Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock Installation Guide

June 12, 2024
Blusafe

Blusafe Contour / Contour V
Installation Manual
v1.1

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock

Tools Required

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
1

Package Contents

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
2

10.6070.5525

Latch Installation Guide

The following latch installation guide is designed for new doors that do not already have holes for the lock or latch. If your door already has the required holes to install the latch and lock, you may skip the steps below and continue to P04.
Drill Lockset and Latch Holes

① The Contour handle is suitable to use on door thickness between 1-2/5″ and 2-1/8″(35 and 54mm).

② Use the template guide to mark the holes in door at required heights (suggested height for Φ 54mm hole centreline is 38″ or 970mm from the base of door). Drill out a 2-1/8″ (Φ54mm) and a 2/5″ (Φ10mm) hole.
Note
It is suggested to drill both holes in door in order to have a better installation of the lock. If you choose not to drill the 2/5″ (Φ10mm) hole, the C Screw Pillar will not be used in the “Installation of Contour Smart Lock”.

③ Fold the template guide along the edge of the door and splace it over the 2 ⅛ ” (54mm) diameter hole. Mark the 1″ (25mm) diameter hole in the edge of the door for the latch. Drill out the 1″ (25mm) diameter latch hole. Chisel out the remainder of the slot on the edge of the door to accept the latch body. This is a rectangle 1″ x 2¼” (26mm x 58mm) as shown above. The depth must be ⅛ ” (3mm) to accept the latch body. Please test the fit of the latch body to ensure a good fit before installing.

Install the Latch
Adjust the length of the latch according to backset (2-3/8″ (60mm) or 2-3/4″(70mm)). Fix two self-tapping screws to the latch plate.

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
6

Install Strike Plate and Box

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
7| Blusafe Contour 3 in 1 Smart
Keyless Entry Door Lock - Fig 8
---|---

① With the latch installed, extend it and gently close it against the door frame. Mark on the frame the top and bottom of the latch.
② Mark a centre line on the jamb for the strike plate. Ensure this centre line allows the door enough space to close against the stop.
③ Place the strike plate on the jamb aligning the marks from the latch to the bolt hole. Also ensure the strike plate is centred on the marked centerline. Scribe around the outer edge of the strike plate with a pencil and chisel within the scribed area to a depth of 1/12″(2mm).
④ Place the strike plate in the recessed hole and mark the hole for the latch.
⑤ Chisel the hole out to a depth of 1″(25mm) to allow the latch to extend and move freely.
⑥ Insert the strike box and strike plate into the hole. Screw in the strike plate as shown.

Blusafe Contour Smart Lock

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
9

Determine Handle Direction

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
10

Depending on which way your door opens, determine which way the handles need to face.

The handles should always point towards the door hinges. Check the Contour/Contour V handles against the current handles.

If the handles need to face the other way, please see next page.

Change External Handle Direction

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
11

Change Internal Handle Direction

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
12

Installation of Blusafe Contour Smart Lock

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
13

Please make sure the latch is installed properly as per the “Latch Installation Guide” prior to the following installation steps:
① Measure the thickness of the door.
② Please select the appropriate screws based on the door thickness. You can refer to the above table for reference.
Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
14③ Tighten the C Screw Pillar on the back of the external panel.
④ Pass the external panel cable through the bottom of the hole. Insert the spindle through the spindle hole of the latch. Carefully push the outer panel towards the door, and make sure the C Screw Pillar feed through the upper hole of the door.

Tip
Please use the 3M tape at the back of external panel to reinforce the mounting.

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
15

⑤ Pull the cable through the slot of the mounting plate.

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
16

⑥ Insert the screws, but DO NOT fully tighten them. Adjust the external panel to the correct position and then proceed to tighten the screws.

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
17

⑦ Unwind the battery cover screw with the E Screwdriver provided, remove the battery cover.

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
18

⑧ Connect the external and internal cables together.
Warning!
Please make sure the cables are connected in the correct orientation otherwise will cause permanent damage to the lock!

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
19

⑨ Buckle the internal plate onto the mounting plate. Fix the H Screws with a screwdriver.
Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
20⑩ Rotate the handle to ensure the latch can be extended and retracted freely. Stand inside, close the door and repeat the rotation of the handle. Ensure the latch can still be extended and retracted freely. If not, you may need to adjust the positioning of the latch on the door.
⑪ Open the battery cassette. Insert 8 AA batteries as shown above.

Note
For the best possible experience, please use high quality AA batteries in your Smart Lock.
The batteries will last 6-8 months depending on usage and environment; however, we recommend that you change the batteries every six months or when notified in your App.

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
21

⑫ Put on the battery cover, fix the screw with the E Screwdriver.

Security at your fingertips —— Blusafe

Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock - Fig
22

Please scan the QR to get the newest manuals on Blusafe Products

https://blusafesolutions.com/download- manuals/

Documents / Resources

| Blusafe Contour 3 in 1 Smart Keyless Entry Door Lock [pdf] Installation Guide
Contour, Contour 3 in 1 Smart Keyless Entry Door Lock, 3 in 1 Smart Keyless Entry Door Lock, Smart Keyless Entry Door Lock, Keyless Entry Door Lock, Entry Door Lock, Door Lock
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals