UNITY LASERBAR LL-Array 6RGB Laser Array Bar with Red Laser Beams and RGB LED Diodes User Manual

LL-Array 6RGB
USER MANUAL

Version 1.0

Unpacking Instructions

Read Manual before Operation
Dear user,
Thanks for choosing our device, believing this brand new product will bring you unlimited marvel and happiness. Before operating this device, please read this manual thoroughly, and retain it for future reference.

Warning Data
Please note the warnings in bold which will ensure the safe and smooth operation. These warnings are important to a certain extent.
Attention! Indicates a skill or other useful information for special situations.
Important! Indicates important information to protect personnel from incident or injury.
Caution! Prevent damage or injury from incorrect operation.
Laser! Laser safety warnning labels.

Warning!
If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a special cord or cord exclusively available from the manufacturer or his service agent.
Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches.
The lamps shall be changed if it has become damaged or thermally deformed.
The lamps shall be changed if it has become damaged or thermally deformed.

Unpacking Instructions
As receiving a fixture, carefully unpacking the carton, checking contents to ensure that all parts are in good condition. Informing the shipper immediately and retaining packing material for inspection if any parts damaged from shipping or device damaged. Keeping packing materials as evidence for shipper’s confirmation.

Attention!
This unit is in perfect condition before delivery, please check all accessories when unpacking the unit. User should follow this user manual to operate this unit, and make sure that you are clear on all laser safety information and unit operation before power it on. Any wrong operation will make this unit out of warranty.
Carefully moving after receiving it, checking whether there is any damage from shipping, and all the accessories in it.

Laser Safety Warnings
**** According to EN 60825-1:2014, this product belongs to class 3b.
Direct eye contact may cause injury.

This product is for laser show only. The class 3b laser light should be operated by professional operator only.

This is so-called show laser, emitting radiation with a wavelength spectrum between 400 and 700nm and producing lighting effects for shows.
International laser safety regulations require that lasers must be operated in the fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation between the floor and the lowest laser light vertically. Additionally, 2.5 meters of horizontal separation is required between laser light and audience or other public spaces.
Never direct the laser beam to people or animals and never leave this device running unattended.
The legal requirements for using laser entertainment products vary from country to country.
The user is responsible for the legal requirements at the location/country of use.
Warning! Avoid direct eye contact with laser beams during operation, especially when the laser beams stay still, or injury to eyes may occur.
Laser Safety Protection Feature
Caution! The laser security measures are designed according to the specific terms of the relevant international laser safety standards and has the following laser safety protection means.

Laser key switch: laser is available only when the key is turned on.
Laser Emergency switch: remote connecting switch, it will cut off the laser light path emergently once the device in potential hazard;
Laser indication : laser indication indicating the front panel of the laser light“ laser-ready ”
Laser safety labels: affixed line with European standards for multiple chassis laser safety stickers

Safety Instructions

To protect the environment, please try to recycle the packing material as much as possible.
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or metallic objects
**** Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regulation in your country.
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids.
The fixture must be fixed at least 20cm from surrounding walls
To avoid condensation to be formed inside, allow this unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages
Don’t cover any ventilation openings as this may result in overheating.
Don’t install it on flammable object.
Don not use it when maximum ambient temperature is higher than 40 degree,
Unplug the unit when it is not used for a longer time or before replacing the bulb.
Don’t open the top cover to avoid unit damage.
Please use the original packing when the device is to be transported.

**** Never expose the lens to direct sunlight, even for a short period, This may damage the light effect or even cause fire!

Safety Warnings
◆ Always connect the product to a grounded circuit to avoid the risk of electrocution.
◆ Always disconnect the product from the power source before cleaning or replacing the fuse.
◆ Avoid direct eye exposure to the light source while the product is on.
◆ Make sure the power cord is not crimped or damaged.
◆ Never disconnect the product from power by pulling or tugging on the cord.
◆ If mounting the product overhead, always secure to a fastening device using a safety cable.
◆ Make sure there are no flammable materials close to the product when operating.
◆ Do not touch the product’s housing when operating because it may be very hot.
Keep this User Manual for future use. If you sell the product to another user, be sure to give this document to the next owner.

Overhead Rigging

Attention! The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and /or damage to property. Overhead rigging required extensive experience! Working load limits should be respected, Certified installation materials should be used, the installed device should be inspected regularly for safety.
◆ Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
◆ Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The fixture must be fixed at least 20cm from surrounding walls
◆ The device should be installed out of reach of people and outside areas where persons may walk by or be seated.
◆ The device should be well fixed; a free swinging mounting is dangerous and may not be considered!
◆ Do not cover any ventilation opening as this may result in overheating
◆ Before the first time use, it must be inspected by professional staff to make sure safety, inspection regularly every year.

**** Before rigging make sure that installation area can hold the 10 times weight of device. Using the steel rope which can hold 12 times weight of device, through the eye-bolt for assisting hang installment.

