FOVKSUC U2-W Wireless Doorbell Kit User Manual

: May 15, 2024
: Fovksuc

Table of Contents

Product Features
Contents
What You Should Know Before Installation
Product Structure Diagram
Set UP and Operation
Installation
Battery Replacement of Push Button
Specifications
Chimes List
Commom Problems and Troubleshooting
Customer Service
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Wireless Doorbell Kit
User Manual

Product Features

Modern and stylish design
600 feet operating range(Over 1000 feet in open area)
60 selectable music/chime
5-level adjustable volume(Minimum to mute)
Easy to install and use
Bionic comfortable button
Easy mix and match with more receivers and transmitter
Low power consumption
Memory function
Music/chime scroll through function

What You Should Know Before Installation

Test the operating range you desire. Choose an electric outlet at the height of 3.3 feet at least and plug in the receiver and take the button outside the door to test if it can work well within the range you have chosen.
Set a desired music (different or same one) for transmitters before installation. For music setting, see Operating Instructions.Doorbells have been paired and set to a default chime (Ding Dong) before leaving factory.
Please do not install transmitter on metal doors since it is hard for the signal to transmit.
Please take out the battery insulating strip before using. (As picture(1))
Ensure all surfaces are clean by wiping the installation area with a clean cloth. Please note that the sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or rain will also affect the adhesion over a longer period of time.

Product Structure Diagram

Volume/SET button
Previous button
Next button
LED light
Speaker
Plug
LED on the push button (Transmitter)
Mute the sound

Set UP and Operation

Press the push button to test whether it is paired with the doorbell. The doorbell LED indicator flashes and ring.If it does not,see”“Connect a Push Button” on page 5.

Adjust the Volume
There are 5 levels of volume for choosing.Find the Volume Control button( ) on left side of receiver.press this button repeatdly to get desired volume level,Minimum to mute.
Music/Chimes Selection
There are 60 choices of music/chimes.press short this button( ) on receiver to cycle through the different music/chimes.
Long press this button( )or button( ) On receiver to Play The First 2 Seconds of Each Music /Chime. If you like the current music/Chime, just press this ( ) or( ) button.
Note:doorbell has a smart memory function that can remember your last melody and volume level
Pairing Transmitters and Setting Music/Chime
You can connect up to 20 Transmitters to your doorbell.
Plug in the receiver, press the or of the receiver to Select Music/Chime.
Pressing and holding the ( ) on the receiver for 5s,the receiver will LED indicator on,which means receiver get into pairing mode.
Press push button, the receiver will the bell rings with LED indicator flashes,is pairing ok
Note: pair and set only one transmitter at a time to avoid interference and ensure successful operation.
It 10s without any operation, the doorbell will exit the pairing mode.
After selecting the Music/Chime, press the transmitter will automatically switch to the current ringtone. For the last paired transmitter.
For Pairing Additional Transmitters and receivers
Just repeat step 3 ,1-3, 2 -3, 3 for each additional transmitter or receiver.(Choose a different Music/ Chime for the 2nd transmitter to distinguish front and rear doors)
Note: This methad is suitable for multiple transmitters or multiple receiver pairing
Reset (Clearing out Settings)
Hold down volume button( ) and plug it into an outlet,After playing the beep twice and LED indicator on,all settings will return to factory defaults.

Installation

Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to see and hear.
1.For Receiver:
Plug-in receiver: Just plug receiver into standard outlet in room.
2.For Push button:
IMPORTANT:
Before installation, please test if the operating range you choose is working and set music if needed.
Before you drill any hole in the wall, please make sure there are not cables or pipes.
To install you will require a drill and cross-headed screwdriver.
1. Open the Transmitter with screw driver and separate the front cover from the back cover.
Penetrate the two standby holes at the back cover with two screws. Then fix the screws on the wall at suitable height.
2. Or you can stick the Transmitter with the double-sided adhesive tape.
If you are not mounting the push button to the wall, place it where you want it.

Battery Replacement of Push Button

Open the battery cover and install the CR2032 battery.
Note:When you replace the battery with a new one, be carefull to put the positive terminal of the battery facing upwards.

Specifications

| Doorbell| Push Button
---|---|---
Operating Temperature| -4°F to 140°F| -4°F to 140°F
Radio Frequency| 433 MHz| 433 MHz
Range (open field)| 1,000 ft| 1,000 ft
Sound Level (typical)| 0-110 dB|
Battery Type| Plug-in AC 110-250V| CR2032
Battery Life (5 activations/day)| Up to 5 years| Up to 3 years
Rain Proof| N/A| IP55
Internal Sounds| 60 Melody| N/A
Type of Bulb| LED/Blue| LED/Blue

Chimes List

1. Ding-dong, Ding-dong
2. Ding-dong, Ding-dong
3. Ding-dong, Ding-dong
4. Corsica Doorbell
5. Ding-dong
6. Ding-dong Chime
7. Hello Welcome (English)
8. Westminster Chimes1
9. Westminster Chimes2
10. Big ben electronic doorbell
11-40. NEWAGE-01~NEWAGE-030
41.Classical organ
42. Morning
43.Dingdong merrily on high
44. Waltz of the flowers
45.For Alice| 46. The William tell overture
47, The cuckoo waltzes
48. Minuet in G
49. Happy birthday
50. Fantaisie Impromptu
51. Yesterday Once More
52. Clarinet Polka
53. Russe Dance
54. Souvenirs Denfance
55. Jasmine Flower
56. Waltzes_Op. 34 No. 2
57. Hungarian Dance
58. Spring Song
59. Accordion Tango
60. Alarm Sound Effect
---|---

*Scrolling play function

Long press the next or previous button is automatically browses ringtones, saving you from having to operate buttons multiple times to select them.
After browsing to your favorite ringtone, short press the next or previous button to confirmed.

Commom Problems and Troubleshooting

Receiver suddenly can’t get signal from transmitter and doesn’t ring

Reason| Solution
Low-power battery
in transmitter.The less power in transmitter, the shorter range is.| Replace with a new battery.
Reset the receiver by accident so that transmitter is not paired with receiver any more.| Re-pair receiver with transmitter following the Operation Instructions.
There’s rust on the battery contacts or button area on PCB board of transmitter.| Remove the rust to see if it can re-work
Receiver keeps ringing continuously and LED indicator of transmitter stays on.
Raindrops have gone inside transmitter,which causes the short circuit and let transmitter keep transmitting signals.| Remove the battery and PCB board of transmitter and then dry them with a hair dryer. Change the install location of transmitter if necessary.