands and corresponds to world comprehensive standards realizes your cooker hood, and his modern appearance which has been developed by the best European designers will decorate your kitchen splendidly.
We ask you to read the operating instructions before usage thoroughly. The consideration of recommendations protects you from possible inconveniences which can appear as a result of the wrong use of the hood, and allows you to reduce the consumption of electric energy. If the use corresponds to the present operating instructions, the hood will bring you a lot of pleasure for a long time.
Our cooker hoods correspond to the main demands of the security, hygiene and environment protection, according to the directives of the EU which is confirmed with certificates DIN ISO 9001, ISO 1400, according to the norms counting within the frames of the EU, they also correspond to the Gosstandart of Russia, standards of the CIS, which is confirmed with the corresponding certificates.
With the thoughts of a constant improvement of the quality of our cooker hoods the changes in design and equipment which lead only to positive changes of the technical qualities are reserved by the manufacturer.
We wish you an effective use of the cooker hood of our firm.
Yours faithfully
OLAN-Haushaltsgeräte
Berlin Germany
We Inform you that our devices which are the object of the present operating instructions are precertain exclusively for the domestic use.

INSTALLATION INSTRUCTIONS

INSTALLATION OF THE HOOD

Kaiser A 6315 Empire Cooker Hood odule - HOOD

Trace a vertical line on the wall to indicate the centre of the cooker plate.
Place the hood body 1 on the wall to get min 650 mm from the cooker plate (see p. 12). Level it horizontally. Use the top of the rear side of the hood as ruler to trace the line.
Mark the mounting holes on the wall.
Drill the holes as indicated on the wall, using drills of diameter 8 mm, drive the plugs in.
Hang the hood body 1using the screws.
If the cooker hood will be use in extractor mode it is necessary to mount a vent conduit of Ø 150 mm on the fixed V-flap. By connection of a conduit of Ø 120 mm use an adapter 3.
f the cooker hood will be operate in odour I absorber mode it is necessary to install charcoal filter ( see p. 18).
Attach the telescopic column 5 on the masking cover 4 of the mounted hood.
Pull out the masking cover 5 on the demanded height. Mark the level of the mounting holes. Remove the masking cover.
Place the hanger of the top masking cover 6 at the level of mounting holes and install the hanger.
Hang the masking cover column 5 to the hood’s body and to the wall hanger using appropriate screws.
Connect the hood to the power supply network.

Models A 6135 Em, A 9315Em – 220-240V; 238W
CONNECTING TO THE POWER NETWORK
Before connecting the oven to the mains power supply, make sure that:

The supply voltage corresponds to the specifications on the data plate in the interior of the device.
The power network has an efficient ground connection complying with all applicable laws and regulations.

The according to the rules installed socket is a legal requirement. The power cable should never reach a temperature 50 °C above ambient temperature at any point along its length.
If the appliance is to be connected directly to mains terminals, fit a switch with minimum aperture of 3 mm between the contacts. Make sure that the switch is of sufficient capacity for the power specified on the appliance’s data plate, and compliant with applicable regulations. The switch must not break the yellowgreen earth wire.
The socket or switch must be easily reachable with the oven fully installed.
After connecting the device to the power supply network (in accordance with the requirements defined above) it is necessary to check the lighting of the hood and whether its motor works correctly.
Attention! The manufacturer declines all responsibility for damage or injury if the above instructions and normal safety precautions are not respected

SAFETY REGULATIONS

Never let the children operate the machine.
The cooker hood is for home use only, not suitable for barbecue, roast shop and other commercial purpose.
Clean the cooker hood according to the instruction manual and keep the unit from danger of burning.
Direct suction from gas cooker is forbidden.
Please keep the kitchen room a good convection.
Before connecting this appliance check that the power supply cord is not damaged. A damage supply cord must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
Regulations for air discharge have to be fulfilled.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person slide for their safety.
Children should be supervised to ensure, that they do not play with the appliance.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Cleaning and user maintenance shall not be made by children without supervision.
Do not flambé under the range hood.
There is a fire risk if cleaning is not carried out in accordance with the instructions.

BRIEF DESCRIPTION

The cooker hood was designed to remove kitchen fumes. It requires installation of a conduit discharging used air to the outside. The conduit (usually a pipe Ø 150) shall not be longer than 4 – 5 m. The hood can operate as an odour absorber after installation of an charcoal filter. In such case a conduit discharging used air to the outside is not necessary, but it is recommended to install an air exhaust guide.
The cooker hood is an electrical appliance manufactured according to class I of shock protection.
It has its own lighting and an exhaust fan which can be set to one of four rotational speeds.
The hood was designed for permanent installation on a vertical wall over a gas or electric cooker.