AC Power
Please use the attached power, note that power voltage and frequency are the same as the marked voltage and frequency of device when connecting power. Every device’s power should be connected separately, so that device can be controlled individually.

Cable spec:

Product Installation

DMX-512 connection
◆ Connection between lights and DMX must use the shied cable of diameter more than 0.5mm. Please use the attached 5 pin XLR plug/socket to connect the DMX output/input interface. The connection between socket and cable as below( note the plug/socket’s 5 pin number and position).

◆ Note, XLR plug/socket’s 5pin can not be touched by inner hull, connection between pins is not allowed. Except above connection, XLR plug/socket can not be connected with XLR control line. Device receives international standard DMX512(1990) control signal.
◆ When using standard DMX512 control signal, the last device’s output interface must be connected to a DMX plug. This plug is putting a 120 ohm resistance between “canon” plug’s 2 pin and 3 pin. Showing as below pic. Sticking this plug into the last device’s signal output interface, it will avoid the interference during the process of signal transmission.

Operation instructions

fixtrue
6| DMX Output| 5PIN female XLR interface, for DMX communication
7| Cooling system| 6 sets of fan cooling in/out system
8| Safety eye| Attach the safety cable
9| LED Display| For setting model
10| Hanging bracket| For hang and angle adjustment
11| Key switch| Make sure the professional person use
12| Remote status LED| Remote controller connected ready
13| Laser status LED| Laser emission indicator
14| Remote control IN| Connect to the remote controller or previous laser projector
15| Remote control OUT| Connect to the remote control IN of next laser projector.

Menu operating instruction

Once after every power on the device, the VERSION and MANUFACTURE INFORMATION will be shown in LED monitor of rear panel. When the device is powered on, LED monitor on rear panel shows the current operating standalone mode or DMX address of DMX mode. With help of LED control panel, is very easy to set and change the operating mode of. After every resetting and saved, the new mode information will be shown on LED monitor at next power.
MODE Mode selection or back to the last function.
ENTER Confirm, enter into the deeper menu. Press it to save the chosen model or DMX initial add.
UP DOWN For changing DMX initial add or function value

| | LASER Auto shows(LA01-LA06)
| LED Auto shows(LE01-LE07)
| MIX Auto shows(LL01-LL06)
| Auto shows
****| Setting effect speed.01 is the slowest, 99 is the fast

| | LASER Sound shows(LA01-LA06)
| LED Sound shows(LE01-LE07)
| MIX Sound shows（LL01-LL06）
| Sound shows
| | Manual
| | Setting channel address
| Choosing DMX channel modes
| | Enter slave mode
| | Master enable
| Restore the factory default settings

Note: In sound mode, the fixture will turn off after 5 seconds automatically, if there isn’t any sound signal and will light on again once sound signal received.

Initial Setting

-LED
-MIX
-SOU
MAN| MANU| L.001-L.255 (LED brightness)| ENTER
S.000-S.100(LED strobe)
S. 000: off, S.099: on , S. 100: sound control strobe| ENTER
R.001-R.255 (Red laser brightness)
G.001-G.255 (Green laser brightness)
B.001-B.255 (Blue laser brightness)| ENTER
F. 000-F. 100(Laser strobe)
F. 000: off, F.099: on , F.100: sound control strobe| ENTER
DMX| 03CH( d001-d508)     08CH( d001-d504)
24CH( d001-d480)     28CH( d001-d476) 31CH( d001-d465)| choose channel mode Press ENTER to Save
dXXX| d001-dxxx| Set starting address Press ENTER to Save
SLA| SLAV| S. 001 to S. 255| Press ENTER to Save
SYS| M-EN| Enable/disable master| Press ENTER to Save
REST| Restore default settings| Press ENTER to Save

DMX operation instructions

This device adopts large storage and high speed chip, which has been written lots of effect based on DMX application. Before control other DMX channels, please be sure that the channel 1 was set in proper mode (value).

3CH

8CH

24CH

28CH

31CH

AVAILIABLE
070-099| Auto Led show
100-129| Auto mixed show
130-159| Auto Laser & Led show
160-189| Auto Laser show
190-219| Auto Led show
220-255| Auto mixed show
CH30| 000-255| Refer Ch2 of 3CH mode
CH31| 000-255| Playback Speed

Product parameter

Green(520nm/100mW, dimmable)
Blue(450nm/200mW, dimmable)
Beam diameter| 4mm
Beam divergence| <2mrad
Laser classification| Class IIIb (IEC60825-1)
Rate LED power| 3W warm wihte LED×6pcs
LED Beam angle| 7°
Connectors| 3 Pin XLR DMX in/out
Power consumption| 100-240V 50/60Hz 60W Max
Power linking| Neutrik PowerCon
Operation temperature| 10-40°C
Protection rating| IP44
Product Dimensions(WxDxH)| 1000×128×117mm (without handle)
Net Weight| 7.5Kg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>