MAXHUB SI04B WiFi Module User Manual
- June 12, 2024
- MAXHUB
Table of Contents
SI04B WIFI Module
User Manual
Note: All the pictures in this manual are for reference only, subject to
our available products.
WIFI Module User Manual
Statement
- Intellectual property right statement: The hardware design and software of this product are covered by the patents. Anyone who reproduces this product or the content of the instruction without the authorization of the Company shall assume legal liabilities.
- This manual is for reference only, and the actual function of the final product is subject to the actual function of the product received by the customer.
- The picture is for reference only, please refer to the actual product. The company reserves the right to improve and change the appearance and design of the product without notice.
Safety Warning
- Before using and operating this device, please read thoroughly and comply with the following precautions in order to prevent accidents or inaccurate operations.
- DO NOT charge or use the device in dusty or wet conditions, to prevent internal circuit failure.
- Keep the device away from heat sources such as an electric heater.
- The product and accessories may contain some small-part. Please place them beyond the reach of children in avoidance of swallowing danger.
- The product is not waterproof, please keep it dry.
- Normal operating temperature is 0-40t, normal operating humidity is 10%-90°/0RH.
- Please contact professional service personnel for maintenance services.
- DO NOT insert any sharp or pointed object into the device.
- Prevent the device from falls and collisions with other objects, which may cause damages.
Installation Procedure
Warning: Please make sure the power cord of the Interactive Intelligent
Panel is disconnected before installation.
Step 1: Tear off the patch. Use a Phillips screwdriver to loosen two screws
and remove the cover.
Step 2 : Insert the module upward into the platform of Interactive Intelligent
Panel in the direction of the arrow.
Step 3 : Complete the connection.
Note: This Wi-Fi module only works for the Interactive Intelligent Panel
by plugging it into the above slot.
Software Function
- After installation, open the Interactive Flat Panel and the wireless module will run automatically.
- Click on Settings, on the menu.
- Click on “Wireless Network” and you can turn the wireless network on / off.
- Click on the “ ” icon to enter the wireless hotspot.
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and any part of your body.
♦ Non-modification Statement:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
♦ IC audiation Exposure Statement for Canada
This device contains licensee-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two
conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with ISED RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and any part of
your body.
The device for operation in the band 5150 5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems
This symbol, affixed to the product or its packaging, indicates that the
product must not be processed with household waste. It must be brought to an
electric and electronic waste collection point for recycling and disposal. By
the appropriate disposal of this product you also help in preventing
potentially negative consequences for the environment and human health. The
recycling of materials helps preserve our natural resources. For further
information regarding the recycling of this product, please contact your
municipality, local waste disposal center or the store where the product was
purchased.
https://drive.google.com/open?id=1jdLp7RvP3LfINPTeVTlmVbJkk1XfGrav
Call Center 1200 (Tsum)
The user manual applies to Model SIO4B.