LOCATION DRAWING

Arrangement of the functional elements:

Kaiser A 6315 Empire Cooker Hood odule - Hood body

Hood body, equipped with lights, engine unit and
electronic programmable control.
V-flap for the extracting conduit.
Conduit adapter 150-120 mm
Top telescopic masking column.
Wall hanger of the masking column.

OPERATING CONDITIONS

The cooker hood was designed for removal of kitchen fumes to the outside. It should be connected to an appropriate ventilation duct (do not connect the hood to any chimney, smoke or flue-gas ducts which are in use).
The device shall be installed at the distance of at least 650 mm above the working top of an electro and 700 mm above a gas cooker.
Do not leave open flame under the hood. When removing pots from the burners set the flame to its minimum level.
Any food cooked in fat shall be constantly monitored, since overheated fat can ignite very easily.
The grease filter of your cooker hood should be cleaned at least every 2 months, because a filter soaked with grease becomes easily flammable.
Pull the plug of the power cord from a wall socket beforeany cleaning, filter replacement or repair operation. Kaiser A 6315 Empire Cooker Hood odule -
CONDITIONS The room must be well aerated in case a hood and some other heat equipment fed with an energy other than electricity (gas, oil, coal heaters, etc) operate at the same time. In fact the intake hood, disposing of air, could create a vacuum in the room. The vacuum should not exceed 0,004 millibar. This prevents the gas exhausted by the heat source from being intaken again.
It is therefore advisable to ensure the room contains air taps able to ensure a steady flow of fresh air (this point does not apply when the hood is used as an odour absorber).
When connecting to 220 – 240 V power supply network use an electric socket in working order.

OPERATION MODE OF THE HOOD

AIR EXTRACTOR MODE
In extractor mode the air is discharged to the outside by a special conduit. Remove any charcoal filters in case if they have been installed by factory (see Replacement of the filter). This increases the performance of the cooker hood.
The hood can be connected to the opening discharging air to the outside by means of a rigid or flexible conduit of Ø 150 or 120 mm, and appropriate clamps for conduits which should be purchased in a shop selling installation materials.
A qualified installer should be commissioned to make the connection. ODOUR ABSORBER MODE
In this option filtered air returns to the room through cut outs on both sides of the top funnel, In this setting it is necessary to install the charcoal filter.
LEVELS OF THE ENGINE’S SPEED
The lowest and medium speeds should be used under normal conditions and with low concentration of fumes.
The top speed should be used in case of high concentration of kitchen fumes, e.g. during frying or grilling.

USAGE

OPERATIONAL SAFETY
All safety instructions included in this manual shall be observed without exception!
Grease filters and charcoal filters should be cleaned and replaced according to manufacturer’s instructions, or more frequently in periods of intensive use (more than 4 hours a day).
If a gas cooker is used it is forbidden to leave uncovered flame. When removing pots from gas burners set the flame to its minimum level.
Always make sure that flame does not extend outside the pot. Such a situation causes undesired energy losses and dangerous heat build-ups.
The hood should not be used for other purposes than those for which it was designed.

ELECTRONIC CONTROL

The buttons 1, 2 and 3 serve the purpose of selection of the engine speed in range from 1 to 3.

Push the button 1 to start the engine. The engine runs at 1st, lowest speed.
Push the button 2 to start the engine. The engine runs at 2nd, medium speed.
Push the button 3 to start the engine. The engine runs at 3rd, highest speed.
Push the button 0 to switch off the engine in any condition.

The button 4 is used to turn on and off the extraction hood lighting; independently of the engine work status, push this button to switch on/ off the lighting.

CARE AND MAINTENANCE

Regular maintenance and cleaning of the device will guarantee its good and fault-less operation, and extend its life. Attention should be paid to replacing grease and charcoal filters according to manufacturer’s instructions.

METAL GREASE FILTER

Cleaning
Grease filters should be cleaned every two months during normal operation of the hood, in a dishwasher or manually, using mild detergent or liquid soap. Dismantling

To dismantle the filter 1 proceed as follows:

Release the lock catch 2.
Remove the metal grease filter.

CHARCOAL FILTER

Operation
Charcoal filters can be used only when the cooker hood is not connected to any ventilation duct.
Filters with a charcoal can absorb odours until they are saturated. They cannot be washed or regenerated and should be replaced at least every 6 months or more frequently in case of very intensive use. Replacement of the filter

Remove the metal grease filter 1.
Dismantle the old filter 3 situated on the engine by rotating it counter-clockwise then install a new charcoal filter.

