Blusafe Contour V Smart Lock 3 in 1 Camera Doorbell Fingerprint Keyless Entry Door Lock Instruction Manual

June 12, 2024
Blusafe

Contour V Smart Lock 3 in 1 Camera Doorbell Fingerprint Keyless Entry

Door Lock

Product Information

The Blusafe Contour / Contour V is a smart lock that provides
secure access to your door. It comes with various features,
including a fingerprint sensor keypad and a built-in camera
(available only in Contour V). The package includes all the
necessary components for installation, such as the internal panel,
external panel, mounting plate, latch, strike plate, strike box,
screws, screwdriver, keys, and keycards.

Product Usage Instructions

Tools Required

  • Pliers
  • Hammer
  • Chisel
  • Tape Measure
  • Pencil
  • Drill Bits
  • Drill
  • Screwdriver

Latch Installation Guide

The latch installation guide is applicable for new doors that do
not have pre-existing holes for the lock or latch. If your door
already has the required holes, you may skip these steps.

  1. 1. Measure and mark the height of the holes on the door using the  

    template guide. The suggested height for the hole centerline is 38
    or 970mm from the base of the door.

  2. Drill a 2-1/8 (54mm) hole and a 2/5 (10mm) hole on the marked
    positions.

Note: It is recommended to drill both holes for
the best installation of the lock. If you choose not to drill the
2/5 (10mm) hole, the C Screw Pillar will not be used in the
installation of the Contour Smart Lock.

Install the Latch:

  1. Adjust the latch length according to the backset (2-3/8 (60mm)
    or 2-3/4 (70mm)).

  2. Fix two self-tapping screws onto the latch plate using a
    screwdriver.

Install Strike Plate and Box:

  1. Extend the latch out and gently close it against the door
    frame. Mark the top and bottom of the latch on the frame.

  2. Mark a centerline down the jamb for the strike plate, ensuring
    enough space for the door to close against the stop.

  3. Place the strike plate on the jamb, aligning the marks from the
    latch to the hole for the bolt. Also, ensure that the strike plate
    is centered on the marked centerline.

  4. Scribe around the outer edge of the strike plate with a pencil
    and chisel within the scribed area to a depth of 1/12 (2mm).

  5. Chisel out the hole to a depth of 1 (25mm) to allow the latch
    to extend and move freely.

  6. Insert the strike box and strike plate into the hole, then
    screw in the strike plate as shown.

Once the latch and strike plate are installed, you can proceed
with the remaining installation steps as mentioned in the user
manual.

Blusafe Contour / Contour V

Installation Manual

v1.0

Please scan the QR to get newest manuals on Blusafe Products
1P

Installation Manual Contents

0. Tools Required

P0

1. Package Contents

P1

2. Latch Installation Guide

P2

3. Blusafe Contour Smart Lock

P4

4. Determine Handle Direction

P5

5. Change External Handle Direction

P6

6. Change Internal Handle Direction

P7

7. Installation of Blusafe Contour Smart Lock

P8

Tools Required

Pliers

Hammer

Chisel

Tape Measure

Pencil

Drill Bits

Drill

Screwdriver

P2

1. Package Contents P1

Package Contents

Internal Panel

Mounting plate

External Panel

A – ST 3.9 x 20mm Self Tapping Screw x 4

B1- M4 x 35mm Screw x 4

B2- M4 x 50mm Screw x 4

C – Screw Pillar x 1

D – ST 3.9 x 16mm Self Tapping Screw x 1

E- Screwdriver x 1

F- Key x 3

G – Keycard x 2

H- M4 x 10mm Screw x 4

Strike Plate

Strike Box

Latch
1P

2. Latch Installation Guide P2 – P3

10.6070.5525 Latch Installation Guide
The below latch installation guide is meant for new doors that do not already have holes for the lock or latch. If your door already has the required holes to install the latch and lock, you may skip the below steps and proceed to P04.

Drill Lockset and Latch Holes

1-2/5″ to 2-1/8″ 35mm to 54mm

The Contour handle is suitable to use on door thickness between 1-2/5″ and 2-1/8″(35 and 54mm).

2/5″ 10mm 2-3/8″or 2-3/4″ 60 or 70 mm
2-1/8″ 54mm
1″ 25mm
1″ 26mm
P2

4-3/4″ 121mm

2-5/16″ 58mm

Use the template guide to mark the holes on door at required heights (suggested height for 54mm hole centreline is 38″ or 970mm from the base of door). Drill out a 2-1/8″ (54mm) and a 2/5″ (10mm) hole.
Note
It is suggested to drill both holes on door in order to have best installation of the lock afterwards. If you choose not to drill the 2/5″ (10mm) hole, the C Screw Pillar will not be used in the “Installation of Contour Smart Lock”.
Fold the template guide along the edge of the door and position it over the 2 ” (54mm) diameter hole. Mark the 1″ (25mm) diameter hole on the edge of the door for the latch. Drill out the 1″ (25mm) diameter latch hole. Chisel out the remainder of the slot on the edge of the door to accept the latch body. This is a rectangle 1″ x 2¼” (26mm x 58mm) as shown above. The depth should be ” (3mm) to accept the latch body. Please test fit the latch body to ensure a good fit before installing.

2. Latch Installation Guide P2 – P3

Latch Installation Guide
Install the Latch
Adjust the latch length according to backset (2-3/8″ (60mm) or 2-3/4″ (70mm)). Fix two self tapping screws onto the latch plate.

