ADYSS A100 Mobile Phone Follow-Up Mount Tripod Instructions
- June 12, 2024
- ADYSS
Table of Contents
A100 INSTRUCTIONS
Welcome to the mobile phone follow-up mount !
- Mobile phone clip
- Fill light
- Follow the camera
- Follow indicator
- Switch push
- Aluminum alloy telescopic rod
- Panorama key
- Right-click
- Capture key
- Left
- Charging port
- Sliding sleeve
- Support foot
- Non slip foot pad
Product operation steps
The angle can be adjusted up and down, after the angle adjustment is completed Fixed position.
First pull the tripod outward from the bottom.
Open the tripod outward.
Press and hold the sliding sleeve and pull it down until the end is fully deployed. When retracting, press and hold the sliding sleeve to retract the bracket.
Stretch the bracket as appropriate, extend the bottom Support area, increase anti-dumping ability.
Pull the telescopic arm to the required length.
Pull the phone clip open, put the phone in and clamp it.
Push the push button up to turn on the follow-up function.
The LED changes from a flashing green state to an indication ,When the light is green and solid, the face detection is set successfully.
Remote control for panoramic rotation, steering control, Take photos remotely.
Overhead shooting mode
Follow up :
In the state of turning on, people are video graphing ,Set the OK gesture
within the head range for 2 seconds . After the excitation tracking is turned
on, the hand is placed Excitation tracking stops after palm 2S; not People are
within range of the camera for 15 minutes Automatic shutdown after that;
Operating instructions of Bluetooth remote controller
- type-c Charging port
- Left
- Panorama key
- Right-click
- Capture key
- remote control switch
1. Turn the side switch of the remote controller ( ON / OFF), and the
indicator light of the remote controller will flash automatically.
2. Turn on “Settings” – “Bluetooth” of the mobile phone, turn on Bluetooth,
search for “ADYSS-A6”, click the device name pairing, display “connected”, the
indicator stops flashing, that is, the connection is successful (the remote
controller is turned on).
3. Panorama key: Click the “Panorama Button” after the phone clip rotates
once, then click Stop Rotation, and long press “Panorama Press key” to enter
loop mode and turn all the way.
4. Left button: long press the left button to make the mobile phone clip turn
clockwise, and stop rotating when released; Short press is not functional.
5. Right button: long press the right button to make the mobile phone clip
turn counterclockwise, and stop rotating when released; Short press is not
functional.
6. Shooting button: Press the shooting button to take pictures when connected
to the mobile phone.
Special note: (when Apple IOS system setting and shooting key 2 are invalid, the setting method is as follows)
- Apple IOS 13.4 above setting method: A. Mobile phone Bluetooth on the remote control link B. the screen automatically rotates and locks C. turn on settings – auxiliary functions – touch auxiliary touch – turn on D. the above systems need to be calibrated for the first time. Find the tracking sensitivity of the auxiliary touch and move the dot to the left and then back to the default position.
- Method of adjusting shutter key position when shooting key 2 is invalid: A. Enter the software photographing interface B. press the photographing key 2 for a long time without letting go C. at the same time, press the direction key for a short time to move the “pointer / dot” to the range of the photographing software shutter circle.
Product parameters
Product model: A100
Maximum bearing capacity: 500g
Working voltage : 3.6~4.2V
Main material : Aluminum alloy & ABS plastic
Operating temperature : -10°~40°
Support system : Android, IOS, Hongmeng
Charging voltage : DC 5V
Maximum stretching distance: 100mm
Remote control battery capacity: 55mA
Folding size : 3870265mm
Standby time of remote control: 30day
Matters needing attention
- Please store it carefully to avoid pinching your hands.
- Before use, please confirm the places with geographical and facility restrictions, and prohibit acts against public order.
- Do not place the product on high places, uneven countertops and floors to prevent falling damage.
- Do not use the power supply exceeding the load of the product, which will cause the product to heat up and the circuit board to burn out.
- Do not disassemble or modify this product by yourself.
- Do not hit or throw this product, which may cause internal failure.
- Do not put the product in a low temperature and humid place.
- Do not throw the product into the fire and keep away from the fire source.
- Warning: This product is not suitable for children under 3 years old to operate alone.
WARRANTY CARD
Product model : Place of purchase :
Date of purchase : Order number :
Customer name : Warranty content :
Contact address :
One year limited warranty summary
Our company guarantees that the attached hardware products are free from defects in materials and workmanship within one year from the date of original retail purchase, and can accept after-sales problems. Our company does not guarantee normal wear and tear, nor does it guarantee damage caused by accident or abuse. To obtain the service, you can visit the retail store owned by Our company or the authorized service provider of Our company to repair and replace your products at your discretion. Your warranty rights are in addition to the rights provided by local consumer law. When you file a claim under this warranty policy, you may need to provide details of the proof of purchase.
MADE IN CHINA
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
RF waning for Potable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.