LIGHTING

The lighting system consists of halogen lamps or LEDs.
Replacement

Using a flat tool or screwdriver prise the frame of the halogen lamp or LED and holding it, remove 1 to the outside.
Replace the halogen lamp or LED using a piece of cloth or paper for that purpose.
Then reinstall the frame and the glass proceeding in reverse order.

Attention! Make sure that you do not touch the halogen bulb to be installed with your bare fingers use for that purpose a piece of cloth or paper!

CLEANING
The following shall be avoided during normal cleaning of the hood:

Wet cloth or sponge and water jet.
Solvents or alcohols which might dull lacquered surfaces.
Caustic agents, particularly in regard to cleaning stainless steel elements.
Hard, rough cloth.
It is recommended to us moist cloth and neutral cleaning agents.

ALTERNATE INSPECTION

Besides the current maintenance the user is dutybound to the following actions:

Alternate check and maintenance of cooker hood elements and assemblies,
Let the cooker hood be checked by the customer service after expiration of the warranty once in two years.
Abolishment of noticed errors,

Note! All installing and maintenance actions mentioned on the top as well as reparations are to be accomplished by a authorized installer.
Important! The user is responsible for the irreproachable condition and professional use of the unit. If the customer service is called because of an operating mistake, the visit is liable to pay costs in the warranty, too.
Damages, which are caused through not following this

RESPECT FOR THE ENVIRONMENT

The documentation provided with this oven has been printed on chlorine free bleached paper or recycled paper to show respect for the environment.
The packaging has also been designed to avoid environmental impact. Packaging material is ecological and can be re-used or recycled.
By recycling the packaging, you will help save raw materials as well as reducing the bulk of domestic and industrial waste.

Disposing of the packaging
Please dispose of the packaging that came with your appliance in an environmentally friendly way.
Recycling in this way saves on resources and cuts down on waste.

Disposing of old appliances
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

WARRANTY CONDITIONS FOR HOME APPLIANCES

The warranty for a broken part is valid for the full period of 24 months from the day of purchase.
The manufacturer only covers the servicing in the event of a manufacturer fault, such as but not limited to: inappropriate design, installation by technician, defective materials.
This warranty applies only to products used for the following purposes: non-commercial, personal, family, residential, or household. For anything outside of these purposes, the warranty is only valid for 4 months from the date of purchase of the products.
Repairs that qualify under this warranty guarantee are completely free including the cost of labour, and materials, transportation is determined by the relevant Kaiser servicing centre.
Any questions or queries on the quality of the product will be assessed only after our servicing company checks the product. Any conclusions will only be reached based on the outcome of a servicing report.
The product will only be exchanged within the warranty period in the situation that the servicing expert concludes that the product cannot be repaired or if the same product requires parts changed three times in total within the warranty period.
In case of unnecessary or unjustiﬁed demands for customer service, we charge for our service the usual time consumption and transportation fees. Before you contact our customer service , please check whether it‘s a defect or error of a product or or mistake of maintenance. Please take the time to communicate with the relevant Kaiser service center.
Installation of the device should only be carried out by qualiﬁed professional persons. The customer is required to provide appropriate justiﬁcation. Otherwise there is no entitlement to the grant of a guarantee.
Only the distributor selling the products has the right to exchange the defected product for a new one.
Liability under this warranty is limited to, unless otherwise speciﬁed by law is all referred to these above obligations.

WARRANTY NOT VALID WHEN:

In the event of our products being damaged or experiencing some kind of fault from transport damage, due to incorrect installation by other than trained Kaiser technician or taking improper care of the products, connecting to the wrong power supply, the use of non-recommended cleaning agents and detergents. Any failure to comply with the instructions for operational use or if the product has been repaired or modiﬁed or installed by the customer and changed or removed the serial number will not qualify for the warranty conditions.
Products being serviced by an unauthorized servicing company will not be valid for warranty.
Product failures caused by reasons independent of the manufacturer, such as ﬂuctuations in the power supply, external events such as nature or natural disasters, ﬁre, insects or domestic and wild animals will not comply with the warranty conditions.
If the glass or the ceramic glass on a product is broken or defected after installation, the customer will be held liable.
Any damage scratches, cracks, and external mechanical faults caused during the operation by the customer.
The damage of certain parts being caused by normal wear and tear such as (lamps, ﬁlters, etc.).
Other external factors causing damage such as adjusting the products and cleaning.
Any other damage caused by the fault of the user and which is not linked to faults caused by the manufacturer will not comply with the warranty agreement.