Screwdriver

A × 2

2-3/8″ (60mm)

2-3/4″ (70mm)

Install Strike Plate and Box

2-3/4″(71mm) 1-1/8″(29mm) 1-3/8″(36mm)

15/16″(24mm) 1-1/8″(29mm)

Strike Box Strike Plate

A × 2

With the latch installed, extend the latch out and gently close against the door frame. Mark on the frame the top and bottom of the latch.
Mark a centre line down the jamb for the strike plate. Ensure this centreline allows door enough space to close against the stop.
Place the strike plate on the jamb aligning the marks from the latch to the hole for the bolt. Also ensure the strike plate is centred on the centreline marked. Scribe around the outer edge of the strike plate with a pencil and chisel within the scribed area to a depth of 1/12″(2mm).
Fit the strike plate into recessed hole and mark the hole for latch.
Chisel the hole out to a depth of 1″(25mm) to allow the latch extend and move freely.
Insert the strike box and strike plate into the hole. Screw in the strike plate as shown.

3P

3. Blusafe Contour Smart Lock P4

Blusafe Contour Smart Lock

Battery Cover Internal Panel Internal Handle

External Panel Camera
Only available in Contour V Fingerprint Sensor Keypad
Key Card Area Cylinder Cover External Handle
Mechanical Key hole Micro USB

Louderspeaker Hole

P4

4. Determine Handle Direction P5

Determine Handle Direction
Depending on which way your door opens, determine which way the handles need to face. The handles should always point towards the door hinges. Check the Contour/ Contour V handles against the current handles. If the handles need to face the other way, please see next page.
5P

Change External Handle Direction
Screwdriver

5. Change External Handle Direction P6

1.Rotate the handle and the spindle by 45 degrees to expose the set screw.
3. Rotate the handle downwards from its horizontal position, by 225 degrees.
P6

2. Unwind the set screw.
screw hole
4. Rotate the spindle downwards by 45 degrees until seeing the screw hole. Locate and fasten the set screw.

Change Internal Handle Direction
Screwdriver

6. Change Internal Handle Direction P7

1.Unwind the set screw.

2.Rotate the handle downwards by 180 degrees.

3. Locate and fasten the set screw.
7P

Installation of Blusafe Contour Smart Lock

Tape Measure

Boor Thickness/mm
1-²/” to 1-/” (35-45mm) 1-/” to 2-¹/” (45-54mm)

Screw B Length
M4×35mm M4×50mm

7. Installation of Blusafe Contour Smart Lock P8 – P16

Select the fixing screw of appropriate length according to the door thickness.
Please make sure the latch is installed properly as per the “Latch Installation Guide” prior to the following installation steps: Measure the door thickness. Please select the appropriate screws based on the door thickness. You can refer
to the above table for reference.
P8

Installation of Blusafe Contour Smart Lock

Pliers

C × 1

Tip
Please peel off the skin and use the 3M tape at the back of external panel to reinforce the mounting.

Warning!
The C Screw Pillar must be used if the smart lock is exposed to rain, to ensure the best installation and weather seal.

7. Installation of Blusafe Contour Smart Lock P8 – P16

Make sure the cable is pulled through the bottom of hole.
Tighten the C Screw Pillar onto the back of the external panel. Pull the cable of the external panel through the bottom of the hole. Insert the
spindle through the spindle hole of the latch. Push the external panel carefully into the door, and make sure the C Screw Pillar feed through the upper hole of the door.
Tip Please use the 3M tape at the back of external panel to reinforce the mounting.
9P

7. Installation of Blusafe Contour Smart Lock P8 – P16

Installation of Blusafe Contour Smart Lock
Make sure the cable is pulled through the bottom of hole. Pull the cable through the slot of the mounting plate.
P10

Installation of Blusafe Contour Smart Lock

Screwdriver

B × 1

or

B × 3

D × 1

Alternative
If you used the 3M glue only and not the C Screw Pillar on external panel, please use the ST3.9x16mm self-tapping screw D instead of the B Screw at the top.

B Screw or D Screw B Screw × 3

7. Installation of Blusafe Contour Smart Lock P8 – P16

Drive the screws in but do NOT tighten them all the way. Adjust the external panel to the correct position and then proceed to tighten the screws.
11P

7. Installation of Blusafe Contour Smart Lock P8 – P16

Installation of Blusafe Contour Smart Lock
E × 1
Unwind the battery cover screw with E Screwdriver provided, take off the battery cover.
P12

7. Installation of Blusafe Contour Smart Lock P8 – P16

Installation of Blusafe Contour Smart Lock
The cable MUST be pulled through this slot. Connect the external and internal cables together.
13P

Installation of Blusafe Contour Smart Lock

Screwdriver

H × 4

7. Installation of Blusafe Contour Smart Lock P8 – P16

Buckle the internal plate onto the mounting plate. Fix the H Screws with a screwdriver.
P14

7. Installation of Blusafe Contour Smart Lock P8 – P16

Installation of Blusafe Contour Smart Lock
Ensure the batteries are inserted correctly.
Rotate the handle to ensure the latch can be extended and retracted freely.Stand inside, close the door and repeat the rotation of handle. Ensure the latch can still be extended and retracted freely. If not, you may need to adjust the positioning of the latch in the door.
Open the battery cassette. Insert 8 AA batteries as shown above. Note For the best experience possible, please use high quality AA batteries in your Smart Lock. The batteries will last for 6-8 months depending on usage and environment; however, recommend you change the batteries every six months or when notified to do so in your App.
15P

7. Installation of Blusafe Contour Smart Lock P8 – P16

Installation of Blusafe Contour Smart Lock
E × 1
Put on the battery cover, fix the screw with the E Screwdriver.
P16

Security at your fingertips —- Blusafe 17P

P18

Please scan the QR to get newest manuals on Blusafe Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals