Lindby LED Wall Lamp Instruction Manual
- June 12, 2024
- Lindby
Table of Contents
Lindby LED Wall Lamp
Product Information
- Revision: 2.4
- Languages: DE, EN, FR, NL
Installation instructions
This product is used for lighting. It should be installed, operated, and maintained in compliance with national installation and safety regulations. Always refer to the symbols on the packaging and in the installation instructions for safety instructions. The light should not be worked on if a voltage is applied to avoid the risk of electric shock. The product and its packaging contain small parts that can be swallowed by children, so keep children away from them. Technical knowledge corresponding to that of a person who has completed training in the electrical trade is assumed for these instructions. The electricity supply should only be connected by a trained electrician. Damaged electrical cables should be replaced by a trained electrician. Light sources should not be replaced by the user. The lights are not suitable for covering with thermal insulation materials or direct installation on normally flammable surfaces. Any use other than lighting can damage the product and cause hazards such as short-circuits, electric shocks, or fires.
Before using for the first time / Liability notice
Dear Customer,
Unpack the product carefully and check that it is complete and intact. The
light should not be used if there is any damage to the cable, glass or
electrical parts. In such a case, contact the service address named below
immediately.
Read through these instructions carefully. This will help you to avoid errors,
which could lead to a hazard or malfunction. Keep the instructions in case you
have any questions later. Pass on the instructions to each subsequent owner or
user of the product. Ensure that any supplement to the instructions is
enclosed.
The manufacturer cannot be made responsible and/or liable for personal
injuries or damage to property caused by:
- incorrect installation
- changes made to the product
- improper use (misuse)
- failure to obeserve these instructions
Health and safety regulations
Comply with the national installation and safety regulations for the installation, operation and maintenance. Always note the symbols on the packaging and in these installation instructions. Refer to the following list for the precise meanings of the symbols:
Disposal Instructions
Follow the provided disposal instructions for proper disposal of the product.
- Never work on the light if a voltage is applied. Warning – Danger of death! Always follow the general safety instructions and warnings.
- This product and its packaging contain small parts, which can be swallowed by children. Keep children away from the product and packaging!
- These instructions assume technical knowledge corresponding to that of a person who has successfully completed training in the electrical trade. The electricity supply should only be connected by a trained electrician Have damaged electrical cables replaced by a trained electrician only.
Caution: Risk of electric shock.
Note: On light sources, which are not intended to be replaced by the user.
Notes on the installation sketch
- The smallest distance to illuminated areas (in m).
- The lights are not suitable for covering with thermal insulation materials.
- The lights are not suitable for direct installation on normally flammable surfaces (only suitable for installation on non-combustible surfaces).
Intended use / foreseeable misuse
This product is used for lighting. Further information on the intended use is given on the installation sketch p. 9. Do not expose the light to large mechanical loads or stresses or heavy soiling. For safety reasons, you should not change and/or modify the product. Any use other than that described above can damage the product. This can cause hazards such as a short-circuit, electric shock or fire.
Cleaning/maintenance
The light should always be cooled and disconnected from the power supply before cleaning/ maintenance work is carried out! Check that no voltage is present. For regular cleaning, use a dry or lightly moistened cloth and never use chemicals or abrasive cleaner/scouring agent.
Notes on disposal
This light should not be disposed of in normal household waste. It should be handed in to a collection point for the recycling of large electrical and electronic appliances. Please find out about the relevant provisions regarding the separate collection of waste electrical and electronic equipment (WEEE) in your country. Correct disposal of your waste equipment protects the environment and people against potential negative consequences.
Batteries do not belong in household waste! Used batteries must be handed in to the public collection points in your municipality or wherever batteries are sold.
Declaration of Conformity and Service address
The light is designed, produced, and tested in conformity with EN 60598 and
fulfils the fundamental safety requirements of the EU Directives 2014/35/EU
and 2014/30/EU. The complete declaration of conformity is available at the
service address named in the following:
LUQOM Holding GmbH, Seelbüde 13, D-36110 Schlitz
020 3514 3658 info@luqom.eu
Subject to change without notice
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>