The unearthed devices are potentially dangerous.
The manufacturer accepts no liability for damages which have caused by improper use, the incorrect installation, operation, application or maintenance.

WARRANTY CARD

(Nr. indicates the number of the unit, see the back cover of this manual)
This warranty does not limit statutory rights of consumers
Congratulations on the purchase of household appliances of excellent quality!
Please refer to the warranty card and make sure it has been properly filled in and had a shop stamp. In the absence of the stamp and the date of purchase, warranty period commences from the date of manufacturing of the product. Carefully check the appearance of the product, all claims about the product appearance must be notified to the seller at the time of purchasing.
Keep the warranty certificate and the receipt. In the event of the product components incomplete/ missing and or requirement for their replacement, please contact your dealer.
For the installation, connection and all matters relating to the maintenance, contact authorized service centres. Details of authorized service and repair service centres are attached in a separate list.
We reserve the right to make changes in design or manufacturing technology. Those changes do not entail obligation to update or improve the previously released products.

EG Declaration of Conformity
Manufacturer:OLAN-Haushaltsgeräte e.K.
Address:Eichborndamm 277 13437 Berlin Germany
This is to confirm that all cooker hoods

Marke / Brand :
Typ/ Type:
A 63…, A 93… …
= Laufnummer des Modelles / model number

= Farbe / colour
comply with the regulations of the European Directives.
The conformity of the designated product with:
- the regulations of the European Directives 2014/35/EU: LVD (Low Voltage Directive) and CE 2014/30/EU: EMC (Electromagnetic Compatibility);
- Commission Regulation (EU) No 65/2014 of 1. October 2013 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to the energy labelling of domestic ovens and range hoods;
- Commission Regulation (EU) No 66/2014 of 14. January 2014 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for domestic ovens, hobs and range hoods;

is demonstrated by full compliance with the following European standards:

DIN EN 62233:2008
DIN EN 60335-2-31:2014
DIN EN 60335-1:2012+AC:2014+A11:2014
Berlin, 12.11.2021
N. Liskovoj
Abteilungsleiter/ Department Manager

Reduction of environmental impact

Information on reducing the environmental impact from cooking and non- destructive disassembly.
The following calculation and measurement methods were used to determine the results and in accordance with the requirements for labeling in terms of energy consumption and in terms of ecodesign requirements: Directives of the European Parliament and of the Council – Regulation (EU) No. 65/2014 and No. 66/2014.
EN 50564:2011 – Electrical and electronic household and office equipment – Measurement of low power consumption.
Information on reducing the environmental impact (e.g. energy consumption) from cooking in accordance with Annex I, No. 2 of Regulation (EU) No. 66/2014 with a regard to setting ecodesign requirements for household ovens, hobs and cooker hoods.

Use baking pans and trays with dark and matte surfaces, because they conduct heat better
Open the oven door during cooking only when necessary
Preheat the cooking chamber only when necessary according to the recipe
Always select the lowest recommended temperature for cooking temperatures
Switch the oven to minimum temperature shortly before the end of the cooking time to use the residual heat
To ensure energy efficiency, switch all buttons (temperature, interior light and program) to “0/Off” when the oven is not in use
Remove any soiling immediately, otherwise the cleaning effort may increase
Use biological cleaners to clean the oven

Information for professional users for dismantling according to Annex I, No. 2 of Regulation (EU) No. 66/2014
Information on non-destructive disassembly for maintenance purposes

Disassembly for maintenance purposes can only be performed for the oven door (see chapter “Disassembling the oven door” p.71).
Disassembly for maintenance purposes is not foreseen.
For repair and replacement of defective parts, please contact the customer service.
Accumulators are not included.

Disassembly information related to recycling, recovery and disposal at the end of the life of the device.

Dismantling of devices with gas connection may only be carried out by a licensed gas and water installer.
Dismantling of devices with electrical connection should be performed by a licensed electrician.

For recycling and resource recovery, specify the device:

municipal collection point run by the public waste disposal authorities
manufacturer’s own waste disposal company that offers a take-back system
local electrical retailer who voluntarily takes back electrical equipment.

For information on the energy efficiency index for each oven compartment, the dimensions of the appliance, the number of oven compartments, the heat source per oven compartment and the volume per oven compartment please refer to the data sheet, attached to the user manual.

The manufacturer declines all responsibility for possible mistakes and typing errors and reserves the right to make in design and construction of our own products those changes which do not touch negative influence upon the qualities and properties without a preliminary notification.

OLAN-Haushaltsgeräte • Berlin • Germany
www.kaiser-olan.de