Fovksuc U1-W Wireless Doorbell Kit User Manual
- June 12, 2024
- Fovksuc
Table of Contents
- Product Features
- Content
- Transmitter+1 Receiver
- What You Should Know Before Installation
- Product Structure Diagram
- Set UP and Operation
- Installation
- Battery Replacement of Push Button
- Chimes List
- Commom Problems and Troubleshooting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Fovksuc U1-W Wireless Doorbell Kit User Manual
Product Features
- Modern and stylish design
- 600 feet operating range(Over 1000 feet in open area)
- 600 selectable music/chime
- 5-level adjustable volume(Minimum to mute)
- Easy o install and use Bionic comfortable but ion
- Easy mix and match with more receivers and transmitter
- Low power consumption Memory function
- Music chime scroll through function
Content
-
Doorbell
-
Push Button
-
Adhesive Sticker
-
Screws & Anchors
-
Kay
-
User Manual
Transmitter+1 Receiver
Two or more transmitters pair (up o 20 transmitters be supported by the same receiver)
What You Should Know Before Installation
- Test the operating range you desire. Choose an electric outlet at the height of 3.3 feet at least and plug in the receiver and take the button outside the door to test if it can work well within the range you have chosen.
- Set a desired music (different or same one) for transmitters before installation. For music setting, see Operating Instructions. Doorbells have been paired and set to a default chime (Ding Dong) before leaving factory.
- Please do not install transmitter on metal doors since it is hard for the signal to transmit.
- Please take out the battery insulating strip before using. **(As picture 1)
**
- Ensure all surfaces are clean by wiping the installation area with a clean cloth. Please note that the sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or rain will also affect the adhesion over a longer period of time.
Product Structure Diagram
AC Powered Receiver
Waterproof Transmitter
- Volume/SET button
- Previous button
- Next button
- LED light (Transmitter)
- Speaker
- Plug
- LED on the push button
Set UP and Operation
Press the push button to test whether it is paired with the doorbell. The doorbell LED indicator flashes and ring.If it does noses* Connect Push Button” on page 5
-
Adjust the Volume
There are § levels of volume of choosing. Find the Volume Control button ( ) on loft side of receiver. press this bunion repasted to get desired volume level, Minimum to mute. -
Music/Chimes Selection
There are 60 choices of music chimes. press short this button( ) on receiver to cycle through the different music/chimes. Long press this button( K4 Jor button( ) On receiver to Play The First 2 Seconds of Each Music I Chime. If you eke the current music/Chime, just press s ( KK or( 154 ) button
Note : doorbell has a smart memory function that can remember you last melody and volume level -
Pairing Transmitters and Setting Music/Chime
You can connect up to 20 Transmitters to your doorbell -
Plug in the receiver, press the or of the receiver to Select Music/Chime.
-
Pressing and holding the on the receiver for 5s, the receiver will LED indicator on, which means receiver get into pairing mode.
-
Press push button, the receiver will the bell rings with LED indicator flashes, is pairing ok
Note: pair and set only one transmitter at a time to avoid interference and ensure successful operation. It 10s without any operation, the doorbell will exit the pairing mode. After selecting the Music/Chime, press the transmitter will automatically switch to the current ringtone. For the last paired transmitter. -
For Pairing Additional Transmitters
and receivers Just repeat step 31-32-33 for each additional transmitter or receiver. (Choose a different Music/ Chime for the 2nd transmitter to distinguish front and rear doors)
Note: This method is suitable for multiple transmitters or multiple receiver pairing -
Reset (Clearing out Settings)
Hold down volume button( ) and plug it into an outlet, After playing the beep twice and LED indicator on, all settings will return to factory defaults.
Installation
Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to see and hear.
-
For Receiver:
Plug-in receiver: Just plug receiver into standard outlet in room. -
For Push button:
IMPORTANT: Before installation, please test if the operating range you choose is working and set music if needed. Before you drill any hole in the wall, please make sure there are not cables or pipes. To install you will require a drill and cross-head- ed screwdriver
Open the Transmitter with screw driver and separate the front cover from the
back cover. Penetrate the two standby holes at the back cover with two screws.
Then fix the screws on the wall at suitable height.
Or you can stick the Transmitter with the double-sided adhesive tape.
If you are not mounting the push button to the wall, place it where you want it.
Battery Replacement of Push Button
Open the battery cover and install the CR2032 battery.
Note: When you replace the battery with a new one, be carefull to put the positive terminal of the battery facing upwards.
Specifications
| Doorbell| Push Button
---|---|---
Operating Temperature| -4°F to140°F| -4°F to140°F
Radio Frequency| 433 MHz| 433 MHz
Range (open field)| 1,000 ft| 1,000 ft
Sound Level (typical)| 0-110 dB|
Battery Type| 1Plug-n AC10i250V| CR2032
Battery Life(5 activations/day)| Up to Syears| Up to 3 years
Rain Proof| N/A| IP55
Internal Sounds| 60 Melody| N/A
Type of Bulb| LED/Blue| LED/Blue
Chimes List
- Ding-dong, Ding-dong
- Ding-dong, Ding-dong
- Ding-dong, Ding-dong
- Corsica Doorbell
- Ding-dong
- Ding-dong Chime
- Hello Welcome(English)
- Westminster Chimes1
- Westminster Chimes2
- Big ben electronic doorbell 11-40. NEWAGE-01-NEWAGE-030
- Classical organ
- Morning 43.Dingdong merrily on high
- Waltz of the flowers
- For Alice
- The William tell overture
- The cuckoo waltzes
- Minuet in G
- Happy birthday
- Fantaisie Impromptu
- Yesterday Once More
- Clarinet Polka
- Russe Dance
- Souvenirs Denfance
- Jasmine Flower
- Waltzes Op.
- No.
- Hungarian Dance
- Spring Song
- Accordion Tango
- Alarm Sound Effect
Commom Problems and Troubleshooting
Receiver suddenly can’t get signal from transmitter and doesn’t ring
Reason| Solution
Low-power battery in transmitter.The less power in transmitter, the shorter
range is.| Replace with a new battery.
Reset the receiver by accident so that transmitter is not paired with receiver
any more.| Re-pair receiver with transmitter following the Operation
Instructions.
There’s rust on the battery contacts or button area on PCB board of
transmitter.| Remove the rust to see if it can re-work
Receiver keeps ringing continuously and LED indicator of transmitter stays
on.
Raindrops have gone inside transmitter, which causes the short circuit and let
transmitter keep transmitting signals.| Remove the battery and PCB board of
transmitter and then dry them with a hair dryer. Change the install location
of transmitter if necessary.
Customer Service
We hope you never have the need, but if you do, our service is friendly and hassle-free
30-day money-back guarantee
18-month warraniy
Lifetime ser support
: customerservice@fovksuc.com
: www.fovksuc.shop
: www.fovksuc.com
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
The devices has been evaluated to meet general RF exposure requirement, the device can be used in portable exposure condition without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>