decon wheel MED3311 Cleaner and Iron Remover Instruction Manual
- June 12, 2024
- decon wheel
Table of Contents
decon wheel MED3311 Cleaner and Iron Remover Instruction Manual
Assembly instructions for Guppy from 2018-01-01 – MED3311
- Check if it is the correct rear axle. See picture below.
If the rear axle does not look like this, you can order it from Anatomic Sitt.
-
Remove wheels and sleeves on both sides and anti-tip devices
-
Check the correct placement for the stop pin.
-
Assemble the plate (right side) according to picture.
Parts pair mounting set
| Item | No. | Part Number | Qty | Description |
|---|---|---|---|---|
| 1 | MED2000 | 1 | Bracket | |
| 2 | 405239 | 1 | Nordlock Washer M16 | |
| 3 | XSM16M | 1 | Nut M16 | |
| 4 | XSM8BR | 1 | Washer Plain M8 | |
| 5 | XSM8ML | 1 | Lock Nut M8 | |
| 6 | 100 400 017 | 1 | Spacer | |
| 7 | HW069 | 1 | Sleeve | |
| 8 | XSM8X35 | 1 | Screw Rounded M8 x 35 |
Assembly the back placed battery bag.
Alternative placement:
Order parts for battery placement under the seat. This is screwed on the
outside of the bracket for load anchoring. The chairs existing screws are
replaced, see yellow arrows in the picture below.
Note!
Remove the original anti tip device.
| Item | No. | Part Number | Qty | Description |
|---|---|---|---|---|
| 1 | MED1696 | 1 | Battery holder Guppy | |
| 2 | XSM8X20 | 4 | Screw Rounded M8 x 20 |
Installation of any parking brake.
The existing bracket for the parking brake is replaced and the parking brake
is transferred to the new bracket. Existing screws, washers and nuts are
reused.
| Item | No. | Part Number | Qty | Description |
|---|---|---|---|---|
| 1 | MED1695 | 1 | Bracket |
MED1389
Assemble of the joystick on the handle
Parts pair mountingset:
| Item | No. | Part Number | Qty | Description |
|---|---|---|---|---|
| 1 | X0C-48160-D0 | 1 | Swing Away Bracket | |
| 2 | MED1388 | 1 | Bracket | |
| 3 | XA2-2612E-00 | 2 | Clamp with hole | |
| 4 | XA2-2612K-00 | 2 | Clamp with tread | |
| 5 | XSM6BR | 2 | Washer Plain M6 | |
| 6 | XSM6X35 | 2 | Screw Socket M6 x 35 | |
| 7 | XSM6X16 | 2 | Screw Round M6 x 16 | |
| 8 | XSM6ML | 2 | Nut Self-Locking M6 | |
| 9 | NJF1021 | 1 | Pin | |
| 10 | NJF1020 | 1 | Pin Joint |
MED1252
| Item | No. | Part Number | Qty | Description |
|---|---|---|---|---|
| 1 | XSM6TG | 1 | Serrated Lock Washer M6 | |
| 2 | Xklamma2 | 1 | Clamp 22mm | |
| 3 | XSM6BR | 1 | Plain Washer M6 | |
| 4 | XSM6X20 | 1 | Screw Rounded M6 x 20 |
= MED1252 + MED1643
| Item | No. | Part Number | Qty | Description |
|---|---|---|---|---|
| 1 | XOC-48321-01 | 1 | Cable (Not included) |
Unless otherwise specified, use the following tightening torque.
Metric coarse threads, steel.
| Thread | Tightening torque |
|---|---|
| M3 | 1,2 Nm |
| M4 | 3 Nm |
| M5 | 6 Nm |
| M6 | 10 Nm |
| M8 | 25 Nm |
| M10 | 50 Nm |
| M12 | 85 Nm |
Sleeve
| Thread | Tightening torque |
|---|---|
| M16x1 | 30 Nm |
| M18x1 | 40 Nm |
2022-05-10
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>