ELENOS Q7 Wireless Neckband Earphones User Manual
- June 12, 2024
- ELENOS
Table of Contents
Summary of button functions
- Power On! Power OffNolume up/Next song
- Volume down/Previous song
- Magnetic charging port
- LED indicator
- Multifunctional buttons: Pause/ Play/ Answer Phone Call! End Phone Call/Voice Assistant
- Microphone
Controls
On: When the headphone is in power-off state, press and hold power button
for 3 seconds with blue LED flickering, reminding tone: power on.
Off: When the headphone is in power-on state, press and hold power button
for 5 seconds with red LED flickering once, reminding tone: power off.
Connect BT: When the headphone is in power-off state, press and hold it
for 3 seconds to enter a pairing state with red and blue LEDs flickering and
reminding tone: pairing. After the device (smart phone, tablet computer, etc.)
discovers VT. press it to connect. Connected successfully: When the
headphone Is successfully linked to the device, blue LED will flicker every 5
seconds with reminding tone:
Connected Pause/play: In the BT connection music playback state, click
the multi-function button to pause, and then click the multi-function button
to play;
Answer/hang up: In the incoming call state: click the multi-function
button to answer, long press the multi-function button for 2 seconds to reject
the call. In the call state, click the multi-function button to hang up
Vol.’. Press the Vol+ once to turn up the volume.
Vol-: Press the Vol- once to turn down the volume. The next song: Long
press “V+’ for 2 seconds when music is playing In a song: Long press*V– for 2
seconds when music is playing Voice assistant: Keep FIT link, and double-click
the multi-function button to turn on the voice assistant, then double-click it
again to exit. Reset: After plugging the charging line, the headphone will be
reset and powered off for charging.
Clear pairing information: Press the power button and the volume off
button for 5 seconds to clear the pairing information in shutdown mode, Red
and Blue light blinks 1 second spontaneously
Charging: in case of using charging line for charging, connect the
headphone with the USB power. During the charging, LED turns red. After
charging, the LED turns blue.
How to wear Hang the headphone behind your neck with both speakers
clinging to your cheekbones. After that, a-djust it until you feel
comfortable.
Specifications
Music play time ———————-8 hours(70% volume)
Standby time ———————–20 days
Charging time ————————2 hours
BT version —————————-5.3
Speaker impedance————————– 160±15%
Microphone sensitivity ——————————42±3db
Product weight —————————-279±2g
Connection distance ———————————————-15 meters
Charging voltage/current———————————–5V/0.5A
Attentions
- Pleaes wear the speakers of the headphone at your cheekbones before your ears and do not put them In your ears.
- Listening to music for an excessive long time mayake you feel uncomfortable, please try to use a medium volume instead of a big one.
- No matter how the volume is, please do not make it prevent you from hearing the surrounding sounds. Please take care when using the headphone.
- Do not throw, press the headphone or put it in the water.
- The headphone should keep away from fire. water and high voltage devices.
- It is not for children’s use as it contains small parts.
- Please do not treat it as domestic waste. Instead, send it to your electrical and electronic recycling station. If there is any injury or property loss due to violation of the above contents, we will not bear any responsibility.
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>